This content now lives at makerforums and is continuing on there. Please go log in there with the same google account you used for Google+ and you will still own all the content you wrote.
This static site is out of date and not maintained now that the content is available at makerforums.
This site was an initial attempt to archive Google+ data about the HercuLien and Eustathios 3D Printers.
Posts
-
—
—
Hey everyone, first time poster here but Ive been reading most of the posts in the group for the last year or so
Hey everyone, first time poster here but I’ve been reading most of the posts in the group for the last year or so. I’ve designed a printer in Solidworks that is very much based on Eustathios V1 and Herculien, with a couple of twists.
-
—
—
I cannot express how happy I am
I cannot express how happy I am. +Michael K Johnson did me and this community a great favor. As we all know G+ is slowly approaching it’s “use by date”. And I don’t trust that google will gracefully sunset G+ with static content pages to retain the years of knowledge, sweat, community we have nurtured in our corner of the interwebs. So Michael who is …lets be frank… a computer ninja, helped make a backup of this community so it can be hosted out on Gitlabs. It started with a json and image export from https://gplus-exporter.friendsplus.me , then Michael worked his magic to convert it into usable data we could host remotely.
-
—
—
So my living situation, actually life situation in general has recently changed and I'm not sure if I'll have the time or space to run my Eustathios anymore
So my living situation, actually life situation in general has recently changed and I’m not sure if I’ll have the time or space to run my Eustathios anymore. If there’s anyone in the local area that would be interested, I’d be willing to let it go for cheap. Haven’t thought much on price yet. I’ll try to grab a picture of it soon but it does work quite well.
-
—
—
Hand tapping while watching football. After spending my recent hobby budget on trying to fix my existing printer, I'm back to working on the Herculien
Hand tapping while watching football. After spending my recent hobby budget on trying to fix my existing printer, I’m back to working on the Herculien.
-
—
—
Does anyone run dual extruders with single nozzle?
Does anyone run dual extruders with single nozzle? Care to share your thoughts? Can you share a pic of your setup?
-
—
—
If you are interested in a new hot-end or Bondtech SMG, Hobby-Fab is closing and they are selling off inventory
If you are interested in a new hot-end or Bondtech SMG, Hobby-Fab is closing and they are selling off inventory. Look at their inventory, add it to your cart, then use Coupon code CYAHF to get deep discounts of 30-50%. https://www.hobby-fab.com
-
—
—
This seller may be able to make custom beds for the Eustathios!
This seller may be able to make custom beds for the Eustathios! I have one for my prusa, it’s awesome no talc needed for petg
-
—
—
After i finished the Eustathios Spider V2 last year, i decided to build a smaller one from an old Cl260 (ultimaker clone) Frame: Eustathios Mini
After i finished the Eustathios Spider V2 last year, i decided to build a smaller one from an old Cl260 (ultimaker clone) Frame: Eustathios Mini.
-
—
—
Are any of you printing with PETG in your HercuLien?
Are any of you printing with PETG in your HercuLien? Are you doing anything special with it other than a higher temperature on the heater and bed. I read 240-265 for the extrusion and 80-100 for the bed. Any other special considerations?
-
—
—
Hey Guys, I got my Azteeg X3 setup and talking to my computer with Marlin, however, there is no motor movement
Hey Guys, I got my Azteeg X3 setup and talking to my computer with Marlin, however, there is no motor movement. I can see through the logs on Simplify 3D that the Board is receiving the command but still no movement. I have setup the boot pins for 16 steps. Is there anything I could be forgetting to do? Thanks.
-
—
—
Me again! Does anyone know how to get the bondtech STL's?
Me again! Does anyone know how to get the bondtech STL’s? They aren’t listed anymore.
-
—
—
Hey guys! Has anyone put a BL touch on their Eustathios warped plate and I really don't want to have to deal with leveling anymore
Hey guys! Has anyone put a BL touch on their Eustathios warped plate and I really don’t want to have to deal with leveling anymore.
-
—
—
Robots making robots... I decided to use Eric's models directly for the CAM
Robots making robots… I decided to use Eric’s models directly for the CAM. Figured, might as well, right? Feels almost like cheating…
-
—
—
Misumi order is finally in and a big step closer to starting my Herculean build
Misumi order is finally in and a big step closer to starting my Herculean build. Exciting times ahead!
-
—
—
NSFW Just wanted to show some printing action cookie cutter that I designed based on a Etsy one I found a few months ago
NSFW Just wanted to show some printing action cookie cutter that I designed based on a Etsy one I found a few months ago. Printed this as 160 mm/s and it turned out really well; unfortunately I ruined it by trying to anneal in my oven. So I printed a second one that I will not anneal.
-
—
—
Hello Eric Lien and all :) For a better alignment, a single bronze bushing is not better than two Press-Fit bronze ?
Hello +Eric Lien and all :)
-
—
—
My Eustathios Spider V2 is stopping mid print
My Eustathios Spider V2 is stopping mid print. It gets so far and just stops printing. As of right now it will not complete a full print. I’m using the X5 Mini Wi-Fi and today I swapped out the SD card for a newer one. I’m using the ESP3D web GUI for the X5 Mini Wi-Fi, where I upload the sliced Simplify3D files and then start the print.
-
—
—
Top panel finally done! Ran this guy 22 hours a day for a month no breakdowns!
Top panel finally done! Ran this guy 22 hours a day for a month no breakdowns!
-
—
—
Hey guys, as college is approaching, I am looking to build my self a small 3D printer that can hide under a bedside table or something
Hey guys, as college is approaching, I am looking to build my self a small 3D printer that can hide under a bedside table or something. My Eustathios and CR-10S are way too big.
-
—
—
Well, my pile is starting to grow!
Well, my pile is starting to grow! I’ll be putting my order in to misumi in a couple weeks. Trying to scratch all the big ticket items off the list right now.
-
—
—
My BMG's should be arriving in a couple days
My BMG’s should be arriving in a couple days. What size stepper have people been driving them with? I don’t know that they need as much torque as the cartesian axes steppers, but then again, it shouldn’t hurt anything Opinions?
-
—
—
Hey everyone, Im looking at building the Eustathios Spider V2 and looking at doing walters bed however I cant figure it out, I'm a very visual and cant picture it
Hey everyone, Im looking at building the Eustathios Spider V2 and looking at doing walters bed however I cant figure it out, I’m a very visual and cant picture it. can someone please share some photos of it?
-
—
—
Does anyone use a Z probe with their printer?
Does anyone use a Z probe with their printer? Would you care to share your leveling results?
-
—
—
Are they getting rid of Google+? Any ideas where we would have this community?
Are they getting rid of Google+? Any ideas where we would have this community? +Eric Lien
-
—
—
Its been kind of quiet in here lately...figured I would throw this out there as show and tell before I installed it
Its been kind of quiet in here lately…figured I would throw this out there as show and tell before I installed it. Its a lot easier to see uninstalled.
-
—
—
For those who use the Spyraflo self aligning bushings, did you press them into the receiving bore or just to the knurl> Do the faces sit flush to the surface or stick out?
For those who use the Spyraflo self aligning bushings, did you press them into the receiving bore or just to the knurl>
-
—
—
It has been awhile, my Herculien still going strong but I am only using it to print large items with a 1.2mm Volcano nozzle
It has been awhile, my Herculien still going strong but I am only using it to print large items with a 1.2mm Volcano nozzle. Needed a smaller printer and this printer started as a Cetus printer. It is a great little printer for what it is, but I needed much more customized settings, heatbed control, the electronic endstop was unreliable. Gutted the electronics, installed a Aero Extruder at first and that was a disaster for me anyways (inserting a new filament was a nightmare) , replaced with a Bondtech BMG extruder (I should have started with it in the first place) added on a E3D-V6 hot end. Gonna try .25mm nozzle, been playing with .4mm for now. I used my spare Azteeg X3 controller with TMC2208 drivers (super quite, fan noise only during printes). Changed out the hot end fan with a 40mm fan. Attached an Octoprint/Raspberry Pi with a cam mounted to the Z axis. If anyone is interested in doing the same thing, I can post the printed files for conversion.
-
—
—
Eustathios folks- what kinds of speeds and feeds are you using ?
Eustathios folks- what kinds of speeds and feeds are you using ? These are my KISS settings for PETG and I feel while i get GREAT prints with them, I want to try speeding things up a bit.
-
—
—
My Eustathios Spider V2 only likes to print Hatchbox PLA
My Eustathios Spider V2 only likes to print Hatchbox PLA.
-
—
—
My current bed setup is pei on a sheet of glass, over a very bent aluminum plate
My current bed setup is pei on a sheet of glass, over a very bent aluminum plate.
-
—
—
Hello I am cleaning out my work corner and would like to sell off my parts ( screws and bearings etc) for a ridiculous discounted price
Hello
-
—
—
Hey guys! I do not know why is my printer stoping while it is printing circles
Hey guys! I do not know why is my printer stoping while it is printing circles. My controller is smoothieboard.
-
—
—
Just saw these. I have heard they dont do anything on nice drivers
Just saw these. I have heard they don’t do anything on nice drivers.
-
—
—
What would cause thermal runaway errors? This is Marlin on Ramps and its been working like a champ
What would cause thermal runaway errors? This is Marlin on Ramps and its been working like a champ. Then today all the sudden, wham! There are little blips like this asking the temp track. the timelapse shows nothing. printer is in the basement in a draft free area (home brew kegs and carboys right next to this. I am a little mature as to where to start diagnosing.
-
—
—
Time to order ballscrews for my Herculien build and recently saw a question related to one I had: Are the ballscrews linked in the BOM already machined correctly or should I have them machined to the same spec as the
Time to order ballscrews for my Herculien build and recently saw a question related to one I had:
-
—
—
PETG? I cant get it to print well, what are your tips?
PETG? I cant get it to print well, what are your tips?
-
—
—
Trying something new this week. Ninjatek Cheetah filament
Trying something new this week. Ninjatek Cheetah filament.
-
—
—
So Im about ready to use my Panucatt X5 GT as a damn frisbee
So I’m about ready to use my Panucatt X5 GT as a damn frisbee. Thing has cost me more in wasted plastic due to freezing and other crap. Haven’t looked at what’s new for boards these days. What’s everyone using these days?
-
—
—
A few photos of my build. I'm calling it finished but I already have a few mods in mind
A few photos of my build. I’m calling it finished but I already have a few mods in mind. Since my last post i have got the bed working - 10mm cast aluminium with 3 point levelling and it is working really well. It’s bulletproof flat although it takes quite a while to cool down after a print so might look for a removable build surface. Initially the bed moved a bit. The cause was play in the LM10LUU linear bearings which I got from Robotdigg. I got the rods from Misumi so I ordered new bearings from them and they are perfect - just tolerance differences.
-
—
—
I'm trying to figure out how to specify to the vendor what to machine off the ballscrew shafts before ordering them for the Eustathios
I’m trying to figure out how to specify to the vendor what to machine off the ballscrew shafts before ordering them for the Eustathios. This is but one of dozens of questions I have but I don’t want to clog up the forum because the questions will come one at a time.
-
—
—
I read something awhile back about Eric suggesting ordering the silicone heater with a hole in it so the thermistor can be replaced
I read something awhile back about Eric suggesting ordering the silicone heater with a hole in it so the thermistor can be replaced. Any ideas how big the hole should be? My idea was 15-20mm, but I’m not sure if that’ll leave enough surface area for the thermistor to stay adhered to the heat spreader
-
—
—
Tramming & Bed Leveling- I am pretty sure my bed is level but it does not trammed to the axis of the hot end
Tramming & Bed Leveling- I am pretty sure my bed is level but it does not trammed to the axis of the hot end.
-
—
—
Tariffs- anyone know if the tariff wars that are going to be surcharged onto robotics are going to affect 3D printers?
Tariffs- anyone know if the tariff wars that are going to be surcharged onto robotics are going to affect 3D printers?
-
—
—
First print from my Eustathios V2! Well, I actually I printed 2 x 20mm calibration cubes to check e steps then this
First print from my Eustathios V2! Well, I actually I printed 2 x 20mm calibration cubes to check e steps then this. Printed with 18 month old PLA on the spare “build tak” that came with my Wanhao taped to the bed with no bed heating and no optimisation of settings at all. I couldn’t be happier! I’ve still got a number of things to finish and I’ll post some pics and thoughts once I get everything done.
-
—
—
Hello! I have a source for custom spring steel magnetic PEI coated beds, laser engraved and cut to size
Hello! I have a source for custom spring steel magnetic PEI coated beds, laser engraved and cut to size. Also magnetic.
-
—
—
Hello. Now that my eustathios is my main printer for my 3D Hub, I want to go much faster than 60mm/s
Hello. Now that my eustathios is my main printer for my 3D Hub, I want to go much faster than 60mm/s.
-
—
—
I wanted to put this out there for folks- I FINALLY finished remixing Walter Hsiao 's miniblock carriage- I added a shelf to locate the E3D V6 hotend, a top cap and fan duct that accepts David Crocker's IR sensor board, I am
I wanted to put this out there for folks- I FINALLY finished remixing +Walter Hsiao ‘s miniblock carriage- I added a shelf to locate the E3D V6 hotend, a top cap and fan duct that accepts David Crocker’s IR sensor board, I am cleaning up the files and stl’s and will put on github in the next few days.
-
—
—
Extruders- I was watching this video, this Ultimaker has some sort of boom arm with the extruder on it
Extruders- I was watching this video, this Ultimaker has some sort of boom arm with the extruder on it. Has anyone seen something like this? I have extra rods from mis-measuring my frame and some extra bushings. I know Walter did an articulating arm with bearings but this seems a little bit simpler. The notes say Bondtech, but I don’t recognize it as such.
-
—
—
Heatbed - Heatspreader plate issues- I have been chasing bed leveling issues for a while, it was like trying to corral jello constantly...
Heatbed - Heatspreader plate issues-
-
—
—
Hello, anybody use a volcano nozzle on the 3d printer
Hello, anybody use a volcano nozzle on the 3d printer.
-
—
—
Questions, I'm looking at the bill of materials: 1
Questions, I’m looking at the bill of materials:
-
—
—
Carriage wiring I've added an IR probe recently and now have 15 spearate (single) wires going to the cartridge (2 hotends, 2 fans, probe) - which seems a lot
Carriage wiring
-
—
—
I think I have goofed on configuring Marlin and my coordinate system
I think I have goofed on configuring Marlin and my coordinate system. This is the first time I printed text upside down and it came out backwards and upside down. The line of text and symbol are flip-flopped top/bottom and they read backwards.
-
—
—
Update on my build. Slowly working out where everything goes and hopefully hard wiring everything shortly
Update on my build. Slowly working out where everything goes and hopefully hard wiring everything shortly. End stops in and working. Have had the z axis moving. Got a replacement screw from Golmart - straight as an arrow but it has a little rough spot which is a bit disappointing. Am going to have mains heated bed - got a keenovo heater for that. 10mm cast Ali plate (worried about the weight) - going to try 3 point levelling. Also got a panel due. A few more mounting parts to finish designing/ print and I’ll take the bond tech off my wanhao and put it on this one. Hopefully post a break in vid in a week or so!
-
—
—
Thanks to the generosity of Eric Lien at the 2018 MRRF I was recently able to change out the Smoothieboard V1.0b I'd been running on my Herculien to an Azteeg X5 GT with Bigfoot BSD2660 drivers
Thanks to the generosity of +Eric Lien at the 2018 MRRF I was recently able to change out the Smoothieboard V1.0b I’d been running on my Herculien to an Azteeg X5 GT with Bigfoot BSD2660 drivers.
-
—
—
Hey all just an FYI that I adapted Eric Lien's original Eusththios Spider 2 carriage for 2 M8 linear bearings: This is an alternative carriage for a Eustathios Spider 2 3D printer that uses m8 linear bearings instead of
Hey all just an FYI that I adapted Eric Lien’s original Eusththios Spider 2 carriage for 2 M8 linear bearings: https://www.youmagine.com/designs/alternative-eustathios-3d-printer-carriage-uses-m8-linear-bearings
-
—
—
Anyone need a heater/spare? Anyone want to do a group buy?
Anyone need a heater/spare? Anyone want to do a group buy?
-
—
—
Rod Wear? How do your rods appear to be wearing in?
Rod Wear?
-
—
—
Great interview of Walter Hsiao out on Thingiverse
Great interview of +Walter Hsiao out on Thingiverse. It is worth a read about a great designer, community member, and fellow builder of the Eustathios printer.
-
—
—
Needed something to print, just to make sure the printers don't collect too much dust
Needed something to print, just to make sure the printers don’t collect too much dust. Trying the Makers Muse torture egg. I like printing perimeters outside in for better surface finish and tolerance (inside out can push last outside perimeters out if the inside perimeters are at all overstuffed). Looks like i need to dial in a hait more. The knife edge created by the window cut-outs in the egg leaves no room for error if the start of extrude begins on the edge. I wish you could tell simplify3d not to start at an edge. If it is a simple geometry I can define a seam start location. But for something with radial symmetry there is no good solution. That being said, not bad for a printer with a 850mm Bowden Tube ;) (but there is always room for improvement).
-
—
—
Any tips to bed leveling with the 4 adjusters?
Any tips to bed leveling with the 4 adjusters? I feel like I am trying to negotiate with Jello.
-
—
—
Enclosure Three years after I started the build, I finally managed to finish the printer and install the enclosure
Enclosure
-
—
—
If any of you are looking for a Bondtech on a discount hit up Brandon at SMW3D
If any of you are looking for a Bondtech on a discount hit up Brandon at SMW3D. He and I worked on a printer a while back. Looks like he is going a different direction on the extruders (Bondtech BMG versus the big dog QR’s). If you are using a bowden setup on HercuLien or Eustatios, and looking to save a few sheckles on a Bondtech QR, I think these would serve you well.
-
—
—
Bed weight & thickness. Wondering if I need to be concerned about weight and if that has an impact on z-hops etc?
Bed weight & thickness. Wondering if I need to be concerned about weight and if that has an impact on z-hops etc?
-
—
—
Can anyone help debug/diagnose this? These are 25x25x2mm flats that I tried printing to calibrate Extrusion constant....
Can anyone help debug/diagnose this? These are 25x25x2mm flats that I tried printing to calibrate Extrusion constant…. the right side of the print is missing completely on the top layer. The print direction from the gcode is top left to bottom right of the flat.
-
—
—
Motor Flex- Do the motors flex on your printer when under load?
Motor Flex-
-
—
—
MRRF is a blast!
MRRF is a blast!
-
—
—
Arrived in Goshen, IN with my HercuLien, Ready for MRRF!!!
Arrived in Goshen, IN with my HercuLien, Ready for MRRF!!!
-
—
—
What do people think about this? It'd be nice to have multi material prints sorted reliably
What do people think about this?
-
—
—
Last night during a print the heater cartridge on my hotend must have caused some sort of burn
Last night during a print the heater cartridge on my hotend must have caused some sort of burn. Interestingly it kept working and even finished the print.
-
—
—
Ballscrew straightness. When I have my bed down at the bottom and raise it or lower it by pulling the belt the ballscrews wobble at the top
Ballscrew straightness. When I have my bed down at the bottom and raise it or lower it by pulling the belt the ballscrews wobble at the top. On one side 0.2mm and on the other 1.5mm. I don’t have huge expectations from a $20 chinese ballscrew (Golmart) and freight is more than the cost of the item so hardly going to send them back, but I presume this will cause artifacts in my prints?
-
—
—
Alright guys and gals. Anyone heading to MRRF 2018
Alright guys and gals. Anyone heading to MRRF 2018. I am going out. Just want to know who to be on the lookout for.
-
—
—
Anyone here have experience with Printbite? Any better than PEI sheet?
Anyone here have experience with Printbite? Any better than PEI sheet?
-
—
—
Alright ladies and gents, I'm about to install my silicone heater to my aluminum plate
Alright ladies and gents, I’m about to install my silicone heater to my aluminum plate. Been hesitant to do it as the install is likely pretty permanent and I’m worried I’ll make a mistake on the cable routing. Where did you guys put your cable exiting? How did you handle the cabling? Cable chain? For there record, I think I have the square one with the centered wire that is called out in the BOM.
-
—
—
Making progress (this is just a test assembly to check things fit etc not the final build)
Making progress (this is just a test assembly to check things fit etc not the final build). Heated bed and bed plate the last big items to sort out. I got a mains silicon heater but have since started having second thoughts - 220V here, kids etc. So thinking I might revert to a 24 volt heater for the time being. How long is it likely to take to heat the bed to 60 Deg C? (PLA/PETG). I have a duet. Power supply is 24v, 10A. SSR still? Second power supply? etc. Recommended 24V silicon heater? Any advice much appreciated.
-
—
—
My optimal layers heights are funky- using the TR8x8 lead screws, with 20T on the motor and 32T on the leadscrews, with 1/32 stepping, i get 1280 steps/mm
My optimal layers heights are funky- using the TR8x8 lead screws, with 20T on the motor and 32T on the leadscrews, with 1/32 stepping, i get 1280 steps/mm.
-
—
—
I have inconsistent layer registration. Is this likely caused by belts?
I have inconsistent layer registration. Is this likely caused by belts? Too tight? Too loose? Something else?
-
—
—
FOR SALE: I was going to build a Eustathios Spider V2 but illness got in the way so parts are now for sale
FOR SALE: I was going to build a Eustathios Spider V2 but illness got in the way so parts are now for sale. No description (sorry no time), check the pics. NO MINIMUM PRICE (but it has to be worth my while). I’m not selling bits n pieces individually, preferably the whole thing as a lot. Moving house soon so if it doesn’t go it’s going to charity shop. Location Australia so buyer pays postage. $15USD registered. PayPal only. For sale until paid through PayPal . Thanks!
-
—
—
Its not pretty, but its a print
Its not pretty, but its a print. A trainwreck it might be, but its a print.
-
—
—
First print in the books. Everything was going so well until the end there...
First print in the books. Everything was going so well until the end there… not exactly sure what caused the shift as I was not immediately in the area at the time. Will have to check out why. Other than that, I’m really impressed with how nice of a print I’m getting on my first attempt!
-
—
—
Got a problem that hopefully you guys have encountered and can help me with
Got a problem that hopefully you guys have encountered and can help me with. For reference I’m using Slic3r.
-
—
—
My Eustathios Spider V2 keeps pausing multiple times mid print
My Eustathios Spider V2 keeps pausing multiple times mid print. I swapped the USB cable. My laptop is a Core i7 running Windows 10. I’m using the Azteeg X5 Mini WIFI.
-
—
—
Components arriving in the post and parts starting to roll off the production line...
Components arriving in the post and parts starting to roll off the production line…
-
—
—
Any tips for overall alignment? One of the bars was bent
Any tips for overall alignment? One of the bars was bent. I am not sure how I missed it, but Jared at PD-Tech replaced them and took care of me and sent replacements free of charge. . .
-
—
—
Does a parts cooling fan make a difference;
Does a parts cooling fan make a difference; YES!
-
—
—
I've just finished my biggest print ever, a 1.3kg CF reinforced PETG model, for a client
I’ve just finished my biggest print ever, a 1.3kg CF reinforced PETG model, for a client. I had to use the whole 300x300mm of the build plate and used a Volcano with a 1mm nozzle, 0.4mm layers and 50% infill, and took 2 full days to finish. I was shit scared to be honest, especially when I realised towards the end that I had forgotten some additional supports (and quickly squeezed some EPP foam into the nut holes, which worked a treat to support the layers above!).
-
—
—
Anyone have crazy thermistor readings? I am trying to figure this out and my electronics knowledge is hampering my efforts
Anyone have crazy thermistor readings? I am trying to figure this out and my electronics knowledge is hampering my efforts.
-
—
—
DO you ever just scare yourself with your printer, and after thinking about it, laugh about it?
DO you ever just scare yourself with your printer, and after thinking about it, laugh about it?
-
—
—
PID Tuning? I'm having some trouble with printing PETG
PID Tuning?
-
—
—
Is anyone using stall detection on the DuetWifi?
Is anyone using stall detection on the DuetWifi?
-
—
—
A few questions about stepper motors: (1) 0.9 or 1.8 deg?
A few questions about stepper motors:
-
—
—
Need to start thinking about controllers. I've budgeted for a good quality one, and am thinking maybe a duet with no screen but am interested to hear what people are using and/or recommend?
Need to start thinking about controllers. I’ve budgeted for a good quality one, and am thinking maybe a duet with no screen but am interested to hear what people are using and/or recommend?
-
—
—
I have broken it breaking it in :( What seemed to start so well ended rather embarrassingly disastrous
I have broken it breaking it in :( What seemed to start so well ended rather embarrassingly disastrous.
-
—
—
It Lives! After wrestling with configuring Marlin and cleaning up some wiring, I have successful motion
It Lives!
-
—
—
Enclosure for the Smoothieboard. Found this on Thingiverse by cope413, and it came out pretty well
Enclosure for the Smoothieboard. Found this on Thingiverse by cope413, and it came out pretty well. Still learning, still tuning, but this felt good. Cura 3.2.1, 200 C, 60 on bed, PLA. Octoprint/OctoPi. Needs a touch of clean-up, still learning on printing support.
-
—
—
How did you all manage the cable routing on your frame?
How did you all manage the cable routing on your frame? The ones I am trying to work out are the endstop cables that have to run horizontal then vertical to the bottom.
-
—
—
The obligatory first buildlog post. For anyone in NZ looking for a frame I got this from "Mecha4makers" in Wellington
The obligatory first buildlog post. For anyone in NZ looking for a frame I got this from “Mecha4makers” in Wellington. Nice to deal with, good price and very nicely machined. I roughly put the frame together with no corner brackets or tweaking and the top was perfectly square and the bottom was out by 0.5mm so very happy.
-
—
—
Just wanted to some honey comb fun for a part I am designing for heavy industrial use
Just wanted to some honey comb fun for a part I am designing for heavy industrial use. First in PLA, and a final version in taulman 910. Any advice on printing nylon? All I know is that it needs to be dry and about 260c.
-
—
—
I am trying to design a graduated thumbwheel for the bed leveling bolts
I am trying to design a graduated thumbwheel for the bed leveling bolts. I find it most convenient on my Di3 to have the calibrated nuts to adjust the bed.
-
—
—
Here are some photos of the cracking
Here are some photos of the cracking. +Dennis P was asking me for some pictures and thought the rest of you might be interested too.
-
—
—
Hey all, As I'm pulling my hair out with alignment issues, I noticed that several of the parts I printed are fracturing, mostly around where the bushings are inserted
Hey all,
-
—
—
So enjoying learning all about printing, infill, etc
So enjoying learning all about printing, infill, etc. Loaded up a raspberry pi image OctoPi with OctoPrint, and refining settings. Here is a rPi enclosure from Thingiverse that had 8020 in mind. Getting better quality with each tweak.
-
—
—
Alternate Z bracket- I goofed when I ordered belts
Alternate Z bracket- I goofed when I ordered belts. My frame is stretched 30mm, and I really need a belt ~1060mm in length. I ordered and got 976mm. TOO SHORT! Not many options… Its not long enough to even get around the motor or pulley.
-
—
—
Real Estate! I am at the point that I need to decide the fate of my Eustahios bed....
Real Estate! I am at the point that I need to decide the fate of my Eustahios bed…. The heat spreader is oversize in the L-R direction of the photo.
-
—
—
Linear shaft. I'm going to get misumi to avoid any hassles form cheaper options
Linear shaft. I’m going to get misumi to avoid any hassles form cheaper options. Should I be getting chromed rods? The code in the BOM (eg SFJ10) appears to be un-chromed? Which is the correct code for the chromed ones?
-
—
—
Hi from New Zealand. I'm new here and am about to start building a Eustathios V2
Hi from New Zealand. I’m new here and am about to start building a Eustathios V2. Have had a Wanhao I3 (plus mods) for a year or so loving that and decided to build one myself for the fun/experience but also to hopefully end up with a better printer. Have agonised over what to build…corexy hype etc etc but it was the quality of support in this group the clinched it for me.
-
—
—
Hello all. Together with my students, We are building the Eusthatios
Hello all.
-
—
—
Well, after quite a few attempts, and lots of questions, I am printing pretty decent parts
Well, after quite a few attempts, and lots of questions, I am printing pretty decent parts. Thanks to all the responses to my questions, I have had 20 hours of good printing. I know they are not perfect, and I need to make some more adjustments but happy to say I am on the printing road now!
-
—
—
So I couldn't help myself and I tore apart a perfectly working Eustathios to install a modified carriage that has mounts for a 40mm fan to quiet it down a bit
So I couldn’t help myself and I tore apart a perfectly working Eustathios to install a modified carriage that has mounts for a 40mm fan to quiet it down a bit. Of course, now I’m struggling to get it back to its former glory. The carriage movement isn’t quite as smooth, but not binding terribly.
-
—
—
Alrighty, I've made some good progress this weekend finally, had the gantry moving pretty nicely, not quite one finger smooth but close
Alrighty, I’ve made some good progress this weekend finally, had the gantry moving pretty nicely, not quite one finger smooth but close. Put the motors on and did some movements and got lots of friction in all directions. Loosened up some of the bearing holders and moved them around and got even closer! However, I am still getting friction in the X axis, but only one direction, the other direction is smooth. Any idea what causes this particular issue?
-
—
—
Can you all talk to the fans and fan positions/ adapters you have on your Herculien around the extruder?
Can you all talk to the fans and fan positions/ adapters you have on your Herculien around the extruder? I currently have the fan that came with the E3D Volcano, and it runs constantly. I have a second fan that is on the carriage, but I have it disabled because it seemed to be messing up my extruder. Any relevant pictures would be appreciated.
-
—
—
More advice needed! I am checking on the Z for the banding Eric Lien mentioned
More advice needed! I am checking on the Z for the banding +Eric Lien mentioned. I think my belts are tight, but this print is terrible. Also reviewing a common printing problem page that +Dennis P sent me. I think I also should have printed this on its side, but it printed from the back bottom up into the air. Lots to learn about the slicing.
-
—
—
Hi, I've got unfinished printer project parts to sell
Hi, I’ve got unfinished printer project parts to sell. Wanted to check first is it okay to post it here +Eric Lien?
-
—
—
Belts! Anyone need belts? After waiting for 5 weeks, Robot Digg figured out that my order was 'lost'...
Belts! Anyone need belts?
-
—
—
Who out there is using the smoothieboard on the HercuLien?
Who out there is using the smoothieboard on the HercuLien? I worked with +Dennis P and have made several solid steps forward, but somewhere I am still missing something with the Z height. I looked back in the discussion history for the proper calculations, and tried twice with the Triffid Hunter Calibration Guide, and tried the setting for gamma with the results, but I still cannot get it right, so I am asking what your setting is for gamma:
-
—
—
New member here. I am collecting parts for a Eustathios build
New member here.
-
—
—
Progress Report #2, Thanks for all the feedback
Progress Report #2, Thanks for all the feedback. I am getting much closer to where I want to get to this weekend! Thanks for all the responses. I think X and Y are on the money. Tightened belts, check settings, and got the latest version of Cura. Now I just have to figure out the Z. This test cube ( +Dennis P ) told me to try really helped. Tweaked, tried to print, tweaked again. Z is off by a bit. But much better than yesterday.
-
—
—
Hi all, Progress report. New BMG is on and delivering solid runs of material, so happy with that
Hi all, Progress report. New BMG is on and delivering solid runs of material, so happy with that. I think I need some input on what I am looking at on these prints, for feedback on what I may need to adjust to get better quality now that the flow is good. I do have a larger nozzle on this as part of the E3D Volcano setup. My goal is print parts for a inMoov robotics project, but I know I need to clean these things up before I attempt to do larger parts. I ran the extruder at 230 C, and the heated bed at 110 C. Movement looks good to me, but put a link to a video in as well, so that I can get feedback there as well. Any and all input is welcome.
-
—
—
Question about axis rod layering and Z bed height- I am in the middle of putting stuff together and I keep looking at the printer and the model and I can not shake the feeling am assembling something in the wrong position
Question about axis rod layering and Z bed height- I am in the middle of putting stuff together and I keep looking at the printer and the model and I can not shake the feeling am assembling something in the wrong position.
-
—
—
This is the best I am getting it
This is the best I am getting it.
-
—
—
ordering glass beds from the place in the BOM
ordering glass beds from the place in the BOM. anyone want to do a groupbuy? i’ll be getting the quotes later today and will post them.
-
—
—
It does not look pretty, but I have the new Bondtech BMG mounted and stepper motor wired in
It does not look pretty, but I have the new Bondtech BMG mounted and stepper motor wired in. I Think this is the smoothest unit I have experienced to date. I need to figure out the steps to put into the Smoothieboard configuration, but the second picture shows a nice long run of melted plastic, so I am excited.
-
—
—
This keeps happening after rebuilding my Eustathios Spider V2 and installing a new Azteeg X5 Mini WIFI with SD2224 drivers
This keeps happening after rebuilding my Eustathios Spider V2 and installing a new Azteeg X5 Mini WIFI with SD2224 drivers. It shifts on every print job.
-
—
—
Build plate heaters- Has anyone tried using 4 ~160mm x 160mm 12V square heaters instead of the one large one under the build plate
Build plate heaters- Has anyone tried using 4 ~160mm x 160mm 12V square heaters instead of the one large one under the build plate. 4*$6 instead of large 320mmx320mm one for $120?
-
—
—
Two years ago almost to the day I posted some questions and got a lot of great responses
Two years ago almost to the day I posted some questions and got a lot of great responses. I now realize I wasn’t ready to jump in to building my own printer though. I got way too frustrated with my Wanhao i3 and it say collecting dust for awhile.
-
—
—
Turns out it was the drivers overheating
Turns out it was the drivers overheating.
-
—
—
Eric and all, I definitely have had problems lining out my HercuLien
Eric and all, I definitely have had problems lining out my HercuLien. I have had it built for quite a while, and I have had some luck getting small prints to be successful but they are far from perfect. I have asked a few questions now and again trying to get it better, but I still am not where I can get a print without a lot of attempts.
-
—
—
Anyone have an opinion on what is the best Bin file to be updating to for my Azteeg X5 GT ?
Anyone have an opinion on what is the best Bin file to be updating to for my Azteeg X5 GT ?
-
—
—
Completed my frame a couple weeks ago and am really struggling with getting the carriage to move freely
Completed my frame a couple weeks ago and am really struggling with getting the carriage to move freely. As in it takes a whole hand to push it around and often with another hand on the frame. Very stiff! I went through the great gantry alignment video and still things are quite tight. I understand that this might just mean I need to take things apart and perhaps try again, but I was curious if anyone here could offer some tips or tricks that I could try prior to doing so.
-
—
—
Finally added part cooling fans I didn't want to glue the fans to carriage so I designed a little fixing clip that holds the fans
Finally added part cooling fans
-
—
—
Would people be interested in doing a community swap /group buy for some of the hardware?
Would people be interested in doing a community swap /group buy for some of the hardware? Kind of like friends of Carl for sourdough or PFranc for Garmin connectors where we share. Does something like this already exist?
-
—
—
Anyone have a partially completed Eustathios or Herculien printer (or parts kit) they are looking to sell?
Anyone have a partially completed Eustathios or Herculien printer (or parts kit) they are looking to sell? I’m thinking about building a second printer.. figured I’d ask here first before going out to buy components.
-
—
—
Ok silly question for those using Walter's print bed leveling blocks
Ok silly question for those using Walter’s print bed leveling blocks. How exactly do I attach my bed using those spring spacers? There’s no hex indent for a captive nut on the bottom so I’m a little bit lost how to build up that stack. I get how to attach it to the extrusions, just lost on mounting the bed plate. Thanks in advance!
-
—
—
I would like to ask about earthing
I would like to ask about earthing. How to wiring it?
-
—
—
I could use some pointers on making some of the printed parts- i am not liking the slicing and support results I am getting
I could use some pointers on making some of the printed parts- i am not liking the slicing and support results I am getting.
-
—
—
working on getting all the parts collected to make the eustathios v2, and there is one part i just cant seem to find
working on getting all the parts collected to make the eustathios v2, and there is one part i just cant seem to find. 7Z41MPSB08M 8mm self-lubricated bearing. ultibots is sold out for a while, sdp-si is sold out, QBC is also sold out. can any pressfit self-lube 8mm bearing work? or do you guys recommend a different one altogether.
-
—
—
Hmm. I wonder if this would make a great difference Mic6 Alum upgraded z motor
Hmm. I wonder if this would make a great difference
-
—
—
Anyone know the connectors on this little board?
Anyone know the connectors on this little board? I beleive that’s a 3 pin JST XH connector but what about the black ones? The 10 pin male and female?
-
—
—
Question- I am going to ask this here because y'all seem like a pretty sharp bunch...
Question- I am going to ask this here because y’all seem like a pretty sharp bunch… is there a more direct way to generate GCode to print instead of taking a solid model, processing it and exporting to a mesh of triangles only to interpret and then reconstruct it back into a solid model through via a slicer? Every step additional step introduces errors. STL destroys the curves. If it took a NURBS, STEP or similar file and kept the geometry intact, that would be different.
-
—
—
And so it begins.... extrusions to process and parts to print!
And so it begins…. extrusions to process and parts to print!
-
—
—
Quick question for those that have experimented
Quick question for those that have experimented. How fast have your printer run reliably? I kinda recall that some have run 300mm/s just fine without any alterations to their prints. Can anyone confirm what “normal” printing speeds I’m looking at getting out of my printer? Also any suggestions for looking into changes to the design to improve? Aside from going the linear guide rail route?
-
—
—
UPDATE: Roy has sent me a replacement board for free :) I really don't know whats so great about these Azteeg boards anymore
UPDATE: Roy has sent me a replacement board for free :)
-
—
—
last question for tonight...how many links in the cable chain does it take to link up the Herculien?
last question for tonight…how many links in the cable chain does it take to link up the Herculien? +Eric Lien Can you or anyone else advice?
-
—
—
And we are cooking, first print for the Herculien in it's classic red color
And we are cooking, first print for the Herculien in it’s classic red color. I decided to go PETG. I am not setup for fumes from ABS. Printing one of the 3 extrusion drill guides.
-
—
—
I have a a few questions (OK, 6) about the BOM, ballscrews and Linear shafting
I have a a few questions (OK, 6) about the BOM, ballscrews and Linear shafting. Thanks for making the model available, it really helps to drill down to see parts and assemblies.
-
—
—
Opinion on going the linear rod route or linear guide rails
Opinion on going the linear rod route or linear guide rails. On my first Eustathios spider build I used the rods and they rusted. I did use 1 to 1 all purpose oil on them. I want to buy as much of my items on cyber Monday as I can. Can anyone give me their two cents? Was i suppose to use lithium, grease instead? +Sonny Mounicou Can you advice?
-
—
—
Really hate to ask as I know it's an easy thing to do, but does anyone have the XY Belt Tensioners and the default carriage modified for use with 10mm cross rods?
Really hate to ask as I know it’s an easy thing to do, but does anyone have the XY Belt Tensioners and the default carriage modified for use with 10mm cross rods?
-
—
—
Greetings all- I have been lurking and browsing for a bit trying to absorb as much as I can before starting my build
Greetings all-
-
—
—
Alright, this has really stumped me... If my Z is homed my Y won't home and if the Y is the Z won't
Alright, this has really stumped me…
-
—
—
Hi guys, May I ask you a service;
Hi guys,
-
—
—
Hi all, really generic question. Given the boards and motors we are using, is their some software out there that can help us see our print job status as such, I mean our software already counts steps and must know at what
Hi all, really generic question. Given the boards and motors we are using, is their some software out there that can help us see our print job status as such, I mean our software already counts steps and must know at what layer height the part is…ugh I wish I never stopped coding….this would be such a nifty thing to have.But yes the question: is their software readily available to incorporate into our current components (regardless of mobo).: https://www.3d-printerstore.ch/images/product_images/popup_images/13592_5.jpg
-
—
—
I am one of those with a half built printer that is begging to be finished
I am one of those with a half built printer that is begging to be finished. Attempted to “Assemble” my Bed assembly with the Z-axis lead screw over the weekend, and found an issue I’m curious to hear from others about.
-
—
—
Hi all, I'm back live and kicking
Hi all, I’m back live and kicking. Going to take this new build’s nice and slow. Yes building both the Herculien AND Eustathios. Got the proper equipment to build and not under a time constraint. My first question: is PETG a proper plastic to print the parts? I really want the printer to last the high speeds I really really hope to get to. The extremely slow Creality CR-10 is driving me insane. But all be it a good printer. What is the preferred material to print the plastic parts?
-
—
—
Looking to use just a rectangular build plate like Walter's, does anything know what sizes will work without any (or minimal) modification to the design?
Looking to use just a rectangular build plate like Walter’s, does anything know what sizes will work without any (or minimal) modification to the design?
-
—
—
Is there some particular reason the to use the Azteeg X5 GT over the Smoothieboard for the HercuLien?
Is there some particular reason the to use the Azteeg X5 GT over the Smoothieboard for the HercuLien? Does have more power or is there a reason we really need the modular drivers?
-
—
—
I'm ordering up my parts for my build and I'm stuck deciding between 8mm and 10mm rods for the gantry
I’m ordering up my parts for my build and I’m stuck deciding between 8mm and 10mm rods for the gantry. Is there any downside to moving to 10mm? If I wanted to attempt direct drive I know it’s recommended, and I am having trouble sourcing the 8mm bronze bushings anyways so unless I’m missing a negative, it seems like it’d be maybe easier to just go with 10mm. I’m just concerned there’s a negative that I’ve missed.
-
—
—
Had a print fail on me this weekend due to my Bowden tube between extruder and hotend popping out from the bondtech side
Had a print fail on me this weekend due to my Bowden tube between extruder and hotend popping out from the bondtech side. Considering all the problems I’ve had tuning the bowden I am considering switching to the Bondtech BMG. +Eric Lien I saw you posted a new carriage for that. How was the experience?
-
—
—
Had anyone tried out a remote direct drive extruder such as the Flex3Drive or Zesty Nimble?
Had anyone tried out a remote direct drive extruder such as the Flex3Drive or Zesty Nimble?
-
—
—
Not the most pleasant surprise powering on my Azteeg X5 GT :( I followed all the instructions and all wires were perfect
Not the most pleasant surprise powering on my Azteeg X5 GT :(
-
—
—
And now that she is pretty much done, here is a Marvin at 500%
And now that she is pretty much done, here is a Marvin at 500%. Volcano prints are absurdly strong.
-
—
—
As a PSA, I had a weird issue with my x.y axis surging
As a PSA, I had a weird issue with my x.y axis surging. Its weird to describe, but it would almost pause for half a second, then continue. The steppers weren’t skipping, so it was a bit confusing. I swapped motors, stepping level, digipot levels, etc. but nothing helped. I fixed it by removing the dampers. What would happen is that when the axis got to a sticky spot, it would cause the damper to bend until the motor applied enough torque to overcome it.
-
—
—
Anyone know if I can use the smoothie config posted on the guthub for a X5 GT with Bigfoot BSD2660 drivers?
Anyone know if I can use the smoothie config posted on the guthub for a X5 GT with Bigfoot BSD2660 drivers? I assume I will need to change a few things, but is the config different for the new board (sorry first time on smoothie)
-
—
—
Anyone have a good source for IGUS ECLM 08 bearings?
Anyone have a good source for IGUS ECLM 08 bearings? There site is $40 for 5! (w/ shipping)
-
—
—
Really simple question regarding mosfet driver module for PWM control of cooling fans that have too high of a current for my Azteeg X5mini V3
Really simple question regarding mosfet driver module for PWM control of cooling fans that have too high of a current for my Azteeg X5mini V3. I don’t want to fry anything and wiring is not more forte. My question is primarily focused on the correct signal line, should it be the +5V line from Azteeg into the SIG of the driver module? See horribly drawn image attached.
-
—
—
About to give up on Bowden, running 2 Saitflint's with hobb goblin drive gears
About to give up on Bowden, running 2 Saitflint’s with hobb goblin drive gears. getting abysmal print quality got retraction perfect but theres so many blobs around the print and none of the layers even line up :/.
-
—
—
So I'm finally at a point where I have a working derivative/custom Eust
So I’m finally at a point where I have a working derivative/custom Eust. I’ll have her printing tomorrow. But I thought I’d post some pics tonight. This one has rails for x/y/z. It uses igus bearings for the rods. The bearing supports, the carriage, and the x/y ends are all custom designed CNCed aluminum. The bed is a druckerplate. On the carriage, I’m using a titan extruder with a volcano nozzle. It has a BLTouch mounted behind it. I still need to design endstops, a fan duct, and increment the x/y ends one more time. Oh, and I need to do something with wiring, its a mess.
-
—
—
Does anyone here have a working config file and the latest firmware for the X5 Mini V3 and Eustathios Spider V2?
Does anyone here have a working config file and the latest firmware for the X5 Mini V3 and Eustathios Spider V2?
-
—
—
I'm literally only a week into owning a printer at all, and I'm already thinking about my second
I’m literally only a week into owning a printer at all, and I’m already thinking about my second.
-
—
—
Hello, I'm back! Currently running the Azteeg X3, got a defective one with a bad FET and I am going to update to the X5 GT
Hello, I’m back! Currently running the Azteeg X3, got a defective one with a bad FET and I am going to update to the X5 GT. What drivers to you guys recommend, looking for maximum print quality at 80mm/s to 120mm/s on a Spyder V2 with a Chimera.
-
—
—
Eric Lien I recently started using Simplify3d (it's about time, I bought it months and months ago)
+Eric Lien
-
—
—
The Hybrid. Always had bad z wobble with the increased height, so spent a few hours on the mill and lathe to get the z framework cut down and installed
The Hybrid.
-
—
—
Originally shared by Alex Skoruppa Ray Kholodovsky challenged me to design a which has 4 filament inputs
Originally shared by Alex Skoruppa
-
—
—
Eric Lien I can't seem to find the sldprt files for the spool holders
+Eric Lien I can’t seem to find the sldprt files for the spool holders. The 50mm ones were perfect for my petg spools, but the 32 mm ones are 10mm too short for the pla spools I have. Are they in one of the zip files for the other formats?
-
—
—
I'm getting this noise only when moving in Y at low speeds
I’m getting this noise only when moving in Y at low speeds. It’s kind of like a chatter/binding sound, but I cant figure out where its coming from, it vibrates the whole machine… any hints? Should I add a little light oil to the rods?
-
—
—
First layer, first print! PETG 60MM/S .2 layer height
First layer, first print! PETG 60MM/S .2 layer height.
-
—
—
200mm/s no Z break in
-
—
—
100mm/s no Z break in
-
—
—
IT'S ALIVE!!!! getting ready to run the first break in code, but so far no binding or chattering!
IT’S ALIVE!!!!
-
—
—
Powered up my radds board today to heat up the hotends for tightening, and on first power up popped the capacitor under the E1 driver, letting out a fair bit of magic smoke in the process
Powered up my radds board today to heat up the hotends for tightening, and on first power up popped the capacitor under the E1 driver, letting out a fair bit of magic smoke in the process. Board seems to be ok otherwise, do you think I can switch to E2, or should I just bite the bullet and replace the board?
-
—
—
Ran into a little issue with the chimera/cyclops carriage
Ran into a little issue with the chimera/cyclops carriage. It doesn’t hang down anywhere near as low as the original carriage, so there’s nowhere good to mount the z endstop for z-min. I switched to z-max, so not a huge deal (it’s also how my current printer is set up, so I’m used to waiting for the homing sequence), but something to be aware of.
-
—
—
Ok, we're down to pretty much wiring ;) For those of you running boards that are capable of 128 microstepping, what are you running at on each axis?
Ok, we’re down to pretty much wiring ;)
-
—
—
Is there a list of steps to getting started?
Is there a list of steps to getting started? I like that there’s a lot of custom work going on, but from the little bit I’ve read are some of the custom parts better to use the official parts? Right now I’m just going down the list of STL files, looking at the picture to see how many I need to print, and moving on to the next one. I’ve got a Tantillus that’s (mostly) going strong but I’m a little confused on how to print the carriage. The version that says it has built in supports has a gap between the base under the hanging part and the carriage itself. I’m assuming I’ll need to turn on supports and it will fill in there as needed, but will my slicer (KISSlicer) add supports as needed to the non-built-in support one? I’m printing in PLA.
-
—
—
Eric Lien (Or anyone else who might have a minute), could you please post pictures of your x, y, and z endstop mounts on your Herculien?
+Eric Lien (Or anyone else who might have a minute), could you please post pictures of your x, y, and z endstop mounts on your Herculien? I couldn’t find a clear shot of them in Github or here….
-
—
—
Ok, Little help... I'm starting to put together the x and y axes on the herculien, and my ten mm bearings are tight, but slide on the 10mm rod fine, the bushings are the same, and the 32 tooth gears go on just fine
Ok, Little help… I’m starting to put together the x and y axes on the herculien, and my ten mm bearings are tight, but slide on the 10mm rod fine, the bushings are the same, and the 32 tooth gears go on just fine. The 10mm shims, however, will not fit on the rods. I tried running a 10mm drill through a couple, but it didn’t help.
-
—
—
coming along. A couple of tips: 1) when you order the silicon heater, specify you want the wires offset from the centerline
coming along. A couple of tips:
-
—
—
Shared on June 09, 2017 21:57...
-
—
—
I've just fried my Smoothieboard when one of the cables (hotend temp) came loose during printing (it must have connected with GND or another cable)
I’ve just fried my Smoothieboard when one of the cables (hotend temp) came loose during printing (it must have connected with GND or another cable).
-
—
—
Hey, question: Has someone already modified to fit the Eustathios?
Hey, question:
-
—
—
The last time this happened was 39 weeks ago when I posted a picture of my broken boro glass on here
The last time this happened was 39 weeks ago when I posted a picture of my broken boro glass on here. Only this time I don’t have a spare piece. These pieces are sticking so well that when they cool, the PLA pulls the glass with it. I shouldn’t complain since this piece of boro glass lasted 39 weeks, but what a bummer.
-
—
—
Now it feels like we're making some progress!
Now it feels like we’re making some progress!
-
—
—
What is everyone printing the Herculien parts out of ABS, PLA, or other?
What is everyone printing the Herculien parts out of ABS, PLA, or other? I have been playing with some eSun PLA+ and seems really good results.
-
—
—
Well, the lid is done (still got the door to do)
Well, the lid is done (still got the door to do)
-
—
—
quick question on the herculien, how useful is the door on the lid vs just lifting the lid up?
quick question on the herculien, how useful is the door on the lid vs just lifting the lid up?
-
—
—
Finally installed Walter Hsiao 's Mini Space Invaders Carriage with 40mm Fan
Finally installed +Walter Hsiao’s Mini Space Invaders Carriage with 40mm Fan. The bushings from my original carriage got loose an fell off during a print so I installed the carriage that has been half finished for quite some time. It’s printed in ASA-X. This carriage is higher than the original, therefore I had to modify the Z-axis support to allow the bed to reach the nozzle (one screw head touched the Z-shaft mount). I might redesign the Z-end stop switch mount as it had to be twisted to move up the switch high enough. Part cooling fans are ordered. Does anyone know how they are fixed? Glue?
-
—
—
Eric Lien I'm probably just being blind again, but I can't seem to find the printed part stl / files for the slider thingy that keeps the lid from falling over backwards, and I noticed that in the new pictures in the repo
+Eric Lien I’m probably just being blind again, but I can’t seem to find the printed part stl / files for the slider thingy that keeps the lid from falling over backwards, and I noticed that in the new pictures in the repo you’ve replaced that with a metal folding thing (I don’t know what that type of hinge is called)… do you have a part number/vendor for it? Thanks!
-
—
—
quick mod on the Herculien. The Meanwell 350 watt power supply has different dimensions than the 450, and the power lugs face the wrong way
quick mod on the Herculien. The Meanwell 350 watt power supply has different dimensions than the 450, and the power lugs face the wrong way. The lower brackets in the bom work fine, but the upper one doesn’t fit I added two printed brackets for the top, and some extrusion on the frame to create a cutout for the power supply and a place to attach the upper brackets. There’s an extra upright in there that acts as a slider so that I can put a small peice of lexan to protect the lugs, but still provide airflow to the fan and vents on the power supply. Here are some pics, I’m planning to write it up and submit a pr for the community mods.
-
—
—
Getting an Azteeg X5 GT wired in to my printer
Getting an Azteeg X5 GT wired in to my printer. Everything is done but the fans.
-
—
—
So frustrated... printed about half of my parts in petg and was printing the carriage...
So frustrated… printed about half of my parts in petg and was printing the carriage… about halfway through, Marlin crashed and restarted. Restarted the print, and it did it again. The second time, I forgot to turn the heat on before homing and it pulled the bed out of whack. Got that sorted, releveled the bed, and printed the carriage over usb. Next thing I went to print (xy tensioners), bed was out of level again. Re-leveled the bed and now ‘ve been trying to resume printing for three days and the petg won’t stick to anything but the nozzle regardless of z height. AAARGH!
-
—
—
Here is the first print off my recently completed Eustathios
Here is the first print off my recently completed Eustathios. Pardon the length (too long) and production quality (not my forte). Thanks again to +Eric Lien and this community in general.
-
—
—
First of all, thanks Eric Lien , and the rest of this community for being such a great place
First of all, thanks +Eric Lien, and the rest of this community for being such a great place. I’ve been a passive participant for a few months, but I’ve learned a lot just reading. That said, I have run into an issue on my first Eustathios build…
-
—
—
Small update: I received my second ball screw and finallized the mechanical design for the pressure sensitive bed for Z axis calibration
Small update: I received my second ball screw and finallized the mechanical design for the pressure sensitive bed for Z axis calibration. Now i need to create a circuit board for the arduino and mounts to hold the cell sensors.
-
—
—
Does anyone have a lead on the closed loop belts needed for the Herculien?
Does anyone have a lead on the closed loop belts needed for the Herculien? the only ones I can find are at sdp/si and are out of stock until late june :(
-
—
—
A little progress over the weekend... and a shot of the MVP tool for this stage
A little progress over the weekend… and a shot of the MVP tool for this stage. Not a bad investment for $70 at harbor freight….
-
—
—
Huh. Just happened across my google plus page today and thought i'd see if this group was still going
Huh. Just happened across my google plus page today and thought i’d see if this group was still going. Nearly 9000 members! Nice work +Eric Lien :)
-
—
—
I'm not sure if these are at retract or restart locations, but they appear on the print just as advertized on the g-code preview
I’m not sure if these are at retract or restart locations, but they appear on the print just as advertized on the g-code preview.
-
—
—
Hey all. Trying to get PETG tuned properly, finally got past the point of print failure due to blob buildup
Hey all. Trying to get PETG tuned properly, finally got past the point of print failure due to blob buildup. But just can’t quite get these little zits to go away.
-
—
—
Hello, I'm interested in building the eustathios spider v2
Hello, I’m interested in building the eustathios spider v2.
-
—
—
Anyone had problems with their PEI sheets delaminating from the glass?
Anyone had problems with their PEI sheets delaminating from the glass?
-
—
—
Finally getting started on my Herculien build
Finally getting started on my Herculien build. I was planning on building one ~2 years ago, then got sidetracked by a large format printer kickstarter that turned out pretty much as you’d expect. After a few iterations of redesign on that printer, I’ve finally had to admit I should have stuck with the herc ;) As you can see I’ll have plenty of help.
-
—
—
Going mad this afternoon. Been a while since I messed with my Eustathios, yesterday got a PEI sheet laminated to my glass and ran through tramming the bed with the piece of paper and many repetitions method
Going mad this afternoon. Been a while since I messed with my Eustathios, yesterday got a PEI sheet laminated to my glass and ran through tramming the bed with the piece of paper and many repetitions method.
-
—
—
Hello, I have a problem with my eustathios V2, the mouvement of my XY axis isnt smooth and I think my axis are not perpendicular
Hello,
-
—
—
Hey guys. This'll be my first 3d pro yet build as well as my first post
Hey guys. This’ll be my first 3d pro yet build as well as my first post. I have decided to build a Eustathios with a fairly large volume (roughly 222ft cube) and I have some questions regarding the build.
-
—
—
Starting to look like a printer
Starting to look like a printer
-
—
—
So... has anyone incorporated an inductive sensor into the carriage for this family of printers?
So… has anyone incorporated an inductive sensor into the carriage for this family of printers? I have an aborted rebuild of my large printer and really need to tear it down and take care of those issues, and while doing so, incorporating mesh bed levelling (based on my Prusa MK2 experiences) will be a necessity.
-
—
—
Hey Guys, i know some of you like to see the new printer beeing built so here are some pictures of my current state
Hey Guys, i know some of you like to see the new printer beeing built so here are some pictures of my current state.
-
—
—
I was wondering if there was anyone in the UK who would be so kind to print me all the parts for the Eustathios v2 (With some slight changes) I'm willing to pay (as long as its reasonable) but it would go a long way to
I was wondering if there was anyone in the UK who would be so kind to print me all the parts for the Eustathios v2 (With some slight changes) I’m willing to pay (as long as its reasonable) but it would go a long way to restoring my sanity.
-
—
—
Hey all, just a quick note that I uploaded an "Improved Eusthathios Spider 2 adjustable Z stop" at: This one now has two screws (instead of one) to the extrusion to help keep it more stable
Hey all, just a quick note that I uploaded an “Improved Eusthathios Spider 2 adjustable Z stop” at: https://www.youmagine.com/designs/improved-eustathios-spider-v2-adjustable-z-stop
-
—
—
The build plate of Eustathios is relatively large, I'm thinking using a drag chain on XY plane to guide the electric cable for the extruder
The build plate of Eustathios is relatively large, I’m thinking using a drag chain on XY plane to guide the electric cable for the extruder. I’m hoping doing that may help ease the tension on the extruder. If any one using or interested in a setup like that, please share some experience.
-
—
—
I'm starting to print all my parts today and noticed the Belt Tentioners in the Github repo look different compared to what everyone is using
I’m starting to print all my parts today and noticed the Belt Tentioners in the Github repo look different compared to what everyone is using. I am using 10mm press fit brass bushing.
-
—
—
I have uploaded the model files for a direct drive carriage for the Eustathios
I have uploaded the model files for a direct drive carriage for the Eustathios. Hope you guys can have some fun with it.
-
—
—
I posted this pic over at the 3D Printing page but thought I'd post here too
I posted this pic over at the 3D Printing page but thought I’d post here too. Broke one of the rubber belts last night. The other 3 are the white steel core variety.
-
—
—
Got home today to a nice Little surprise
Got home today to a nice Little surprise. Thx +Brad Hill and +Patrick Woolfenden for the amazing little printer, even the wife gave me a Aww for the size of the printer. #KittenPrinter
-
—
—
I guess I won't have the time to try this Titan Aero thing out quickly but I was nosey if it could work so I fired up Fusion360 quickly this morning and gave it a quick sit
I guess I won’t have the time to try this Titan Aero thing out quickly but I was nosey if it could work so I fired up Fusion360 quickly this morning and gave it a quick sit.
-
—
—
Thanks for your help and the discussion on how to wire up an Eustathios at MRRF Eric Lien .
Thanks for your help and the discussion on how to wire up an Eustathios at MRRF +Eric Lien. As I mentioned I was going to put together a wiring diagram to confirm that I have my wiring layout understood and “accurate.” I’m almost to the wiring portion of my build. Look forward to the feedback.
-
—
—
Kinda like christmas today :) What also arrived today was my Titan Aero from E3D Online
Kinda like christmas today :) What also arrived today was my Titan Aero from E3D Online. The motors from OMC-Steppersonline already came a few days ago. The one I ordered (http://www.omc-stepperonline.com/nema-17-bipolar-step-motor-29v-07a-18ncm255ozin-17hs100704s-p-260.html) actually only weigs in at 145g and not 180g as advertised. The Titan Aero comes at around 255g which makes this a 300g direct extruder.
-
—
—
After 3 weeks of waiting I received my SDP/SI order today (they shipped after around 8-10 days, the remaining time went into shipping and customs clearance)
After 3 weeks of waiting I received my SDP/SI order today (they shipped after around 8-10 days, the remaining time went into shipping and customs clearance). Quite an expensive stunt. Their intl. shipping is expensive, given the small package and weight so i paid a little under $100 for everything including import tax. I ordered 10 x 10mm and 6 x 8mm to have a few in spare.
-
—
—
Has anyone yet tried a 3mm bowden on the Eusthatios?
Has anyone yet tried a 3mm bowden on the Eusthatios? I wonder what it’s like? Pros and Cons?
-
—
—
Hey guys, getting ready to replace my aging kossel mini with a eustathios, but I had a quick question
Hey guys, getting ready to replace my aging kossel mini with a eustathios, but I had a quick question. Has anyone been successful downsizing this build to something work perhaps about a 200x200mm print area? Looking for something that’s between a kitten printer and the eustathios size. Thanks guys! Really love the active community around this design!
-
—
—
I would like to thank the work that Eric Lien has developed, to thank you even more for sharing your knowledge with us all
I would like to thank the work that Eric Lien has developed, to thank you even more for sharing your knowledge with us all. You have created a community far beyond the horizons of the State of Minnesota.
-
—
—
Hey everyone. Printing on my Eusthatios is getting better as my hotend cooling is fixed now
Hey everyone. Printing on my Eusthatios is getting better as my hotend cooling is fixed now. I’m actually quite happy in terms of reliability and general printing but on closer look and on brighter materials like this white PLA I do see some marks. They seem to be running around the whole object so they shouldn’t be due to some play in my carriage.
-
—
—
Hey guys, how are you wiring your fans?
Hey guys, how are you wiring your fans? I have my heatsink fan going to the 24V directly from the PSU, but then it stays on all the time. I’m new to marlin configuration and I’m having trouble setting pins and getting them to work in S3D. I have an Azteeg X3 (with shield) that came with a defective HBed FET so I set #define HEATER_BED_PIN 17 to put that on the Ext 3 spot. I have my print fan on E4 (#define FAN_PIN 16). I can run GCode to turn these on in S3D, but how do I link them to the HBED and fan control?
-
—
—
What's wrong with this picture (video)? Bushing fell out mid-calibration cube - I thought the holes tight enough, they were light press fit...
What’s wrong with this picture (video)?
-
—
—
E3D might have released that last bit that I needed to give direct extrusion some try on a Eusthatios like machine
E3D might have released that last bit that I needed to give direct extrusion some try on a Eusthatios like machine. :)
-
—
—
Figure this might be a good place to post this, anyone looking to add a printer kitten to their collection?
Figure this might be a good place to post this, anyone looking to add a printer kitten to their collection? I had Patrick build one up for me but I’m just swimming in printers. Only changes made have been swapping out the titan for bondtech mini, changing the firmware steps and printing out the gold benchy pictured. Would love it if someone had a use for it :) I’m happy to let it go for a good price, was thinking $495. I’m not sure what the state of the project is, but the github stuff is all still there. It’s the printer from this post: https://plus.google.com/105660857457447815256/posts/aT1mzr7Knmj
-
—
—
I have a brand new Azteeg X5 Mini V3 with SD6128 drivers that I will let go for $100 shipped if anyone is looking for a controller
I have a brand new Azteeg X5 Mini V3 with SD6128 drivers that I will let go for $100 shipped if anyone is looking for a controller. I’ve mounted the heat sinks to the drivers but never even powered the board on.
-
—
—
is there a Single or Dual hotend carriage for either the herculien or eusthanios and variants that have a spot for a barreltypes/threaded probe?
is there a Single or Dual hotend carriage for either the herculien or eusthanios and variants that have a spot for a barreltypes/threaded probe? specifically this or similar size
-
—
—
500 mm/s ;) :
-
—
—
Looks like I managed to solve my long lasting problem by just adding some thermal grease
Looks like I managed to solve my long lasting problem by just adding some thermal grease. I’m a bit buffled how big the difference is but all that glogging/jamming I had before seems to be gone. At least with the first test which is the PLA that caused me the biggest problems so far. This print isn’t perfect yet but that needs just a little bit of temp tuning I guess. Amazing to see that the new carriage seems to work better than I thought without the extrusion chaos.
-
—
—
So looks like I did in fact spend the Weekend in the workshop trying to get my Eusthatios running
So looks like I did in fact spend the Weekend in the workshop trying to get my Eusthatios running. Overall it hasn’t all gone bad but at the end the frustration isn’t really any lower than before ( see last comment under this one: https://plus.google.com/+FrankHelmschrott/posts/gDhNkJBJM2J).
-
—
—
What is the build volume of the HercuLien?
What is the build volume of the HercuLien? I keep googling around and cannot find a number written in stone or on the GitHub repo. Just that it has a “large build volume”. Thanks! :)
-
—
—
Hey, I've had my Azteeg X3 have the heated bed always be powered on
Hey, I’ve had my Azteeg X3 have the heated bed always be powered on. I try to turn it off through the Viki to no avail. The light is on and the ssr is flipped on. The light would always be on, even when I got the board with its pre-loaded firmware. Defect?
-
—
—
Eric Lien do you have CAD models for the Cohesion Remix?
+Eric Lien do you have CAD models for the Cohesion Remix? Mounting brackets etc?
-
—
—
I've never really participated in social media on my 3D printing adventures
I’ve never really participated in social media on my 3D printing adventures. So this is a bit new to me. I’ve built about 6 3D printers some got disassembled and built(are being built) into new printers.
-
—
—
Is there any reasonable way to independently control more then two fans from an Azteeg X5 mini v3?
Is there any reasonable way to independently control more then two fans from an Azteeg X5 mini v3?
-
—
—
Im on the hunt for perfect prints
Im on the hunt for perfect prints. I’ve had issues since I’ve started using my Eustathios where I get minute position errors which translate into irregularities on the side walls and holes that aren’t always perfectly circular.
-
—
—
Anyone else having lockups on their Azteeg X5 ?
Anyone else having lockups on their Azteeg X5 ? I’ve had several and it’s starting to tick me off, 24hrs into a 30hr print and it’s wrecked. Happens randomly, sometimes it’s once a week, then it won’t happen for a month.
-
—
—
I just wanted to take a quick survey of the group: what plastic are you using to print your parts?
I just wanted to take a quick survey of the group: what plastic are you using to print your parts? PLA? ABS? Other?
-
—
—
I think I finally may have figured out my circles not being circular issue...
I think I finally may have figured out my circles not being circular issue… It appears one of the bushings is sloppy as all hell… See the video below (sorry for the quality) and it looks like it is moving back and forth. Has anyone seen this before? The only thing I can think is that I wore it open when using a drill to get the carriage to slide smooth. I am still surprised it’s this loose though. I guess the only fix is to buy a new bushing. Any advice?
-
—
—
Want to Sell all my Eustathios v2 Parts (including everything to finish this 3D printer, I don't want to sell them separately) And I only finish the frame part....
Want to Sell all my Eustathios v2 Parts (including everything to finish this 3D printer, I don’t want to sell them separately) And I only finish the frame part…. so you need to put other parts together ~~ If anyone is interested, pls let me know : supremeoape@gmail.com
-
—
—
Hey guys. What are you doing for extruder mounting on the Spider V2?
Hey guys. What are you doing for extruder mounting on the Spider V2? I’m using dual saintflints, and want to keep the tube as short as possible (I plan to do something like the herculien later and have an enclosed chamber with extruders mounted at the top.) Anyone have stls for a stepper clamp that works?
-
—
—
Finally done with my box variant of the Eustatihios
Finally done with my box variant of the Eustatihios. Works very well, but i still have som fine tuning to do. I went with igus self aligning bearings and I can only say good things about them..
-
—
—
Does anyone have an x/y axis belt tensioner bearing block that will fit my flanged self centering sintered bushings
Does anyone have an x/y axis belt tensioner bearing block that will fit my flanged self centering sintered bushings. They are for 10mm rod and have an OD of 16mm.
-
—
—
Question, what would people recommend for increased Z height (500 mm), is it feasible to extend the Eustathios, or rather Herculien?
Question, what would people recommend for increased Z height (500 mm), is it feasible to extend the Eustathios, or rather Herculien?
-
—
—
Last night I dry run my Eustathios, It went well, the printer working at 32 micro stepping, produce much lower level of noise than my direct extruder linear ball bearing CoreXY printer( noise in the video is from my coreXY
Last night I dry run my Eustathios, It went well, the printer working at 32 micro stepping, produce much lower level of noise than my direct extruder linear ball bearing CoreXY printer( noise in the video is from my coreXY printer at a few meter away). I use lower spec step motor on X and Y axis, they run cold at 200mm/s travel rate. And I use light switch on the Z endstop, the well planned aluminum extrusion frame design really make life easier.
-
—
—
Hey all. I just started building my Eustathios and I have a couple questions
Hey all. I just started building my Eustathios and I have a couple questions. I have been using my own variation of the Prusa I3 for a while now and I have a touch probe for auto bed leveling. There are a few things I don’t like about it and I have seen a lot of people using the proximity sensors and I think I want to use that on my new build instead of the touch probe. What is a good one to use and will they work with an aluminum bed with glass over it? also trying to source some good but inexpensive ball screws or lead screws and nuts. Also what is everyones take on ball screw verses lead screw pros and cons. really looking forward to having a printer where the bed only moves up and down. I’m thinking I might be able to get better prints with this design. Any help is appreciated. TIA
-
—
—
My Eustathios Spider came to life in mid-January!!
My Eustathios Spider came to life in mid-January!! TLDR: All worked well and several mods have panned out, all is owed to this community.
-
—
—
IT. IS. ALIVE..... No endstops, steps per mm not perfect, heaters not wired, lots more to do - but after my second attempt at aligning the cross rods, I've got the XY burn-in gcode running at just .5 Amps (non-high torque
IT. IS. ALIVE…..
-
—
—
Finally getting around to posting my most recent updates to my Herculien
Finally getting around to posting my most recent updates to my Herculien. I’ve made 2 major updates:
-
—
—
I am curious as to where everyone is getting their 345mm x 360mm Borosilicate glass for bed?
I am curious as to where everyone is getting their 345mm x 360mm Borosilicate glass for bed? I have not been able to find a piece even close to the size. Comments? Sources?
-
—
—
Eric I need your expertise, hope you can help
Eric I need your expertise, hope you can help. I have designed a core xy system but I am having trouble with layer shifting and print surface ossicillation at speeds beyond 50mm/s … my system uses two separate belt lengths on different planes .. so not a single belt that crosses in the back. I also wonder what should my belt tension should be. Also what are the best tips you could offer to me to help me double check my design. I will post some pictures shortly for review. Thanks very much for any help you or anyone else could provide.
-
—
—
Been a while. My printer has been out of action but today found the time to get it up and running again
Been a while. My printer has been out of action but today found the time to get it up and running again. Have spent the day considering the great “Flying Extruder” modification since I think I’ve just about had enough of long Bowden. +Walter Hsiao what length did you cut the stepper supporting extrusions to? And could you point me to the files for the bondtech mount and the little stem to support the small Bowden? I have put together something similar to your 2020 pivots using the vitamins I had on hand, just need to print the mount and try it out.
-
—
—
The new carriage is just printing its first layers and it not only looks quite nice but moves quite nice too
The new carriage is just printing its first layers and it not only looks quite nice but moves quite nice too. I’m happy how this turned out. Didn’t think that my first printed version of the new carriage would fit instantly in all terms - even with the clips for the +igus Inc. ECLM bushings.
-
—
—
Up until this point I have been using a 1kW 120VAC silicone heating pad for my Herculien with 2 thermistors as specified in the BOM
Up until this point I have been using a 1kW 120VAC silicone heating pad for my Herculien with 2 thermistors as specified in the BOM. I recently decided to replace the aluminum heat spreader with an actual flat plate and noticed some burns on my heater. Since I didn’t want to continue with a potential fire hazard, I decided drew up some new heater specification with some input from +Eric Lien.
-
—
—
Just received the samples from igus Inc
Just received the samples from +igus Inc. today and put them straight into my first print. Fits quite nice and feels great though they have a little bit of play. At the end its still less than I had with the LM8LUU before. It’s really hard to get some good ones of these linear ball bearings.
-
—
—
Last night one of my stepper motors died in the middle of a print
Last night one of my stepper motors died in the middle of a print. The back bearing had gotten completely stuck and when I took it out it was full of brown-ish powder that looked a little like rust, but I think it might have been dried grease.
-
—
—
Just finished drilling the 2020. Before I started the build I was afraid this part would be a bit challenging
Just finished drilling the 2020. Before I started the build I was afraid this part would be a bit challenging. I used 6mm drill bit, two 6mm bearing, (four will be ideal), and a printed Guide. I had to pressing the bearing down so that they won’t pop out when working, should find a way to fix the bearing along Z axis.
-
—
—
We have an Ultimaker 2 and work
We have an Ultimaker 2 and work. I am itching to have my own 3D printer at home.
-
—
—
Any one have any suggestions for the 8mm Bronze Bushing for the Eustathios, searched everywhere and seems noboddy has them in stock?
Any one have any suggestions for the 8mm Bronze Bushing for the Eustathios, searched everywhere and seems noboddy has them in stock?
-
—
—
I had a lot of fun building my Eustathios!
I had a lot of fun building my Eustathios! Thanks a lot +Eric Lien for publishing the files and creating that community here. To give some feedback, I like to show some pictures and a video of my modded printer. Most of my modifications were motivated to reduce cost or/and to reuse stuff. Just my final carriage is a modification worth mentioning:
-
—
—
Just wanted to share my development in terms of new Extruder Carriage for the Spider V2
Just wanted to share my development in terms of new Extruder Carriage for the Spider V2.
-
—
—
Last prints and ASA filament test. The Eustathios handled it nicely
Last prints and ASA filament test. The Eustathios handled it nicely. It will be my go-to filament for outdoor use. Bye smelly ABS !
-
—
—
Hi Community, i'm from germany. Can i buy Eustathios Spider V2 as KIT?
Hi Community,
-
—
—
Hey Eric Lien could you help me find the right part number for the the lead screws, seems MTSBRB12-425-S46-Q8-C3-J0 is no longer valid
Hey +Eric Lien could you help me find the right part number for the the lead screws, seems MTSBRB12-425-S46-Q8-C3-J0 is no longer valid.
-
—
—
Just wondering if anyone is using the Eustathios in a dual extrusion setup
Just wondering if anyone is using the Eustathios in a dual extrusion setup. I’ve never tried, but am keen to give it a go.
-
—
—
Hi peeps, Just upgraded to a DuetWifi (Thanks for the advice, its a wicked board) and I purchased the IR probe to go along with it
Hi peeps,
-
—
—
I'm searching for inspiration, guys. I wonder what carriages you guys are using except from the standard one
I’m searching for inspiration, guys. I wonder what carriages you guys are using except from the standard one. I’m missing motivation and creativity lately and already spent some hours drawing and throwing away ideas. My last design was based on the one from +Walter Hsiao which basically was great but failed at cooling the E3D in the right way. Also the mounting of my special kind of Bed Level Sensor (the small IR sensor) wasn’t that good. I liked the dual blower setup for part cooling and I thought it would be worth keeping it.
-
—
—
Do you know some PLA pack of 1 Kg with good price/quality ?
Do you know some PLA pack of 1 Kg with good price/quality ?
-
—
—
Hey everyone. Does anyone know of a good European Source to get these pushfit (self aligning) bushings that are used in the original Eustathios design?
Hey everyone. Does anyone know of a good European Source to get these pushfit (self aligning) bushings that are used in the original Eustathios design? I switched to graphite bushings from Robotdigg first and am now using LM8LUU for the center (carriage) but I’m not happy with the play of the latter. I’d like to give the original ones a try as I do have to redesign my carriage anyways (still for cooling issues).
-
—
—
Greeting, I join the group recently. Now I'm planing to sourcing the parts for my build of Eustathios Spider V2
Greeting, I join the group recently. Now I’m planing to sourcing the parts for my build of Eustathios Spider V2. While my build will stick to the plan most of the parts, I wonder if upgrade the Z Axis timing belt to 2GT-10mm will gain any advantage? Or is it just a waste to upgrade it? Thanks.
-
—
—
Hey guys! I'm running the break in gcode but its only operating in the 1st quadrant of the bed
Hey guys! I’m running the break in gcode but its only operating in the 1st quadrant of the bed. Any ideas? I haven’t made a S3D profile yet, but if someone would send me one as a starting point it would be greatly appreciated :)
-
—
—
Eric Lien if I wanted to upgrade my Azteeg x5 v3 to something that could drive up to three extruders, whats my best option for a smoothly based board?
+Eric Lien if I wanted to upgrade my Azteeg x5 v3 to something that could drive up to three extruders, whats my best option for a smoothly based board? I know Panucatt has produced a new board (x5 GT), but its out of stock and it’ll only run two extruders?
-
—
—
I just finished up building this Printer Kitten
I just finished up building this Printer Kitten. This one got an E3D Titan. The Bondech is still my favroit extruder though. A 3Dbenchy as the first print. Polymaker Poly Plus, 0.1mm layer height
-
—
—
Ok, real first print this time. I must say, I'm really impressed with this design
Ok, real first print this time.
-
—
—
First print time! I finally got everything wired up, and it works!
First print time!
-
—
—
Today I started putting together a Printer Kitten for Brad, a friend of mine
Today I started putting together a Printer Kitten for Brad, a friend of mine. I made some pretty good progress tonight and hope to have it finished up by Tuesday.
-
—
—
OK, I've put off ordering parts long enough and I need to get a new printer started
OK, I’ve put off ordering parts long enough and I need to get a new printer started. My only hesitation is that I want to go as large as possible but I’m not sure what the limits of this style of printer would be. Maybe i’m better off looking at a different design? Any suggestions?
-
—
—
Hi, I'm new in this amazing group and I'm building a printer
Hi,
-
—
—
I started with a rework for all the printed parts in Fusion 360
I started with a rework for all the printed parts in Fusion 360.
-
—
—
Question for those in the know or tried it
Question for those in the know or tried it. Would the Eustathios be a good candidate for using a direct drive extruder so that ultra flexible filaments could be used or is that a bad idea on the Eustathios?
-
—
—
Hey Guys, Just wanted to share a couple of my recent prints
Hey Guys,
-
—
—
I will be giving a tutorial of how I align the gantry on a Cross Rod XY Gantry style printer
I will be giving a tutorial of how I align the gantry on a Cross Rod XY Gantry style printer. Examples of this style motion platform are the Eustathios and HercuLien 3D printers. I will be purposely misaligning my Eustathios printer, then I will walk through the process to get things back into alignment.
-
—
—
Figure I should post something I have been testing for a few months now
Figure I should post something I have been testing for a few months now. My Eustathios has always printed great for me. But there was one problem… Every once and a while Z-ribbing would rear it’s head. Not bad by any means… but faintly there and it bugged me. Something to note is that my printer is a Eustathios 1.5V (not quite an original +Jason Smith version, but not upgraded with the extra Z-height, 608 lead screw support bearings, and ball screws of the V2).
-
—
—
Help! I am really stuck with my printer
Help! I am really stuck with my printer. I have reprinted all the parts from PETG and spent hours heat fitting the bearings in the plastic while it was on the rod. Everything seemed perfect, I could blow the mount from side to side on the rod. Then I put everything on the printer, used to spacers to space the pulleys off, tensioned all the belts exactly the same, first pretty tight, the really loose. I loosened the set screws on the belt pulleys then used the alignment thingys to make everything true. It take around 5in lbs of force to turn the pulley where the stepper connects to without the stepper on it. The stepper wont budge it (obviously). What am I doing wrong? Is it possible that someone could facetime me or give me advice? I spent 4 total hours doing the carriage this time, and everything felt just right until I assembled it all. I’m thinking about buying the same bushings that +Walter Hsiao used on his build. I am using my cleaned of design of Eric’s Chimera carriage. I can push the carriage around with my hand, but it takes allot of force.
-
—
—
I built the Eustathios printer, but stretched made it with twice the z build height
I built the Eustathios printer, but stretched made it with twice the z build height. I’m now getting z wobble and was thinking of converting to using v slot like the HercuLien. Has anyone done this before, any advice on converting?
-
—
—
OK, so the member requests per day is getting so high that something must be done
OK, so the member requests per day is getting so high that something must be done. At 30+ a day and growing it is taking me far to long to review each one and confirm they are not just spammers, bots, etc. The majority of the requests are unfortunately not real people, so the ratio of time I spend reviewing profiles to the quantity of new members is lopsided.
-
—
—
Hi all, I recently destroyed my Rambo board so I am looking at buying a replacement
Hi all,
-
—
—
Another "set of hardware" in hopes of one day becoming a real printer
Another “set of hardware” in hopes of one day becoming a real printer. Eustathios on the way.
-
—
—
So we have over 1000+ Members in our fun little group now
So we have over 1000+ Members in our fun little group now. Which I guess means it is not a little group any more. With that in mind I wanted to do something I have thought about for a long time. I want to get a list going of all the builders. Some times I lose track of just how many people have actually built one of these style printers.
-
—
—
I am pouring through the wealth of knowledge here in this community, haven't yet found this answer, so I am throwing it out to you guys...: Can I increase the Z height of the Spider V2 simply by purchasing longer smooth rods,
I am pouring through the wealth of knowledge here in this community, haven’t yet found this answer, so I am throwing it out to you guys…: Can I increase the Z height of the Spider V2 simply by purchasing longer smooth rods, ball screws, and extrusions? If so, I want to increase Z height by 75mm.
-
—
—
What inductive sensors is everyone using? comment below with links please!
What inductive sensors is everyone using? comment below with links please! :D
-
—
—
So I think I've talked about late night dumb moves recently, and I think I just pulled another
So I think I’ve talked about late night dumb moves recently, and I think I just pulled another.
-
—
—
Thank you for adding me! I am recently into 3d printing, about 3 months ago, and hooked
Thank you for adding me!
-
—
—
Hey guys. I know some of you were interested in the Cohesion3D ReMix that I've been working on (and one of you already purchased, thanks Luis)
Hey guys. I know some of you were interested in the Cohesion3D ReMix that I’ve been working on (and one of you already purchased, thanks Luis).
-
—
—
Thought I should share this here too
Thought I should share this here too.
-
—
—
It's Alive! This is my first time running through the break-in Gcode - it's a lot smoother than I expected, although far from perfect
It’s Alive!
-
—
—
Question for the group. Until recently all the invite requests to the community have been slow and steady, as well as very clearly people actually interested in 3DP and this family of printers
Question for the group. Until recently all the invite requests to the community have been slow and steady, as well as very clearly people actually interested in 3DP and this family of printers. But in the last month I have been seeing 30+ a day requests for joining. Most are Middle Eastern or Asian profiles with zero posts, or posts with nothing to do with anything maker at all. I like to be open and inviting… But also want to avoid spam posts or fake community member counts.
-
—
—
For anybody who doesn't already check out from time to time you are missing out
For anybody who doesn’t already check out thrinter.com from time to time you are missing out. It is an amazing blog by +Walter Hsiao. I just noticed he posted an overview of all of his great upgrades to the Eustathios. Check it out, and the rest of his posts. He has a great series on filaments, and also smoothieware tweaks that are certainly worth reading through.
-
—
—
I have a question that has been nagging me
I have a question that has been nagging me. I am looking for a filament drying solution that I saw recently..It can be printed and attaches to an individual roll, then you slide in a strip of plastic to contain the roll and pop in a bag or two of silica gel. Has anyone seen this or can point me in the right direction?
-
—
—
Just wanted to post about Re-ARM for RAMPS for those who weren't aware of it
Just wanted to post about Re-ARM for RAMPS for those who weren’t aware of it.
-
—
—
Anyone have a design for the standard herculien Of the part cooling fan shroud/guide?
Anyone have a design for the standard herculien
-
—
—
hey guys .. im looking for the printhead on this video
hey guys .. im looking for the printhead on this video. Does anyone know where to find the stl ????
-
—
—
I'm seeing a bit of an oddity and wondering if anyone else has seen this?
I’m seeing a bit of an oddity and wondering if anyone else has seen this? I have my suspicions but will wait to see what others respond with.
-
—
—
hey everyone does anyone have a Eustathios carriage that features a direct drive extruder instead of bowden?
hey everyone
-
—
—
With both lead-screw/ballscrews being driven from the same motor, can the cross-beam of the Z-axis (HFSB5-2020-321-TPW) be eliminated?
With both lead-screw/ballscrews being driven from the same motor, can the cross-beam of the Z-axis (HFSB5-2020-321-TPW) be eliminated?
-
—
—
Slowly starting to get back into this project (Spider V2, Azteeg X5) after abandoning it for about a year
Slowly starting to get back into this project (Spider V2, Azteeg X5) after abandoning it for about a year. I got everything built mechanically, but when it came time to set up the controller and get everything working on the software side, I completely lost focus and shut it down. Anyway, I’m back on it now. Time to get this thing printing.
-
—
—
We could use this to replace the ABS on our printer parts!
-
—
—
I wonder how retracts for you guys work on your Bowden setup?
I wonder how retracts for you guys work on your Bowden setup?
-
—
—
I have made a quick video with Marlin3DprinterTool "Teach yourself to Migrate Marlin Firmware in 24 minutes" Marlin3DprinterTools makes it possible to migrate a working Marlin Firmware to a new version of marlin within 1 hour
I have made a quick video with Marlin3DprinterTool
-
—
—
So here's the missing filament spool holder missing in my last post
So here’s the missing filament spool holder missing in my last post. Shout out to the creator Maxime. Find his post here https://plus.google.com/117610054892104446719/posts/b5PfGWD7yuD?sfc=true
-
—
—
Hey everyone. I though I'll leave a short note and some pics/vids of my bigger maintenance I did during the last days
Hey everyone. I though I’ll leave a short note and some pics/vids of my bigger maintenance I did during the last days. If you remember I posted a few weeks ago that my heated bed died and I had to replace it. As I already had some more maintenance in mind I did that now and did even more than I initially thought.
-
—
—
In addition to the Azteeg X5 GT, looks like Roy also has the sd6128 drivers back in stock
In addition to the Azteeg X5 GT, looks like Roy also has the sd6128 drivers back in stock. These drivers are super smooth and quiet.
-
—
—
I know several of you have asked me when this will be available...
I know several of you have asked me when this will be available… Looks like Roy is taking the preorders now for delivery in December.
-
—
—
Been researching and researching and really want to start building but have some reservations
Been researching and researching and really want to start building but have some reservations. How hard would it be to extend the x and/or y axis to around 18”? Are ball screws for the x and y axis a possibility?
-
—
—
Quick and simple mod for those people that (gasp) want to attach a Wade's gear extruder to a Eustathios:
Quick and simple mod for those people that (gasp) want to attach a Wade’s gear extruder to a Eustathios: https://www.youmagine.com/designs/wade-s-gear-extruder-attachment-for-eustathios#documents
-
—
—
Has anyone posted a CAD model of the recommended ball screws anywhere?
Has anyone posted a CAD model of the recommended ball screws anywhere?
-
—
—
Hello everybody, I review the HercuLien machine and it has all that I have ever wanted
Hello everybody,
-
—
—
Parts for my printer are trickling in at about the same pace I order them...
Parts for my printer are trickling in at about the same pace I order them… It’s like having Christmas every week!
-
—
—
Any tips/tricks/settings for PETG? I keep getting blobbing and little zits
Any tips/tricks/settings for PETG? I keep getting blobbing and little zits. I know I need to fiddle with the retract and maybe wipe coast. Does anyone have suggestions?
-
—
—
Having a little struggle with my extruder that refuses to extruded consistently
Having a little struggle with my extruder that refuses to extruded consistently. Used for a long time a traditional geared hobbed bolt, but this one is extruding unreliable. Used for a while a gunstruder (belt driven) http://www.thingiverse.com/thing:1247952, which extrudes far more constant but the inner belt is running of the idlers after a while. So my question is what are you using as extruder and would you recommend it?
-
—
—
So I'm gearing up to build the Herculien that I've been putting off for a while (even though I have most if not all of the mechanical build components)
So I’m gearing up to build the Herculien that I’ve been putting off for a while (even though I have most if not all of the mechanical build components). I did have a question for the community, what controller are you all using and what should I go with?
-
—
—
So in the pursuit of perfection, I thought I'd post this in the interest of finding potential causes
So in the pursuit of perfection, I thought I’d post this in the interest of finding potential causes.
-
—
—
My printer is still a big battlefield (need to print a few thinks to complete it), but it started to print today
My printer is still a big battlefield (need to print a few thinks to complete it), but it started to print today. It is now printing it’s first print :)
-
—
—
Im so happy Its working :) Thanks to continuosly support from Martin Bondeus its now working .
Im so happy
-
—
—
Does anyone have different size spool holders that work with the mount in the Eustathios V2?
Does anyone have different size spool holders that work with the mount in the Eustathios V2? I have a new spool of PETG from MG chemicals that has a small opening and the default spool stl included is too larger.
-
—
—
Arthur Wolf Eric Lien Another smoothieware config question on my Azteeg X5 V3
+Arthur Wolf +Eric Lien
-
—
—
I've got some self aligning bronze bushings on order (am I cheap for thinking $42 for 8 is kinda pricey?) for some replacement Eric Lien design carriages...unfortunately, I can currently only print in PLA...while abs would be
I’ve got some self aligning bronze bushings on order (am I cheap for thinking $42 for 8 is kinda pricey?) for some replacement +Eric Lien design carriages…unfortunately, I can currently only print in PLA…while abs would be the ideal material, the printer I have available doesn’t have a heated print bed.
-
—
—
My printer just died in the middle of a print
My printer just died in the middle of a print. But I found the problem ;-)
-
—
—
I hope it's ok I keep posting this stuff
I hope it’s ok I keep posting this stuff. I’ve not found a conclusive answer to my problems w/ the Eustathios V2.
-
—
—
Still trying to dig down and figure out where my issue is on my prints
Still trying to dig down and figure out where my issue is on my prints. I’ve now got a 120mm fan cooling the steppers(can put my fingers on the heat sinks indefinitely w/out any issue)
-
—
—
Suddenly I'm losing steps on my printer
Suddenly I’m losing steps on my printer. It seems to always go one direction on the list steps. When I abort the print it sits and makes an odd ticking/thumping noise in the motors.
-
—
—
Anyone ever had a file which wouldn't 'play'?
Anyone ever had a file which wouldn’t ‘play’? I’ve had it happen a couple times where it just doesn’t do anything. Doesn’t start the heat up or timer etc?
-
—
—
A third Benchy print and the results I've tuned the extrusion multipliers etc (as noted by Eric Lien and I've upped my print temps on this one to 225(PLA)
A third Benchy print and the results
-
—
—
I have Walter's mini space invader carriage with two 24V blower fans and I just realized the pins on the Azteeg X5 mine v3 only has two fan outputs
I have Walter’s mini space invader carriage with two 24V blower fans and I just realized the pins on the Azteeg X5 mine v3 only has two fan outputs.
-
—
—
Second Benchy print. Increased the retraction to 1.5mm but didn't have much effect
Second Benchy print. Increased the retraction to 1.5mm but didn’t have much effect. I’ll try a much higher retract next.
-
—
—
A few more pics of first prints on my Spider V2
A few more pics of first prints on my Spider V2.
-
—
—
How tight are the bushings meant to be?
How tight are the bushings meant to be? I used to alignment tools to align and carriage with the printer upside-down. My carriage is still almost impossible to move with my pinky finger. Is there something I’m missing here? Some of the bushings had the brass parts loose when I put the rods in. (I have no steppers on)
-
—
—
Eric Lien mentioned he likes videos of first prints so I thought I'd post a couple of mine
+Eric Lien mentioned he likes videos of first prints so I thought I’d post a couple of mine. Wiring is a rats nest currently but figured I’d do some runs on it in case I have to make changes (and I have had to make a couple).
-
—
—
The long weekend is ending and I'll have to return to work, but I've made some decent progress on my first build
The long weekend is ending and I’ll have to return to work, but I’ve made some decent progress on my first build. All the belts are in place for the movement systems and seem to work reasonably well; my next step is to find a place locally that can cut a plate for the bed, then I can see about wiring this thing up properly. I’m very pleased with the design so far - I’m excited to get this thing working.
-
—
—
I just wanted to say thanks. I've learned a lot from building the Eustathios printer and you all helped, with comments and pictures and ideas
I just wanted to say thanks. I’ve learned a lot from building the Eustathios printer and you all helped, with comments and pictures and ideas. I’ve taken what I’ve learned and moved in a slight different direction and built a small vacuum former. I know this is way off topic, and I can easily guess what the comments will contain ;) I’ve got information on the build on github (https://github.com/RickSollie/Fornax-Vacuum-Former) if you are interested.
-
—
—
Hi Im building a herculien. I'm about to start soon but I'm struggling with the configuration of the G LCD at the smoothie board .
Hi
-
—
—
Anyone ever used the Flex3Drive system. They have a kit which specifically is noted for the Eustathios and HercuLien?
Anyone ever used the Flex3Drive system. They have a kit which specifically is noted for the Eustathios and HercuLien?
-
—
—
Eric Lien I am curious about the history of the carriage support rods spacing and setting them to 14mm instead of the Ultimakers 18mm
+Eric Lien I am curious about the history of the carriage support rods spacing and setting them to 14mm instead of the Ultimakers 18mm.
-
—
—
Hello! I just wired up my Azteeg X3 V2 with the latest marlin firmware, and I cannot get the steppers to behave correctly
Hello! I just wired up my Azteeg X3 V2 with the latest marlin firmware, and I cannot get the steppers to behave correctly. They are set to 1.5A (2X vref - .75 V) They only move a step backward and move forwards loudly and with little torque. They have great holding torque, though. See attached vids
-
—
—
So the laptop that I was using for 3D printing, the solid state drive failed
So the laptop that I was using for 3D printing, the solid state drive failed. I didn’t have any of my repetier host settings backed up. ugh…
-
—
—
Celebrating my first design /print effort, but have a question too
Celebrating my first design /print effort, but have a question too. I designed this meter mount with openSCAD, ran it through slic3r, and printed on my HercuLien in one session. Happy with the smoothieboard too, and the new web interface.
-
—
—
Hi everyone ... I want to make an offer about wiring this 3D printer
Hi everyone … I want to make an offer about wiring this 3D printer. I have finished everything frame parts and have every component ready to go. But just don’t have time to wire it and test. So if anyone can help me to wire and finish it, I can pay 50 per hour for wiring and location is in downtown Los Angeles, CA. Thank you.
-
—
—
Hey guys, Today the heated bed on my Eusthatios was quite cold even though it showed 100C (the temp I set it to)
Hey guys,
-
—
—
Hi all, I'm trying to sell all the parts necessary to build a Eustathios V2
Hi all, I’m trying to sell all the parts necessary to build a Eustathios V2. Notable parts in the mix, include a smoothieboard, a viki2 lcd, a bondtech extruder. I’m not wanting to part it out, I’d rather sell it as a whole “kit”.
-
—
—
Interesting new product (even though I can barely print with one yet!):
Interesting new product (even though I can barely print with one yet!):
-
—
—
I think I've blown a stepper driver..
I think I’ve blown a stepper driver.. Last night I got every axis moving except the X. I couldn’t even get a ‘bump’ or hum. After checking wiring and everything else I pulled the stepper driver and found this.
-
—
—
Stupid question: what's the best way to cut 10mm rods?
Stupid question: what’s the best way to cut 10mm rods? Since I’m using Walter’s Mini space invaders carriage I want to move to 10mm rods and have a couple that are a little bit too long. I’ve read somewhere that they are difficult to cut, but haven’t tried myself yet.
-
—
—
Eric Lien what do you use as your thermistor for the AliRubber heated bed?
+Eric Lien what do you use as your thermistor for the AliRubber heated bed?
-
—
—
Does the Azteeg X5 V3 require both 24vdc as well as 5vdc via the usb ?
Does the Azteeg X5 V3 require both 24vdc as well as 5vdc via the usb ? Or does it just need the 12-24vdc?
-
—
—
Limit switch wiring Does the Azteeg X5 V3 require NC or NO limit switch wiring?
Limit switch wiring
-
—
—
I wonder if anyone can help. I have upgraded my Eustathios hybrid to use the Herculien mod e3d v6 + volcano dual extruders, however I have 2 different motors running them
I wonder if anyone can help. I have upgraded my Eustathios hybrid to use the Herculien mod e3d v6 + volcano dual extruders, however I have 2 different motors running them. 1 geared nema 17, and 1 non geared nema 17 with bondtech drive gears.
-
—
—
I have been slowly building my Eustathios from Eric Lien s design for awhile now, I just recieved my 1204 ball screws and last parts I need are my alum bed plate and bed heater now
I have been slowly building my Eustathios from +Eric Lien s design for awhile now, I just recieved my 1204 ball screws and last parts I need are my alum bed plate and bed heater now.
-
—
—
Eric Lien Stephen Baird Tomek Brzeziski Nathan Walkner Special shout out as a group who responded to my help request, compare two days ago, to tonight's efforts, thanks to you all taking time to respond!
+Eric Lien +Stephen Baird +Tomek Brzeziński +Nathan Walkner
-
—
—
Next Steps for me are to learn more about the 3D printing and a few questions come to mind as I look to tune the printer and set up the slic3r program (also looking for suggested alternative programs);
Next Steps for me are to learn more about the 3D printing and a few questions come to mind as I look to tune the printer and set up the slic3r program (also looking for suggested alternative programs);
-
—
—
Eric Lien & Group... I am planning on building this printer for the company I work for
+Eric Lien & Group…
-
—
—
I have created a Open-Source software that helps configuring a Marlin based 3D printer
I have created a Open-Source software that helps configuring a Marlin based 3D printer.
-
—
—
Heated bed wiring. On the silicone heated bed, should the wires come out the rear of the bed or one of the sides?
Heated bed wiring.
-
—
—
I have produced my first test piece, the 40 mm square cube, I I have missed something
I have produced my first test piece, the 40 mm square cube, I I have missed something. The X and Y setup are pretty good they came out at 39.69; but the z axis is wrong, coming in at 20 mm which is half the height, I know I have missed a setting for this, but do I double my steps for z, or divide in half? #notgoodwith math
-
—
—
Anyone know how to remove pins from the molex connectors in the BOM?
Anyone know how to remove pins from the molex connectors in the BOM? It is a Microfit 3.0 8 pin connector. One of my wires snapped after installing, followed by a second when trying to remove the first…
-
—
—
Hey guys! Would anyone here be able to assist in making a mount for my BLTouch to mount onto my Herculien Carriage?
Hey guys!
-
—
—
Hi makers I'm rewiring my 3D printer
Hi makers
-
—
—
Morning guys and gals. I have started developing issues with my Z axis, essentially I think they are miss-alligned
Morning guys and gals.
-
—
—
Azteeg X5 V3 connections- I've got a couple questions in hooking it all up
Azteeg X5 V3 connections-
-
—
—
Two heatbed heatzones in synch ? So Im building a sort of Herculien (z-axis) / Core XY printer (with linear Rails on the x axis ), basically for the need of a 20 x 80 cm printbed
Two heatbed heatzones in synch ?
-
—
—
Morning people, coffee kicking in. I have something to share with the group if i may which could be of interest to some of you
Morning people, coffee kicking in.
-
—
—
Hello, a few of my bushings are very very stiff
Hello, a few of my bushings are very very stiff. One even scratches the rod as it moves. I am using the Misumi rods and a few work really well, but that cross rod is slightly tilted, haven’t tried with the carriage yet…
-
—
—
Eric Lien Do you have a config file (Marlin for an X3) for the Eustathios?
+Eric Lien Do you have a config file (Marlin for an X3) for the Eustathios? I can only find the smoothie one on the github
-
—
—
Aluminium profiles for building and construction, industry.......etc
Aluminium profiles for building and construction, industry…….etc
-
—
—
Fitting bushings It seems my bushings for the 10mm rods are a 'size on' fit
Fitting bushings
-
—
—
E3D V6 temp sensor. Thinking I'll upgrade my hot end to the new screw retained temp cartridge
E3D V6 temp sensor. Thinking I’ll upgrade my hot end to the new screw retained temp cartridge. Is anyone using the PT100 system provided by E3D? I’m using the new Azteeg x5 V3 smoothie board
-
—
—
Running the X-Y break in code... this is early in the process, but I have run it about 2.5 times and I still have the vibration that can be seen/heard in the video
Running the X-Y break in code… this is early in the process, but I have run it about 2.5 times and I still have the vibration that can be seen/heard in the video. The vibration is most pronounced when moving diagonally or towards the end of the movement. The carriage is easier to move than it was prior to running the gcode but still isn’t quite right. I have tried doing as was suggested by Walter and moving the carriage into each corner and loosening the lower bearing block a little but it hasn’t helped. It appears that the bearing block may be limited in the allowable adjustment. The upper bearing block is butted up against the upper extrusion and the lower one appears to be butted against the lower extrusion in all corners. Would it make sense to pop off the lower bearing blocks and shave a little off one side to allow more “wiggle room” against the lower rail?
-
—
—
Well this isn't a good start for my Tuesday 3D printing...
Well this isn’t a good start for my Tuesday 3D printing… I started this print on Friday and it sat on the printer until today. I’m not sure if the printed red handle caused this boro glass to break or what happened. My pieces have been sticking awesome lately so I don’t know if it stressed the glass enough to break it.
-
—
—
This looks interesting
This looks interesting
-
—
—
Regarding the config for Smoothieboard, should we use the one on the github for spider V2 or directly from Smoothie?
Regarding the config for Smoothieboard, should we use the one on the github for spider V2 or directly from Smoothie? The reason I ask is because the V2 config is a year old, and I am using the X5 Mini V2 Azteeg board. Are there significant differences in the config?
-
—
—
E3D hotend socks are out! Already ordered 9!
-
—
—
Slowly making progress, finally finished all the mains wiring with SSR
Slowly making progress, finally finished all the mains wiring with SSR. Not a huge fan of Dupont connectors either. I had a bent 10 mm rods from Aliexpress, contacted the seller and the replacement was also bent. Paid a bit in shipping for a Misumi one, but the quality is definitely better.
-
—
—
Hey guys, I've been fighting ball screws
Hey guys, I’ve been fighting ball screws. Most request I get for them come from this group. Through Eric Lien I learned that I cannot chuck on these in a lathe with a 3 or 4 jaw, so I ordered 5C collets. After researching I found I had to anneal them, then manually grind off the threads to remove the interrupted cut. One gentleman has been pretty patient with me, and after holding for a while I got the right feeds and speeds and made a set for him. The cuts were accurate and beautiful.
-
—
—
Finally got around installing Walter Hsiao 's mini space invaders carriage, while redoing a few other bits and pieces
Finally got around installing +Walter Hsiao’s mini space invaders carriage, while redoing a few other bits and pieces. Such a great upgrade!
-
—
—
Paging Walter Hsiao ...what infill did you use on these amazing parts?
Paging +Walter Hsiao…what infill did you use on these amazing parts?
-
—
—
Does anyone here know of a good glass supplier in the UK (or preferably Wales)?
Does anyone here know of a good glass supplier in the UK (or preferably Wales)?
-
—
—
I've officially given up trying to resolve the conflicts with mine and Eric Lien 's branch of the Herculien on github...
I’ve officially given up trying to resolve the conflicts with mine and +Eric Lien’s branch of the Herculien on github… Instead, I’m hosting my mods in a separate repository that can be found here: https://github.com/drtrain/Herculien-Mods
-
—
—
Here's where I am on my build
Here’s where I am on my build. I’m using an X3 with dual saintflint’s powering a Chimera. Any advice/tips you guys have? This is my first printer build, but I’ve had 4 years experience with MakerGear m2’s, prusia i3’s and the hell on earth that makes up MakerBot (well the newer models at least) :P Do I put the whole carriage (with cross rods and all) onto the guide/drive rods as one piece? or just put the bushing holders on and slide the cross rods on the those?
-
—
—
Got this current meter in the trash from a company (still in the unopened packaging) Planning to put on the 24V line to the X3, should look pretty cool!
Got this current meter in the trash from a company (still in the unopened packaging) Planning to put on the 24V line to the X3, should look pretty cool!
-
—
—
Hi guys, I am in the process of building the Eustathios v2
Hi guys,
-
—
—
which version of marlin you use ? Ramps 1.4
which version of marlin you use ?
-
—
—
Has anyone else issues with opening the Zane Baird mod files for the Herculien?
Has anyone else issues with opening the +Zane Baird mod files for the Herculien? I can open the stl files for the tensioner blocks, and the photos, but the rest of the stl files produce error in Netfabb (invalid stl file) and I also get error on the Solidworks files
-
—
—
Anyone else has any problem ordering from SDP-SI?
Anyone else has any problem ordering from SDP-SI? I placed an order last month and I haven’t received any order confirmation or a shipping date. I also haven’t been billed…
-
—
—
My printer's having a hard time doing small details with low-extrusion areas (fine details at low layer heights)
My printer’s having a hard time doing small details with low-extrusion areas (fine details at low layer heights). I think it’s something to do with the bowden setup and such. I’ve been looking at doing a new carriage, and I like +Walter Hsiao’s mini space invader one, so I think i’m going to switch to that, but because of this extrusion issue, I think it might be worth going whole-hog and doing the flying extruder. Does anyone know where i can find the files to do this? I can’t seem to find them anywhere.
-
—
—
I've had interest in 3d printers and have been wanting to build one for my next project
I’ve had interest in 3d printers and have been wanting to build one for my next project. Funny how a mention and a split second picture on one of Thomas Sanladerer’s youtube videos hooked my interest in the HercuLien so much. I am very much still in the planning phase and intend to take my time as the build is sometimes the most enjoyable part to me.
-
—
—
Help! I accidentally unscrewed my ball screw and I have no Idea how to put it back together!
Help! I accidentally unscrewed my ball screw and I have no Idea how to put it back together!
-
—
—
I mentioned the Kitten Printer here a bit ago
I mentioned the Kitten Printer here a bit ago. Just got this kit in. Small form factor and well designed. The parts in the kit were printed on another Kitten.
-
—
—
Hi everyone, I would like to put a solid state relays on my eustathios because my bed heats no more than 65 degrees , what relay to choose ?
Hi everyone,
-
—
—
I am happy today, got the entire afternoon off to stay home and I am close, so very close to getting my printer going, but I have a few things to adjust
I am happy today, got the entire afternoon off to stay home and I am close, so very close to getting my printer going, but I have a few things to adjust.
-
—
—
Feels pretty good, now just need to mount it
Feels pretty good, now just need to mount it. I wish I made the mounting tabs thicker. We’ll see if it holds up.
-
—
—
Would anyone like to provide thoughts or alterations that should be made to the model?
Would anyone like to provide thoughts or alterations that should be made to the model? Building on Eric’s stacked azteeg x5 mini/Raspberry pi combo, I included holes for a 5mm button head to mount directly to the extrusion. The images are missing the additional peg support but you get the idea. Also, these images are upside down.
-
—
—
Would anyone be able to provide the mounting hole dimensions for the Azteeg X5 Mini V3?
Would anyone be able to provide the mounting hole dimensions for the Azteeg X5 Mini V3? I would like to build upon Eric’s recently redesigned mount and allow it to be mounted directly to the 2020 rail rather than the bottom surface of the printer. The Raspberry pi would also be built in, to make a stacked mount.
-
—
—
I think I just witnessed the single most rare print failure
I think I just witnessed the single most rare print failure. Partway through the print, the Y shifted just enough so that the female threads printed over the male threads. It was spaghetti for about one CM then printed perfectly and the threads worked! To top it all off, the printer had a foot of filament left!
-
—
—
Hello! Just wondering what to do for extruders
Hello! Just wondering what to do for extruders. I’m using a Chimera. I will want to upgrade to a bondtech in the future, but $310 is too much for me to spend on two extruders. I’ll be playing with all different types of filament and I want something cheep that won’t jam. Should I just go with the hercustruder? I kinda forgot to order the parts for it though, so shipping may be a bit much. I also want to use the same motor (and preferably drive gear) of the bondtech so I can upgrade just one extruder at a time. Thanks! - Stefano
-
—
—
Hi all, is anyone living in CA with Eustathios 2 printer?
Hi all, is anyone living in CA with Eustathios 2 printer? I have a small favor want to ask @@” Thanks
-
—
—
Hi Everyone, I just wonder what software you used for slicing with Eustathios or HercuLien ?
Hi Everyone, I just wonder what software you used for slicing with Eustathios or HercuLien ? Thank you
-
—
—
Is this a problem? It takes a ton of force to make the holder flat
Is this a problem? It takes a ton of force to make the holder flat. Printed on a MakerGear M2 with PLA, 3 shells, 80 percent infill.
-
—
—
This is a question to all those running a SSR with a 500W silicone bed
This is a question to all those running a SSR with a 500W silicone bed. Do you find that the SSR heats up enough to warrant a heatsink?
-
—
—
Just wanted to share my build since it has been a little quiet
Just wanted to share my build since it has been a little quiet. Granted what you see has been completely disassembled… After the frame was on, I put the z axis and bed, then the x and y axis only to discover that I had goofed on drilling the holes. Somehow halfway through I confused the vertical extrusions and put the 80mm hole on top instead of the bottom, resulting in not enough clearance for the x and y bars. I am pretty sure I even saw a post recently about this…
-
—
—
Eric Lein is there any company selling HercuLien Kits?
+Eric Lein is there any company selling HercuLien Kits? I would like to build one but if I have to have a 3D printer to make a my first 3D printer it is difficult to begin.
-
—
—
Are folks still building Eustathios printers? I printed a mostly-complete set of parts to torture-test my printer and would like to get them to someone who is going to build since I have less cycles at the moment
Are folks still building Eustathios printers? I printed a mostly-complete set of parts to torture-test my printer and would like to get them to someone who is going to build since I have less cycles at the moment.
-
—
—
Any idea why the printer is pausing?
Any idea why the printer is pausing? 4 hours into a print and I see a couple bubbles and noticed that the printer is pausing.
-
—
—
Hey, where can I find the 6900 series bearings?
Hey, where can I find the 6900 series bearings? I can’t find them on Robotdigg. (Listed on BOM as 5972K164)
-
—
—
Should I go with 2 E3D V6's or one chimera?
Should I go with 2 E3D V6’s or one chimera? I plan to order both at the same time. I have seen some members with 2 V6’s so I was wondering if there is an advantage of that setup. (I’m going with 2 Volcanos anyway.) Thanks!
-
—
—
Is there a PDF of the through holes for the 562 mm extrusions?
Is there a PDF of the through holes for the 562 mm extrusions? I know there is 1 hole at 80 mm, another at 470 mm; however I don’t see where the top hole is located. As I understand it from reading other posts, it’s shifted to allow room for the extrusion end caps. So those holes would be 10 - end cap thickness?
-
—
—
About the lcd module (12v * 2) wiring for 24 v power supply in this photo
About the lcd module (12v * 2) wiring for 24 v power supply in this photo. Is it correct? Thanks
-
—
—
Why does this keep happening? Mid print, it just stops printing and I can't push any filament in through the hotend
Why does this keep happening? Mid print, it just stops printing and I can’t push any filament in through the hotend. The hotend shows that it’s 230 some degrees for Hatchbox PLA.
-
—
—
Hey guys So since I know this community is Most likely to use azteeg x5 mini does anyone have any idea how to get a reprap discount controllers sdcard slot to work on it
Hey guys
-
—
—
Hey there, I will soon (probably in a few months to get everything in and assembled) be joining your ranks
Hey there,
-
—
—
Hey All, The packages have been arriving fast and furious
Hey All,
-
—
—
Thanks for the add to the group
Thanks for the add to the group. I’ve been thinking of converting my eclip3d coreXY printer into either of the HercuLien or Eustathios. Having seen some amazing prints from Eric Lien. I was wondering, why does this type of printer seem to produce better prints in general to a coreXY machine. What are the advantages or disadvantages. Sorry if this has been asked before, just trying to expand my knowledge further.
-
—
—
Hello, I printed this 6 way PVC connector
Hello,
-
—
—
I've been using a PEI sheet for a few weeks now and am really happy with the result
I’ve been using a PEI sheet for a few weeks now and am really happy with the result. Prints seem to stick better the longer I use it, to the point that I’m struggling sometimes to remove objects.
-
—
—
Hi, I have a question about fans with extruder, the main fan 30*30 and 4020 blower should be wired with different ports, right?
Hi, I have a question about fans with extruder, the main fan 30*30 and 4020 blower should be wired with different ports, right? which port I should wire for 4020 blower. Because I want to set which layer it will start to blow the print. Thanks
-
—
—
Hi guys, So I'm planning on constructing a 3D printer ok?
Hi guys,
-
—
—
Sure wish connectors didn't confuse me so much
Sure wish connectors didn’t confuse me so much. Finding an ideal, power rated, elegant, cheap solution isn’t easy…Check out this Molex part…looks like it’d handle a dual extruder easily. Now, price all the pins, coax connectors, figure out the cable side with stress relief..oh, and they STRONGLY suggest crimp connectors…drop some coin on a good crimper.
-
—
—
I have a stupid question about SSR.....very stupid and working on it now...
I have a stupid question about SSR…..very stupid and working on it now… thanks everyone’s help
-
—
—
Fix lcd location
Fix lcd location
-
—
—
I made a model for the Azteeg X5 Mini V3 (with a great starting model provided by Roy Cortes )
I made a model for the Azteeg X5 Mini V3 (with a great starting model provided by +Roy Cortes). I did it so I could update the mount for the Eustathios Spider V2. I made a new electronics mount in two configurations (side by side and over under) along with the raspberry Pi for octoprint.
-
—
—
It's been a long time coming, but I have some updates for those using the Herculien
It’s been a long time coming, but I have some updates for those using the Herculien.
-
—
—
How much will it cost me to build a V2 Eustathios?
How much will it cost me to build a V2 Eustathios?
-
—
—
I'm having trouble finding a supplier w/ the 10mm x500mm(L) rods for reasonable price
I’m having trouble finding a supplier w/ the 10mm x500mm(L) rods for reasonable price. Looked at metric drill rod but not sure if that’s good enough? Anyone have a good/reputable option from AliExpress? Could order from Misumi but the price is pretty eye watering..
-
—
—
nylon hex lock nut .... This is really hard to screw in it ....
nylon hex lock nut …. This is really hard to screw in it …. does anyone have easy way to do it right ? Thanks
-
—
—
Just recieved a nice PEI coated 8mm plate;)
Just recieved a nice PEI coated 8mm plate;)
-
—
—
Glass surface, should it be tempered or just plain plate glass (if I forgo getting borosilicate glass)??
Glass surface, should it be tempered or just plain plate glass (if I forgo getting borosilicate glass)??
-
—
—
Recommendations on how thick to get the acrylic panels?
Recommendations on how thick to get the acrylic panels? I’m assuming 1/8 is enough or?
-
—
—
it seems I can't use 3mmX12mm_Buttonhead(McMaster_92095A183) to screw in Endstop Subminiature Switch ....
it seems I can’t use 3mmX12mm_Buttonhead(McMaster_92095A183) to screw in Endstop Subminiature Switch …. Is anyone also has this problem ? or I need to re-drill a hole ? Thanks
-
—
—
Has anyone here built a Kitten Printer?
Has anyone here built a Kitten Printer? I am very interested in hearing about it if so.
-
—
—
Printed this small blower a few days ago, this eustathios is awesome !
Printed this small blower a few days ago, this eustathios is awesome ! The grey filament is new, still need to tune some stuff. The fan is almost perfect.
-
—
—
Lighting options. I've seen several people write about various LED lighting they've installed into their printers in printed tracks etc
Lighting options. I’ve seen several people write about various LED lighting they’ve installed into their printers in printed tracks etc. just wondering if anyone here has recommendations on where to source LED’s and how they connected them up etc? Is it as easy as bare LED’s to which you solder wiring in parallel or can you buy small circuit boards to solder the LED’s and the wiring or? Suggestions appreciated!
-
—
—
....one hour only get this done ... -_-
-
—
—
Ballscrews for Eustathios. Eric Lien the guys at smw3d were saying you have a new design/drawing for the ballscrews?
Ballscrews for Eustathios. +Eric Lien the guys at smw3d were saying you have a new design/drawing for the ballscrews? Just thought I’d ask before ordering them.
-
—
—
This seems to be a thorn in my side
This seems to be a thorn in my side. This happens to me every time I apply the 3D-EEZ film. This time it’s really bad. I’m posting it on here hoping more people will see it and have recommendations.
-
—
—
Raspberry Pi2- I see that the Pi3 is out, worth buying the newer version or sticking to the '2'?
Raspberry Pi2- I see that the Pi3 is out, worth buying the newer version or sticking to the ‘2’? I’ve no clue about them, just sitting down to watch +Thomas Sanladerer how-to video
-
—
—
E3D V6- is it worth buying the PT100 temp sensor vs the standard 100K?
E3D V6- is it worth buying the PT100 temp sensor vs the standard 100K? If I’m using a Azteeg X5-Mini V3, I assume I’d also have to buy the PT100 Amplifier board as well?
-
—
—
Is there any reason I can't make 36 tooth x8mm id pulleys on the Z screws?
Is there any reason I can’t make 36 tooth x8mm id pulleys on the Z screws? (BOM calls for 30 tooth) I’m going to use 1204 ballscrews instead of leadscrews.
-
—
—
Digikey-Molex connectors. On the BOM it notes one of each part
Digikey-Molex connectors.
-
—
—
Designed a case for the 12864 display
Designed a case for the 12864 display
-
—
—
This is impressive
This is impressive.
-
—
—
Trying to figure out how to drill the hole for the Eustathios but just laying it out it seems rather different to this image
Trying to figure out how to drill the hole for the Eustathios but just laying it out it seems rather different to this image. If I use 80mm based on the BOM for spider v2 the gap highlighted green is almost non-existent. Is there a drill guide for the extrusion bolting for Eustathios or a list of drill measurements? Is the 80mm centre to centre of the cross extrusion (from top one to support one)?
-
—
—
E3D Titan vs Bondtech Has anyone used both?
E3D Titan vs Bondtech
-
—
—
Hmm how much abuse you think the silicon heat pads can take?
Hmm how much abuse you think the silicon heat pads can take? i just peeled mine off the aluminum. never folded the silicone off its self. was worked slowly at most of a 90 degree.
-
—
—
Stepper selection time. Comparing the 2.0A Nema 17 at SMW3D Pn-1705HS200A ( ) which has more torque vs the 1.5A motors at Robotdigg (as listed on the BOM)
Stepper selection time. Comparing the 2.0A Nema 17 at SMW3D Pn-1705HS200A ( http://smw3d.com/nema-stepper-motors/) which has more torque vs the 1.5A motors at Robotdigg (as listed on the BOM).
-
—
—
Has anyone ever changed the Z stage 'H' frame to have a second crossbar the same dimensions as the center bar but placed at one end of the 'H'
Has anyone ever changed the Z stage ‘H’ frame to have a second crossbar the same dimensions as the center bar but placed at one end of the ‘H’. Then you could use 3 point leveling instead of 4. I’d put it to the back so two screws are at the front.
-
—
—
Looking forward to building a Eustathios Sprider V2
Looking forward to building a Eustathios Sprider V2.
-
—
—
About 320x320_120V_500W_Heated_Bed on BOM sheet. Is it 500W right?
About 320x320_120V_500W_Heated_Bed on BOM sheet. Is it 500W right? the Power supply Meanwell_SP-200-24 can handle it ? @@”
-
—
—
Questions about assembly on bearings and pulleys
Questions about assembly on bearings and pulleys. The ball bearings and the holders, how do people hold the bearing in place? Do you glue it or just have the pulley hold it in place.
-
—
—
Sleeve for electrical wiring designed and printed a custom sleve to join electrical tubes with different diameters
Sleeve for electrical wiring
-
—
—
So I am playing with a fun new (unreleased) controller and some drivers from Roy Cortes at Panucatt
So I am playing with a fun new (unreleased) controller and some drivers from +Roy Cortes at Panucatt. Dual extruder capable smoothieware based unit. I have been waiting to try this thing for a while. Just my luck. I get everything installed and now I have to travel for work next week. Guess I need to get some energy drinks and do my initial testing and tuning before I go.
-
—
—
I dont understand. On the github for spider v2 it says "Build Volume: 285x285x295mm" but the bed it uses is much larger?
I dont understand. On the github for spider v2 it says “Build Volume: 285x285x295mm” but the bed it uses is much larger?
-
—
—
I hope it's all I need to print ... Haha
I hope it’s all I need to print … Haha
-
—
—
Hello All I haven't been here in a while
Hello All
-
—
—
Hello , everyone. I'm wondering if anyone use BLTouch as auto level tool with Eustathios?
Hello , everyone. I’m wondering if anyone use BLTouch as auto level tool with Eustathios? And also what changes I need to do if I want to use BLTouch ? I’m thinking about using Cartesian Flying Extruder with BLTouch. Is it possible ? or I don’t need auto level system with Eustathios ? Sorry for so many questions…
-
—
—
I was thinking of building of printing the Herculien or Eusthios but to use conduit instead for the frame, similiar to what this guy did with the Hbot design
I was thinking of building of printing the Herculien or Eusthios but to use conduit instead for the frame, similiar to what this guy did with the Hbot design. Any idea or suggestions welcome?
-
—
—
I need help about the 5052 Aluminum Sheet for Eustathios hot bed, I was looking around Los Angeles CA area
I need help about the 5052 Aluminum Sheet for Eustathios hot bed, I was looking around Los Angeles CA area. And they didn’t accept for just cutting one sheet for me. Or the price is too high and I can’t accept. So if anyone can cut one and ship to CA for me, I’ll really appreciate it.(if the price is affordable for me.) Thank you … And I think I will buy AZSMZ Mini Ver2.1 + AZSMZ 12864 LCD + 4 x DRV8825 instead of Azteeg X5 for my board.
-
—
—
I made a low profile spool holder with parts who where laying around
I made a low profile spool holder with parts who where laying around.
-
—
—
So for the last two years I've been working on my ingentis/eutathios build
So for the last two years I’ve been working on my ingentis/eutathios build. I’m a down to hotend and extruder and electronics. I plan to use e3d v6 and was curious of the ptfe length that everyone is using.
-
—
—
I own the Pegasus 12" printer and I would like to one from this group
I own the Pegasus 12” printer and I would like to one from this group. I would like to keep as many parts as possible. I also want to make it a heated chamber. Can anyone suggest a proper build for me http://www.makerfarm.com/index.php/12-pegasus-kit.html
-
—
—
Here are the first 2 print attempts on eustathios!
Here are the first 2 print attempts on eustathios! Still need to calibrate s3d retract/coast settings but the second seems to be pretty close to correct ones. In first print it was under extruding when it had to print solid bottom layers maybe because the nozzle temp was to low. On second one I raised the temp to 240 for first 3 layers and the to 235 for the rest of the print. First time I am using bowden extruder so still I don’t have the needed know how! Need to be done yet some cable management and to mount the board beneath the printer.
-
—
—
Currently doing some remodeling on my OpenBeam printer
Currently doing some remodeling on my OpenBeam printer. It’s been sitting in storage for a whole year. About two month back I suddenly got the urge again to try and complete the printer. Replaced most of the printed parts except those on the Z-axes. I’ve also installed a Titan extruder. At the moment, I’m trying to sort out power, controller and cabling. Going slowly with a torn ligament though. Would have liked everything in a single color but using what is available at the moment.
-
—
—
Has anyone fooled around with trying to put a Titan extruder on the Eustathios?
Has anyone fooled around with trying to put a Titan extruder on the Eustathios? I have one but I am still trying to picture a head design for direct drive. If anyone has used the Titan, how was the performance? I already have one, it’s been in it’s box together with a 20 mm NEMA17 for over a month with little time to play with it.
-
—
—
Extruder distance/bowden lenght when mountig extruder above bed I'm trying to figure out the right hight for the upper lid of my enstathios before building an enclosure around it
Extruder distance/bowden lenght when mountig extruder above bed
-
—
—
Hi everybody! Eustathios build continues, but I need a little guidance
Hi everybody! Eustathios build continues, but I need a little guidance.
-
—
—
Making printers is easy, keeping them living is hard
Making printers is easy, keeping them living is hard. Making a dynamic system with fine tolerances, and necessary maintenance is not an easy thing to do.
-
—
—
Couldn't resist to wait any longer and decided to make a first trial
Couldn’t resist to wait any longer and decided to make a first trial. X and Y rods are still loose and still waiting for a heatbed. As a temporarily solution just printed on a loose sheet of paper. Calibration was limited to real basics (X,Y,Z,E steps). Sounds promising for the next steps.
-
—
—
OK, thanks for all the input. Now other than print size and cost are the HercuLien and Eustathios comparable in ability?
OK, thanks for all the input. Now other than print size and cost are the HercuLien and Eustathios comparable in ability? Even +Eric Lien has commented on using his Talos3D Tria Delta a lot recently. From your experience, considering ability more important than cost, if you all were beginning again what would you build first? Then comes the chicken or the egg conundrum having printed plastic components to build a machine to print plastic components.
-
—
—
How would you compare the Taz-Mega (similar to the Lulzbot Taz sans belts) design to the HurcuLien design
How would you compare the Taz-Mega (similar to the Lulzbot Taz sans belts) design to the HurcuLien design. Other than the increased cost due to not being belt driven might it be more accurate or possibly allow for heavier heads, etc? An improved bed design would be needed.
-
—
—
I you all were going to build your first 3D printer with accuracy the most important factor, what would you build?
I you all were going to build your first 3D printer with accuracy the most important factor, what would you build? I also notice the increasing number of references to delta printers not sure if that is due to a fad or improvement.
-
—
—
Video of first prints Printed some clamps for the LED lights
Video of first prints
-
—
—
Eustathios follow up long time no posts--finally I found the time to continue my Eustathios build
Eustathios follow up
-
—
—
This is Walter Hsiao part for goldmart 1204 ball screws printed in ABS
This is +Walter Hsiao part for goldmart 1204 ball screws printed in ABS. Also a small video showing how the bushings are doing. As you can see the printer vibrates a lot so I have to lower acceleration from 9000. I am running break g code on a ramps just for testing the movement. Also there are some 2020 corners missing from the top part of the frame, maybe this contributes to vibration. Sorry for the carton paper beneath the printer but I haven’t install the rubber legs yet. Unfortunately I only have purple ABS available for now :)
-
—
—
Those are the bushings I am using for x,y and extruder carriages
Those are the bushings I am using for x,y and extruder carriages
-
—
—
The construction continues! Finally all the parts are here!
The construction continues!
-
—
—
I just wondering that is anyone want to sell their extra "Azteeg X5 mini 32BIT All-in-one Controller V2" ?
I just wondering that is anyone want to sell their extra “Azteeg X5 mini 32BIT All-in-one Controller V2” ?
-
—
—
Anyone know whats about with item 20.20 on the Spider V2 BOM (#90545A009)?
Anyone know whats about with item 20.20 on the Spider V2 BOM (#90545A009)? It has no description, and according to McMaster Carr is a Titanium Hex Nut, 8-32 Thread Size, 3/8” Width, 1/8” Height. It’s under the HercuStruder section.
-
—
—
Which kind of corner bracket is better for 2020 aluminum extrusion?
Which kind of corner bracket is better for 2020 aluminum extrusion? 17x20 piece or 20x28 piece?
-
—
—
I started a print this morning and I found this when coming back from work: halted reset or m999 Something I can do ?
I started a print this morning and I found this when coming back from work: halted reset or m999
-
—
—
So I am thinking about turning the Eustathios into direct drive rather than a bowden setup and I have an E3D Titan extruder coming
So I am thinking about turning the Eustathios into direct drive rather than a bowden setup and I have an E3D Titan extruder coming. I am hoping +Walter Hsiao is thinking about the same thing (although that is entirely wishful thinking on my part and some selfishness) and decides to either mod his current extruder carriage or create a new one. Is there anyone else who is running direct drive or is everyone running bowden?
-
—
—
So here is my obligatory 3d printed parts for the spider v2 all partss are abs from a folgertech 2020
So here is my obligatory 3d printed parts for the spider v2 all partss are abs from a folgertech 2020. I am very slowly putting it together and purchasing parts (wife… budget). I was wondering what % infill I should be shooting for, basically anything load bearing I have been doing 100%, should this also includes the carriage? I was going to go with Walter’s space invader mini. So far I have ordered the ballscrews and some bearings. I was going to purchase the extrusion from the maker shop that posted on here a few weeks ago. Does anyone know if they will start pure drilling the holes?
-
—
—
Marko se fluitjies
Marko se fluitjies
-
—
—
Michal Memeteau as requested ;) I'm way better at photography than video but it will do the job
+Michaël Memeteau as requested ;)
-
—
—
Hi again ;) I recieved the lasts parts for completing the flying extruder mod from Walter Hsiao Looks good, prints good !
Hi again ;)
-
—
—
Some of you have tried these PEI coated bed ?
Some of you have tried these PEI coated bed ?
-
—
—
Hello all. I am an upstart to this group and to 3D printing generally
Hello all. I am an upstart to this group and to 3D printing generally. I was wondering if anyone would be willing to print me a set of the printed parts for the Eustathios-Spider-V2. I would of course be willing to pay for parts. Let me know. I’m in Massachusetts if that helps at all. Thanks so much!
-
—
—
Got these today! Back to printing non-stop after I get it installed
Got these today! Back to printing non-stop after I get it installed. :)
-
—
—
I finally did something I have been meaning to do for a while
I finally did something I have been meaning to do for a while. My old HercuStruder design allowed for mounting my second extruder onto the 20x20 upright extrusion since the face of the extruder sits flush with the extrusion. But the Bondtech housing does not allow for this since the clamp holds onto the planetary section of the stepper so the Bondtech housing sits forward of the face of the extrusion. I have my control box sitting out front on a hinge, it can swing out of the way to open the front door. This would swing it back into the second Bondtech. I have had it hacked to work for a while… but I finally got around to making a new mount. The model is odd looking but places both extruders exactly how I wanted them. It was as compact as I could get things while still allowing both QR hinges to swing independently.
-
—
—
I took some pics with the thermal imager we have at work
I took some pics with the thermal imager we have at work.
-
—
—
First test with 3dBenchy before tuning, I was expecting somthing worse
First test with 3dBenchy before tuning, I was expecting somthing worse.
-
—
—
That point where you have to take your 15.5"x15.5" cast build plate and take 1/4" off both sides for clearance...and your band saw is incredibly slow and inaccurate...and the mini mill can't hold it...and it doesn't fit the
That point where you have to take your 15.5”x15.5” cast build plate and take 1/4” off both sides for clearance…and your band saw is incredibly slow and inaccurate…and the mini mill can’t hold it…and it doesn’t fit the printer.
-
—
—
Hi everybody! I am watching the site for a while now and finally I took the decision to built an eustathios!
Hi everybody!
-
—
—
Just a few parts missing! Now to just tap a ton of M5 threads and drill holes into the extrusions
Just a few parts missing! Now to just tap a ton of M5 threads and drill holes into the extrusions. Can’t wait to start building the darn thing this weekend! I’ve been lurking on this sub for a while and finally pulled the trigger. Such a great community can’t wait to be a part of it!
-
—
—
Got my correct z ballscrews and viki2 today !
Got my correct z ballscrews and viki2 today !
-
—
—
Where can I buy misumi parts in Europe?
Where can I buy misumi parts in Europe? Can I get them shipped to Iceland?
-
—
—
I'm having a lot of trouble with my printer all of a sudden
I’m having a lot of trouble with my printer all of a sudden. For some reason it stops printing part way through the print (It’s happened on a couple long-ish 3 hour prints) and I’m pretty sure it’s due to the board reconnecting (I get the stupid windows autoplay popup).
-
—
—
Hi, I would like to build a Eustathios
Hi, I would like to build a Eustathios.
-
—
—
T slot Aluminum Extrusion n V slot Aluminum Extrusion
T slot Aluminum Extrusion n V slot Aluminum Extrusion
-
—
—
Hey, I started this hobby with a Folgertech Kossel, I didn't really know where I wanted to take it, I really enjoyed the tinkering
Hey, I started this hobby with a Folgertech Kossel, I didn’t really know where I wanted to take it, I really enjoyed the tinkering. These days however as I’ve learned more I want to spend more time learning and printing CAD/CAM designs and less time making my printer work.
-
—
—
3dBenchy time. First one detached halfway through
-
—
—
Welcome to Jekyll!
You’ll find this post in your
_postsdirectory. Go ahead and edit it and re-build the site to see your changes. You can rebuild the site in many different ways, but the most common way is to runjekyll serve, which launches a web server and auto-regenerates your site when a file is updated. -
—
—
Hey, I've been using your duct Eric Lien and its been working great thanks!
Hey, I’ve been using your duct +Eric Lien and its been working great thanks! It’s been really good at overhangs, however I was having trouble keeping the extruder up to temperature. It seemed that too much air was hitting the heater block and cooling it down quite a lot. My solution was to use about 5 strips of 1cm wide kapton tape stuck to the inside of the duct across the opening, then with a knife cutting a hole for the nozzle, then attached it to the print carriage. This directs the air towards the nozzle and insulates the heater block from the direct airflow of the duct. (I’ve tried to draw this on the attached pic as best as I can to try and help explain) This has improved the ability of the extruder to get up to temperature quickly, but it was quite fiddly, and it took a long time to do. One solution could be to have the bottom of the cooling duct hinged so you could open it up, apply the kapton tape, then close it up again, I tried doing this but my 3d skill are quite poor (sorry). With this hinge in place it might be possible to also add glass fibre insulation (or some other insulation) around the heater block as well to help minimize the 3 way battle between the heater block, the cooling duct and the heat sink on the extruder.
-
—
—
Finally rearranged my office so that all four of my printers fit
Finally rearranged my office so that all four of my printers fit. Until recently I had my Eustathios in the basement and hadn’t printed with it in months until taking it out to MRRF. But I am glad I made room. I forgot how much fun this printer is.
-
—
—
I was looking at the herculien github where it is mentioned that this mechanism is superior to a corexy
I was looking at the herculien github where it is mentioned that this mechanism is superior to a corexy. Why is that so. I am intending to build a 600x600 x600 mm monster and i need to decide on the direction of mechanism to go. Any advice?
-
—
—
Well I guess I didn't screw up too bad then :) Tom is brutally honest, which I like
Well I guess I didn’t screw up too bad then :)
-
—
—
BLTouch I ve just ordered this little sensor from antclabs , might be a nice help for my herculien,
BLTouch
-
—
—
Hi, I just recieved these damn bearings :D The carriage is up and moving
Hi,
-
—
—
Random question: I think I may have stripped some grub screws in my GT2 20 tooth 8mm bore pulleys, and I don't have them in front of me to check
Random question: I think I may have stripped some grub screws in my GT2 20 tooth 8mm bore pulleys, and I don’t have them in front of me to check. Does anybody know what size grub screws they typically are so I can order some more? I’m posting here because I’m betting you guys are likely to know. :)
-
—
—
I'm trying to battle the z-ribbing that I've pretty much always had on my Eustathios, V2 and I've just had a thought that I would love someone here to explain to me
I’m trying to battle the z-ribbing that I’ve pretty much always had on my Eustathios, V2 and I’ve just had a thought that I would love someone here to explain to me.
-
—
—
I was printing the control Panel on my Eustathios 2 and realized that my X is inverted on my prints
I was printing the control Panel on my Eustathios 2 and realized that my X is inverted on my prints. This wasn’t apparent when doing simple tests and non-engineering pieces. I’m using RAMPs 1.4 board and running Marlin and have not been able to get this corrected.
-
—
—
Shauki B making a cool Z stage for his HercuLien modification
+Shauki B making a cool Z stage for his #shaulieki HercuLien modification. Looking good my friend. Reminds me of the z stage of the F306 printer: http://www.fusion3design.com/f306_large_print_volume_3d_printer/
-
—
—
Hello there, This is a little off-topic: My first printer, a BQ witbox is giving me headaches, it doesn't print round circles
Hello there,
-
—
—
Building update - I recieved the aluminium plate, plasma cutted by friend, I still need to find a glass supplier
Building update
-
—
—
I have a Herculien that I'm prepping to enclose and was wondering how you all route your wires/cables for a clean build
I have a Herculien that I’m prepping to enclose and was wondering how you all route your wires/cables for a clean build. My old printer looks like Medusa’s head. I keep seeing these super clean builds and I can’t wrap my head around it. Any pictures would help greatly, thanks!
-
—
—
How to make a nearly smooth carriage...a smooth carriage:
How to make a nearly smooth carriage…a smooth carriage:
-
—
—
Is it a big deal that I've found the secret for smooth running carriages (hint, cram the bushings home, use a $4 reamer to re-establish a 10 mm path through the carriage)
Is it a big deal that I’ve found the secret for smooth running carriages (hint, cram the bushings home, use a $4 reamer to re-establish a 10 mm path through the carriage).
-
—
—
So I discovered the awesome Eustathios design a couple months ago, bravo to the people who designed it
So I discovered the awesome Eustathios design a couple months ago, bravo to the people who designed it. It seems like the best design I have found online. My original intention was to modify it slightly to use larger aluminum extrusion for more rigidity, and reduce part count a bit (mainly by eliminating the second drive belt from the X and Y axis). However, I was having a hard time modifying the files (I use Catia for work) and ended up redrawing and modifying pretty much everything but the carriage. I intend to use one Z-axis motor ,and one ball or lead screw and one 8mm rod and linear bearing on each side of the build plate. So the two lead/ ballscrews will be one a single belt. The X and Y axis motors are in a configuration on saw here a couple weeks ago, but can’t seem to find again. It is missing a pair of idler pulleys below each X/Y motor. Of course the belts are not included either because I have no idea how to model them. I intend to use graphite impregnated bronze bushings on the X and Y slides, and the self aligning bushings per the Eustathios design in the carriage. The build volume is 300x300x300.
-
—
—
If someone with Simplify3d could help me out, I'm trying to print this model and it won't slice correctly
If someone with Simplify3d could help me out, I’m trying to print this model and it won’t slice correctly. I’d like to see if anyone else gets issues like me. The holes get filled in on the 3rd layer, and it seems to almost skip a layer around layer 22 or 23. It only happens if I set the first layer height to 100%. If it’s 95%, it seems to be okay. Any ideas? Is it just a bug in Simplify3D? It’s quite annoying.
-
—
—
For the HercuLien, do you guys wire the two fans on the hotend always on, [ just to the power supply], or do you connect them to the control board so you can turn them off and on?
For the HercuLien, do you guys wire the two fans on the hotend always on,
-
—
—
Never had this many parts without a murder suicide
Never had this many parts without a murder suicide. (Ignore the audio, couldn’t strip it from my phone.)
-
—
—
Things are getting serious, great job on designing this printer Eric Lien and same for the addons of Walter Hsiao .
Things are getting serious, great job on designing this printer +Eric Lien and same for the addons of +Walter Hsiao . It’s a pleasure to build it.
-
—
—
Measures and tolerances I'm slowly peeling out all of the IGUS bushings out of the printer, I just wasn't happy with some aspects of the printer and decided to give all of the moving parts the heave-ho
Measures and tolerances
-
—
—
McMaster and Robotdig have arrived, this heatbed is huge :P Most parts are printed, the big Z-parts are all in the printer since 27h, biggest multi parts print I ever done
McMaster and Robotdig have arrived, this heatbed is huge :P
-
—
—
I was updating the image for the G+ Group, and decided to have some fun
I was updating the image for the G+ Group, and decided to have some fun. Many people have problems visualizing the size of these machines. So I thought… why not put them in a model along side printers many people know the size of. So without further adieu here is Herculien and Eustathios Spider V2 compared to the size of an Ultimaker2 and a Prusa I3 (steel variant).
-
—
—
Working on trying to dial in carbon fiber abs
Working on trying to dial in carbon fiber abs. Going well so far but I needed to add some extra restart distance to avoid gaps after retract. Anybody have any pointers for me?
-
—
—
Hey guys, has anyone come up witha better cooling duct for the Euth V2 regular carriage?
Hey guys,
-
—
—
Well isn't this interesting... lol haaaalp It's like things aren't one solid rug roh
Well isn’t this interesting… lol haaaalp
-
—
—
Matt doing what he does so well...
Matt doing what he does so well… over building things even more than me! And making me jealous along the way.
-
—
—
Printing some big stuff for a friends company :) It's times like this that the "go big or go home" nature of the HercuLien sure comes in handy :)
Printing some big stuff for a friends company :)
-
—
—
Printed a set of Euthathios Spider V2 parts
Printed a set of Euthathios Spider V2 parts. Looking to sell it so I can get funds to build the Talos Spartan. Ping me if your interested.
-
—
—
First parts arrived today, the printer is still running
First parts arrived today, the printer is still running
-
—
—
For the herculien builders, we now have a quick (and less expensive) option for ball screws
For the herculien builders, we now have a quick (and less expensive) option for ball screws http://www.aliexpress.com/store/product/RM1204-Ball-Screw-L480mm-Ballscrew-With-SFU1204-Single-Ballnut-For-CNC-Processing-length-can-be-customized/920371_32612035532.html
-
—
—
Where do you guys source aluminum plate?
Where do you guys source aluminum plate? The Changes to IGentUS (which needs a new name, there’s no IGUS there anymore)…make the old envelope too small.
-
—
—
Hi, Still sorting parts here. I'm a little lost with all these smoothie-based board
Hi,
-
—
—
Anyone have any thoughts on building a printer to be as quiet as possible?
Anyone have any thoughts on building a printer to be as quiet as possible? I’ve always been envious of how quiet an Ultimaker 2 can be, what can I do to achieve that with a Eustathios?
-
—
—
Does your second herculien hotend spot lay dormant...
Does your second herculien hotend spot lay dormant…
-
—
—
Redoing the HercuLien heated bed today with the proper adhesives
Redoing the HercuLien heated bed today with the proper adhesives. Last time I used a light duty carpet tape to bond the PEI sheet to the aluminum taped window glass. This time I’m using the proper 3m 468 MP adhesive tape from zoro.com. The light duty carpet adhesive worked great up until about 95C where it would let loose.
-
—
—
Walter Hsiao , Your work is always so good
+Walter Hsiao, Your work is always so good. Love the updated compact Eustathios carriage:
-
—
—
Welp. just had a fan give up the ghost
Welp. just had a fan give up the ghost. i can say that these fans arent the greatest. when they do have power put to them. the centers are very hot.
-
—
—
Herculien: Z wobble/Ribbing. have tried re aligning the rods
Herculien: Z wobble/Ribbing.
-
—
—
Hello there from switzerland, Great job job qui thoses printers, really nice design!
Hello there from switzerland,
-
—
—
More questions for my build: I broke my thermistor while trying to mount it, and have to order a replacement, has anyone used these: Since I was using the m3 screw to mount it, this would work nicely
More questions for my build:
-
—
—
So, I finally gave my spool PETG a shot today (eSun, natural), and it's driving me mad
So, I finally gave my spool PETG a shot today (eSun, natural), and it’s driving me mad. I’m having the exact same problem I was having with PLA a while back, and I can’t seem to figure out how to fix it. (In fact, I’m not even sure how/if I fixed it when I was running PLA.)
-
—
—
GOLMART for as much as possible? I saw that golmart has got a listing for eustathios specific ball screws and I was wondering if anyone has sourced linear shaft, bearings, couplers etc from them as well?
GOLMART for as much as possible?
-
—
—
Hey All I'm having a hell of a hard time connecting to my azteeg x5 mini
Hey All
-
—
—
welp. my Viki2 keeps giving me a white screen that i have to change back manually in contrast setting in its menu
welp. my Viki2 keeps giving me a white screen that i have to change back manually in contrast setting in its menu. but it keeps coming back.
-
—
—
anyone have a problem with their herculien glass bowing in the middle?
anyone have a problem with their herculien glass bowing in the middle?
-
—
—
Anyone had any problems getting their SSRs to work with their 110v heated beds?
Anyone had any problems getting their SSRs to work with their 110v heated beds?
-
—
—
anyone have a good method of aligning the lead screws for the herculien?
anyone have a good method of aligning the lead screws for the herculien?
-
—
—
can anybody point me to a reliable source of dyneema 1mm braided fishing line in the uk ?
can anybody point me to a reliable source of dyneema 1mm braided fishing line in the uk ? thanks
-
—
—
Alright guys. Having issues with my azteeg
Alright guys.
-
—
—
I want to build a Eustathios Spider V2, but have no printer right now
I want to build a Eustathios Spider V2, but have no printer right now. I’d been looking at a FolgerTech i3 2020 as a “repstrap”.
-
—
—
Hmm control panel above or below the door
Hmm control panel above or below the door. I’m thinking above
-
—
—
Hi all is there a standard method to bonding the silicone heater to the aluminum build plate?
Hi all
-
—
—
This is a job I finished a couple of weeks ago
This is a job I finished a couple of weeks ago. Printed in Bronzefill at 0.111mm layer height with a lot of pre- and post-processing. I will do a full write-up eventually.
-
—
—
Anyone know if a raspberry pi can be powered thru the azteeg?
Anyone know if a raspberry pi can be powered thru the azteeg? im trying to cut back a little on the wiring and plugs.
-
—
—
So I'm sure this is a long shot but does anyone have a HercuLien they would want to sell?
So I’m sure this is a long shot but does anyone have a HercuLien they would want to sell? Interested in anything to save me time, partial or complete. Im having a hard time finding the time to research, print, and build one and I need another printer ASAP. Thanks!!
-
—
—
Hi peeps, Long time reader, first time poster :) I have built myself a Eustathios (Not v2 as I didn't realise that existed when i ordered all my parts) I was wondering if anyone in the UK could point me to a good place to
Hi peeps,
-
—
—
Other than build volume and cost what would be the advantages of my initially building the HercuLien over the Eustathios design?
Other than build volume and cost what would be the advantages of my initially building the HercuLien over the Eustathios design? Is the accuracy and precision the same? Can they use the same filament materials? It seems most of the recent discussions involve the Eustathios model. Also, would ABS be the preferable material for the printed components?
-
—
—
anyone know if a PLA Drag Chain inside the enclosed herculien would work?
anyone know if a PLA Drag Chain inside the enclosed herculien would work? or would it get too warm in there for PLA when printing high bed temp items
-
—
—
Azteeg and pi mounted well ain't it purty
Azteeg and pi mounted well ain’t it purty
-
—
—
I wonder if anyone has yet thought about cloning an Ultimaker?
I wonder if anyone has yet thought about cloning an Ultimaker?
-
—
—
Now its getting interesting
Now its getting interesting 😀
-
—
—
(Off topic) Holy Crabcakes that's some print quality
-
—
—
Hi guys, I've been eyeing up this design for a while on github
Hi guys,
-
—
—
Herculien for sale? Hi guys. My current printer is giving me grief and I'm not confident in it's ability to print PETG or ABS in a quality that I'm comfortable using in my HercuLien build so I'm wondering if anyone has one
Herculien for sale?
-
—
—
On HercuLien, For the feed from the side mounted filament feed unit out to the carriage, how did you decide on a length for the tubing?
On HercuLien, For the feed from the side mounted filament feed unit out to the carriage, how did you decide on a length for the tubing? What are the lengths you all are using?
-
—
—
One more update to my weekend maintenance was more a cosmetic issue
One more update to my weekend maintenance was more a cosmetic issue. I had already cut a fitting front plate for my display when the printer was finished but quickyl exchanged electronics (and display) for a new one. The display then sit there for months fixed with some tape. Yesterday i finally managed to cut a new front plate and an acrylic display cover. I’m quite satisfied with the result - what do you think?
-
—
—
Any advise for printing ABS? I hate the stuff
Any advise for printing ABS? I hate the stuff.
-
—
—
I finally startet my Eusthatios Spider V2 maintenance this weekend
I finally startet my Eusthatios Spider V2 maintenance this weekend. First step was the biggest: replace the carriage with a new one that suits two crossing LM8LUU bearings.
-
—
—
this is what an entire Herculien build looks like after disassembly and arrangement into grouped components
this is what an entire Herculien build looks like after disassembly and arrangement into grouped components. If anyone is interested I’d be happy to document my rebuild with pictures and comments as I go through the the process from individual components, to alignment, break-in, and tuning.
-
—
—
Just saw this on AliExpress. Looks like a good deal for the money ($285+free s/h to USA!), and it is an Ultimaker-ish style gantry design similar to Eustathios
Just saw this on AliExpress. Looks like a good deal for the money ($285+free s/h to USA!), and it is an Ultimaker-ish style gantry design similar to Eustathios. Thoughts?
-
—
—
After a multi-months of little to no time to work on my HercuLien, I am back in the workshop
After a multi-months of little to no time to work on my HercuLien, I am back in the workshop. Of course, I have a couple of questions:
-
—
—
Golmart added a listing for the Eustathios Spider v2 compatible ballscrew
Golmart added a listing for the Eustathios Spider v2 compatible ballscrew. Hopefully I got the diagram right, if anyone sees anything wrong with it, please let me know and I’ll try to get it fixed before someone orders one.
-
—
—
HercuLien or Eustathios V2? Am I ready to build one now, or should I wait?
HercuLien or Eustathios V2? Am I ready to build one now, or should I wait?
-
—
—
For anyone who wants to use firmware retraction with Simplify3D and isn't using firmware that autodetects retraction, it is possible to enable it, at least in some situations
For anyone who wants to use firmware retraction with Simplify3D and isn’t using firmware that autodetects retraction, it is possible to enable it, at least in some situations. Using firmware retraction lets you configure separate retract and unretract speeds, and let you tweak the retraction settings on the fly with M207/M208.
-
—
—
I love it when parts start rolling in!
I love it when parts start rolling in!
-
—
—
Has anyone used printed t-slot corner brackets?
Has anyone used printed t-slot corner brackets? Or know of a beefier printed corner for the extrusion?
-
—
—
Has anyone purchased this 12V heater mat from RobotDigg?
Has anyone purchased this 12V heater mat from RobotDigg?
-
—
—
And its alive! Another Eustathios Spider V2 lives
And its alive! Another Eustathios Spider V2 lives. Finally got it printing, just dialing in the settings and working out a few final issues, but already impressed with the quality. Thanks to all for their helpful posts in this group, +Eric Lien for his design, and also +Ted Huntington for his mega post (https://plus.google.com/101412962363141430834/posts/c7t6cRUP2i8) that helped me get it finally moving a few days ago.
-
—
—
Hi folks, I am a student from Slovenia
Hi folks,
-
—
—
This thing sounds very interesting and might lead to some design changes in my Herculien project :)
This thing sounds very interesting and might lead to some design changes in my Herculien project :)
-
—
—
My Eustathios Spider v2 Hercustruder Bowden tube was somehow stripped and got pulled out of the nut, and so I decided to change the nut trap to hold an embedded m4 lock nut at: .
My Eustathios Spider v2 Hercustruder Bowden tube was somehow stripped and got pulled out of the nut, and so I decided to change the nut trap to hold an embedded m4 lock nut at: https://www.youmagine.com/designs/eustathios-spider-v2-adapted-hercustruder-bowden-tube-nut-trap. The M4 lock nut holds the Bowden tube more tightly, and in addition the nut cannot rotate freely. But definitely a pneumatic adapter would be best there- let me know if somebody has made that already. You may be able to just enlarge the hole, heat it with hot air, and then screw the pneumatic adapter in to make the threads in the plastic.
-
—
—
I'm tuning in my Eustathios Spider 2 and the Z is complicated because there are 2 different gears 32T on the screw pulley and 20T on the motor pulley
I’m tuning in my Eustathios Spider 2 and the Z is complicated because there are 2 different gears 32T on the screw pulley and 20T on the motor pulley. The ball screw is 1204, so 4mm pitch (I see Eric uses a 2mm pitch lead screw). Looking at Eric’s config file my values are somehow double in Marlin. He has 160,160,2560 but mine are closer to half that: 80,80,(1280?) - on a 3D benchy test print I find that 1280 is about 1.2x too small. I reached 1280 by:
-
—
—
Hey everybody. I am building a printer that is a little larger then this one
Hey everybody. I am building a printer that is a little larger then this one. I need an aluminum sheet that is 35cm*35cm for the build plate. I got one and it wasn’t straight:( if anyone knows where I could get one that would be super helpful. Thanks!!!
-
—
—
Alright...you guys build a printer requireing these, and I'll buy you some washers!
Alright…you guys build a printer requireing these, and I’ll buy you some washers!
-
—
—
I'm trying to find a link to a 300mm^2, 110v Silicone heater but can't come up with one on Ali Express
I’m trying to find a link to a 300mm^2, 110v Silicone heater but can’t come up with one on Ali Express.
-
—
—
Hmm 2
Hmm 2
-
—
—
Hmm...
Hmm…
-
—
—
I'm having a hell of a time getting Simplify 3D to work right
I’m having a hell of a time getting Simplify 3D to work right. I can print a Benchy boat quite well in Cura (with the exception of the bit with the smokestack, where it blobs up a bit when it slows down) but I just can’t seem to get it right in Simplify 3D. With the settings shown, which I have tried to match to my Cura settings as closely as possible, I always get this blob when, I believe, it switches from the first to second layer. It’s like the filiment is backed up, but again, this doesn’t happen in Cura for, what I can tell, the same settings.
-
—
—
Hey All, I just about have my first printer together and I am hoping that someone with experience on the ramps board can confirm my wiring
Hey All,
-
—
—
When your design is nigh-unprintable. I'm still puttering, coming up with solutions for my one-off mutt of a printer
When your design is nigh-unprintable.
-
—
—
After a few weeks of work, I am able to see the printer moving
After a few weeks of work, I am able to see the printer moving.
-
—
—
First time in ages I've of able to get to printing and check the community
First time in ages I’ve of able to get to printing and check the community. I’m so proud to see how our community has grown so much. Welcome to all of the newer members!
-
—
—
Seeing this Eustathios Spider v2 in action- I think it would be cool to make a larger 40x40cm version - and somewhat simple: you would just need to add 10cm to the horizontal extrusions and linear rails
Seeing this Eustathios Spider v2 in action- I think it would be cool to make a larger 40x40cm version - and somewhat simple: you would just need to add 10cm to the horizontal extrusions and linear rails. You could even add 10cm more to the Z. - In fact a person could probably add a lot more to the Z if they wanted to- without any performance issues- I mostly don’t need a large Z for the work I do- but it seems possible.
-
—
—
I finally got my first print in ABS on my Eustathios Spider V2
I finally got my first print in ABS on my Eustathios Spider V2. It took a little while to get all the linear rails perfectly aligned and the carriage moving with very little friction. I like this printer much more than the moving bed designs of the RepRaps and I think this design is a great starting point to branch from for all my future 3D printers.
-
—
—
Aaagh so close it's a tease...then I have to take it apart again when the acrylic arrives But here it is with a mendel90 sturdy frame that was improperly drilled(was drilled using the wrong guide) A much bigger printer than
Aaagh so close it’s a tease…then I have to take it apart again when the acrylic arrives
-
—
—
Finally got my printer configured for PLA
Finally got my printer configured for PLA. 65 mm/s, 0.100 layer hight. 3.4 mm retraction with 4 mm wipe. ABS is still a huge pain in the rear for me. But I will get there. Also planning to enclose Eustathios V2 completely which should help with ABS printing
-
—
—
Is the hobb gear from the only one that fits in the HercuStruder?
Is the hobb gear from makerstoolworks.com the only one that fits in the HercuStruder? I ordered some at RobotDigg, but they don’t fit :(
-
—
—
First print with colorFabb Filament 's new nGen filament, looks promising
First print with +colorFabb Filament’s new nGen filament, looks promising
-
—
—
Is the z gantry of the herculien tight on the leadscrews for anyone else?
Is the z gantry of the herculien tight on the leadscrews for anyone else? i seem to have to tug on the belt with alot of force.
-
—
—
I'm thinking of oerdering a new 32Bit controller board
I’m thinking of oerdering a new 32Bit controller board. So a few questions about that:
-
—
—
Another Eustathios Spider 2 is on its way to being born- just not yet!
Another Eustathios Spider 2 is on its way to being born- just not yet! I’m having a lot of fun and learning a lot of new things from assembling this printer. I haven’t made a print yet, I just today got the limit switches wired, and there is still a problem not shown in the video- I saved everybody’s ears - the motor grinds to a halt in one particular part of the break in gcode- the part where X is near 0 and just Y is moving - where the carriage is moving in a square around the outer perimeter - I have no idea why yet. There must be less friction when the rods are also turning as opposed to moving straight on without any rotation. This is just with Marlin, Ramps, 12V. It’s starting not to grind there- so perhaps it eventually gets “broken in”?- spoke too soon- it just grinded there agin! But it seems to be grinding less often at that particular area.
-
—
—
My Eustathios Spider V2 can't seem to get up to temperature unless I put my finger on the hotend fan and stop it from blowing air
My Eustathios Spider V2 can’t seem to get up to temperature unless I put my finger on the hotend fan and stop it from blowing air.
-
—
—
Just a note, the new GOOGLE+ web interface is buggy
Just a note, the new GOOGLE+ web interface is buggy
-
—
—
If you have the capability to cut wood panels you probably have what you need for plastic
If you have the capability to cut wood panels you probably have what you need for plastic. Home Depot has various plastic panels varying in thickness and opacity. If the panels are simply to retain heat or make it look cool you could use suspended ceiling light fixture panels. They are 2’x4’ and translucent with a texture. More expensively is Lucite clear plastic panels.
-
—
—
Got a question for anyone that has enclosed their Eustathios or HercuLien
Got a question for anyone that has enclosed their Eustathios or HercuLien. Did you use a local source for the panels? If you went online, who did you order from? Please note I am U.S. centric. Did they custom cut or did you cut it yourself? I ask because, if it’s wood panels I have all the necessary tools but I have much less success cutting plastic panels and would like to find a source that will cut them to spec as inexpensively as possible.
-
—
—
Did anyone else find that the small step motor belts are a little too big?
Did anyone else find that the small step motor belts are a little too big? I bought the motor gear on ebay but it has the same specs as the one on the BOM- I haven’t tested it but it seems too loose.
-
—
—
Sneak peek from the lab (#IGentus Mark 2)
Sneak peek from the lab (#IGentus Mark 2)
-
—
—
Can anyone validate something for me? This is a Cross-Piece for the next iteration of IGentUS, It's designed to use 10mm rods and IGUS bearings and when printed at 100% scale, 100% flow on my printer in PLA, it's a press-fit
Can anyone validate something for me? This is a Cross-Piece for the next iteration of IGentUS, It’s designed to use 10mm rods and IGUS bearings and when printed at 100% scale, 100% flow on my printer in PLA, it’s a press-fit affair.
-
—
—
Sorry, kind of off topic again but I know people here are using these inserts
Sorry, kind of off topic again but I know people here are using these inserts. So I ordered:
-
—
—
The Community Mods folders are up for the Github of HercuLien and Eustathios Spider V2
The Community Mods folders are up for the Github of HercuLien and Eustathios Spider V2. If you are familiar with Github and have some upgrades you would like to add please feel free to submit a pull request.
-
—
—
I made an inductive endstop mount for z-axis
I made an inductive endstop mount for z-axis. May also be used for auto bed leveling. It is mounted with existing screws . One on cooling duct mount and one on hotend fan mount. I tried a few versions, but this place for mountig is the one where i lost minimal build volume. Only 3-4mm on y axis. When +Eric Lien has set up his github for modified parts, i will upload there.
-
—
—
So I've been on and off with my Herculien build and I finally installed the bed to notice the hotends not get near the bed
So I’ve been on and off with my Herculien build and I finally installed the bed to notice the hotends not get near the bed. Did I mount the bed wrong or did I somehow screwup the gantry? Thank for the help.
-
—
—
Just installed the first version of a dual v6-Volcano carriage for the Herculien
Just installed the first version of a dual v6-Volcano carriage for the Herculien. Printed with my beta sample of PushPlastic PETG through a Volcano with the 0.4mm nozzle. So far so good. Nice and clean looking with an additional 10-15mm in the Z axis (not that the Herculien needs more print volume). So far performance has been excellent. Minor changes necessary for the final version
-
—
—
For the Eustathios Spider v2, is there a trick to keeping the "I" frame, 3 extrusion pieces of the bed from getting loose?
For the Eustathios Spider v2, is there a trick to keeping the “I” frame, 3 extrusion pieces of the bed from getting loose? I find that I tighten the 2 M5 screws holding them together as tight as I can, but the extrusion forms like a lever and somehow makes it easy to loosen the connection to the middle bar. I suppose that when the Aluminum plate is connected with springs the force to loosen it would be less.
-
—
—
Hey everyone, I was thinking about making a section of my githubs for part alterations and modifications made by the community
Hey everyone, I was thinking about making a section of my githubs for part alterations and modifications made by the community. That way everything is in a centralized location for someone looking to make modifications to the HercuLien and Eustathios Spider v2. If you aren’t familiar with github, but want to have your stuff included please comment to this post with a link to the STL and SolidWorks, Step, or other native model if possible as well. Maybe also include a text file with your name, the reason for the modification, and any other details you want to provide. That way I can make sure the creators are getting credit for all their amazing work.
-
—
—
Hey Eustathios Spider builders, did anyone who ordered Ball Screws from Golmart need to redesign the Z_Axis_Bed_Support to accommodate the larger Ball Screw Nut?
Hey Eustathios Spider builders, did anyone who ordered Ball Screws from Golmart need to redesign the Z_Axis_Bed_Support to accommodate the larger Ball Screw Nut? The original BOM lists a Misumi lead screw which would accept either an MTSFR, MTSGR or MTSNR Flanged Lead Screw Nut, all of which are significantly smaller. Fortunately I did not pre-print that particular part and comparing the model file to the actual part tells me it doesn’t fit. Aside from the very obvious moving of the mounting holes, the overall Ball Screw Nut is bigger. If someone else has already done the redesign I would appreciate a link to a copy. If not I will take the one +Walter Hsiao designed and modify it accordingly. Just trying to save myself a bunch of work/delay.
-
—
—
Hey All, Is there any software out there that allows you to write custom Gcode script and export as .gcode for importing it into repetier or simplify3D?
Hey All,
-
—
—
My first actual 3d model where dimension and placement matter
My first actual 3d model where dimension and placement matter.
-
—
—
Never, ever, ever, comment to your significant other about how well the 3d printer is working finally
Never, ever, ever, comment to your significant other about how well the 3d printer is working finally. You’re just asking for trouble.
-
—
—
Here is that enclosure I linked a bit back
Here is that enclosure I linked a bit back.
-
—
—
Do you guys think a Go Pro would last within the build chamber of the herculien?
Do you guys think a Go Pro would last within the build chamber of the herculien? it gets what …65c ambient?
-
—
—
I'm asking this question in this group because I know all the cool people hang out here ;-) No seriously, its cos I feel there are some and mostly awesome minds in this club
I’m asking this question in this group because I know all the cool people hang out here ;-)
-
—
—
After struggling with PETG on an E3D Volcano I decided to revisit the idea of a dual V6/Volcano carriage for the Herculien
After struggling with PETG on an E3D Volcano I decided to revisit the idea of a dual V6/Volcano carriage for the Herculien. Waiting on some brass inserts (no more captive nuts) before I can test it. Oh, and I need to buy a V6 now…
-
—
—
Work is busy, but managed to squeeze off a print today
Work is busy, but managed to squeeze off a print today. Some ringing at the corners, and you can probably see where I went to 200% but then brought it back down to 150% after a few layers. I need a better camera than the potatoe that they built into my phone.
-
—
—
anyone have an stl for the VIKI v2?
anyone have an stl for the VIKI v2? similar to the Eustanthios spider mount. but able to be used with the panels in for the Herculien
-
—
—
For those looking for the "hoffman qline" enclosure but only finding it for 200usd and up i have a solution for you it is only slightly larger in all dimensions ( but hey more wiggle room right?) and its only 20USD :D Happy
For those looking for the “hoffman qline” enclosure but only finding it for 200usd and up i have a solution for you
-
—
—
That moment when the lexan panels for the herculien come in and you realise you have under estimated the size of this thing o.o its HUGE
That moment when the lexan panels for the herculien come in and you realise you have under estimated the size of this thing o.o its HUGE
-
—
—
Has anyone tried printing PETG through an E3D Volcano?
Has anyone tried printing PETG through an E3D Volcano? I’ve had great results with PETG on my other printers with an E3D V5 and V6, but no matter what I adjust I just can’t get rid of ooze printing it through the Volcano.
-
—
—
First calibration print had me adjust flow to 0.97, then printed this off
First calibration print had me adjust flow to 0.97, then printed this off. Really happy. Minor stringing to be tuned out. Layers show some contraction at the base. Maybe too much heat on the bed. 210C at the nozzle and 60C on the glass.
-
—
—
Woo Christmas is early lol +1 to trim craft They were less than half the price of my local guy
Woo Christmas is early lol
-
—
—
Don't know why I didn't do this sooner
Don’t know why I didn’t do this sooner. The squeaking from the filament holder during prints was driving me nuts. Added a few loops of Teflon tape (red bit) around the holder and it’s totally quiet now!
-
—
—
I have a quick question about placement of the Z axis ballscrews in the Eustathios
I have a quick question about placement of the Z axis ballscrews in the Eustathios. I noticed on the HercuLien that the lift axis is centered on each side, of course it is more robust than the Eustathios, rightfully so. But in all the diagrams of the Eustathios Sv2 the guide rod is centered and the ballscrew is offset. Was this on purpose or just how it ended up fitting together?
-
—
—
This is a work in progress. If anyone wants to run with this I will provide a link to my Fusion 360 source files
This is a work in progress. If anyone wants to run with this I will provide a link to my Fusion 360 source files. The model timeline is a mess since it was try this, then that, then figuring out something I did near the beginning wasn’t going to work, etc.
-
—
—
After a long time away I finally got it finished
After a long time away I finally got it finished. Break-in gcode ran with zero problems. Test prints tomorrow, then some calibration.
-
—
—
Hello folks, back in june i had problems printig circles (see: )
Hello folks,
-
—
—
does the stock dual carriage work with other hotends like jheads?
does the stock dual carriage work with other hotends like jheads? or the pico? they both have groovemounts. like the e3d. they just dont have the tube clip to my knowledge.
-
—
—
I don't know who or where you guys found Alirubber for the heaters, but they sure are fast
I don’t know who or where you guys found Alirubber for the heaters, but they sure are fast. Ordered a heater just a week ago and it will be here on Wednesday. Been exchanging emails with Sivia Liang and it has been one of the easiest transactions I have ever done. I just hope Golmart is just as easy with the ball-screw.
-
—
—
will this 3d printer project work. 3d pdf linked
will this 3d printer project work.
-
—
—
I've been dialing in the acceleration on my Herculien and wanted to share some of the results
I’ve been dialing in the acceleration on my Herculien and wanted to share some of the results. To examine the effects of different acceleration I printed a model provided by +Eric Lien that is used to test backlash. The part shown in the photograph was printed at 100mm/s perimeter speed and I updated the acceleration via an M204 S
command at different times during the print. Based on these results I've turned down my acceleration in X and Y from the default 9000 mm/s^2 to a cool 3000 mm/s^2. This reduces ghosting to a minimum on sharp corners. While this increases print times based on acceleration limited velocity, when you run the numbers it doesn't translate to much loss. Based on Smoothieware's default 1000 ticks/s update rate for acceleration, a speed of 100 mm/s is reached in a distance of ~1.5 mm (0.45mm for 9000 mm/s^2). -
—
—
If my printer is unable to succesfully print off a set of Herculien Parts in ABS Whom here could print me some Herculien parts in ABS?
If my printer is unable to succesfully print off a set of Herculien Parts in ABS
-
—
—
What hotend does everyone here use? im weary of getting another e3dv6
What hotend does everyone here use?
-
—
—
Any advice on the correct type of grease to use on LM8UU/LM10UU linear bearings?
Any advice on the correct type of grease to use on LM8UU/LM10UU linear bearings?
-
—
—
whats the benefits of using 24v as opposed to 12v?
whats the benefits of using 24v as opposed to 12v?
-
—
—
Love Gino over at . I needed to restock on various metric hardware because I was getting low, and have some new projects in process with Alex Lee .
Love Gino over at trimcraftaviationrc.com. I needed to restock on various metric hardware because I was getting low, and have some new projects in process with +Alex Lee. Gino helped me out and added some bolts to the site that I needed but weren’t listed, and shipped the next day. They are just over in Wisconsin, so via Spee-Dee delivery I had the parts the following day and only $2.99 flat rate shipping.
-
—
—
For the heater. would this do? it matches in spec minus 30mm im just not sure if there was another typo Eric Lien
For the heater. would this do? it matches in spec minus 30mm
-
—
—
What is the proper steps/mm to use when using the Golmart 1204 ball screw with 32t GT2 Pulleys?
What is the proper steps/mm to use when using the Golmart 1204 ball screw with 32t GT2 Pulleys?
-
—
—
Hey I apologize if this is the wrong place
Hey I apologize if this is the wrong place. Just found the herculien a few hours ago and diving into it. But I have a question about the support rail, so I figured I’d ask here.
-
—
—
Hmmm for the azteeg. sd8825 or sd6128 i have heard n seen issue with the 8825 ( probably other makers) thoughts?
Hmmm for the azteeg. sd8825 or sd6128
-
—
—
That is an interesting nozzle. Might solve some problems with abrasive filaments Originally shared by Jonathan Hurst Ryan Carlyle thanks for all the input and the back ground knowledge you shared
That is an interesting nozzle. Might solve some problems with abrasive filaments
-
—
—
In case anyone is interested. I took the temp vs
In case anyone is interested. I took the temp vs. resistance values Alirubber gave me for the Herculien heated bed (100k thermistor, 3950 beta value) and fit it to the Steinhart-Hart Equation. The values for the A, B, and C coefficients come out to ~ 0.0006454337947, 0.0002239473005, and 0.000000087, respectively.
-
—
—
Noozle clogging. New method to clean. Variation of Atomic/cold pull
Noozle clogging. New method to clean. Variation of Atomic/cold pull.
-
—
—
I am looking to get the Eustathios Aluminum build plate
I am looking to get the Eustathios Aluminum build plate. Does anyone have any ideas where I can get one made, or have they bought one recently?
-
—
—
What do you all think about the MK8 extruder?
What do you all think about the MK8 extruder? They are derived from Makerbot and feed filament directly into the hot end (using a convenient spring release lever). So if one requires the extruder to not be located on the hot end then this is obviously of no use. They drive directly from the step motor (without any gear reduction) using a standard hobbed gear that sells on Ebay for <$2. Here are two variations:
-
—
—
First print after my machine was rebuilt
First print after my machine was rebuilt. Some kinks are still there but now I know that if I slow down it will be perfect. 0.192 mm height, 40 inner, 35 outer, 50 infill, 3 mm retraction on 50mm/s. Bed 60. Sliced with Cura.
-
—
—
Poly-V Ribbed Belt
Poly-V Ribbed Belt.
-
—
—
Do you think I can use petg to print printer part?
Do you think I can use petg to print printer part?
-
—
—
Is anyone willing to accept payment for assistance in getting my printer to work?
Is anyone willing to accept payment for assistance in getting my printer to work? I have skype and laptop with a camera. My issue is software in nature. Maybe a few mechanical issues but now I do not know. You must have a smoothie board 5XC working (preferably with a Vicki V2 LCD).
-
—
—
What is a good test print for high speeds?
What is a good test print for high speeds? I just installed a 0.4mm Volcano nozzle on my Herculien and I’m looking to push the limits. @0.2mm layer heights I’m printing external perimeters at 50 mm/s for quality, but I’ve bumped all other print speeds up to 80-125 mm/s and my initial test prints are turning out fantastic… I’ve officially given up my plan for a v6-volcano dual extruder after seeing the print quality I’m getting now.
-
—
—
Have any of you all attempted to make a paste extruder?
Have any of you all attempted to make a paste extruder?
-
—
—
Saw this rather interesting concept on aliexpress
Saw this rather interesting concept on aliexpress. This is made for the 6mm rods on the Ultimaker2, but I wonder if this could be implemented on some of the designs here. And then there is the question of how good this is
-
—
—
Has anyone taken a look at this?
Has anyone taken a look at this? Looks very familiar;)
-
—
—
I had some problems with stress cracks and I am reprinting everything in abs
I had some problems with stress cracks and I am reprinting everything in abs. Now that I have access to a printer that will print ABS again. I ran into the same problem Ashley did, removing the brass bushings. I dunked the whole thing in boiling water for 20 seconds and it was surprizingly easy to twist with plyers and get them out. I tested and they slide okay, but did I ruin the bushings? Did it exude the oils? I can’t tell just by looking at them.
-
—
—
Is there a better way to fasten the bowden tube to the Hercustruder?
Is there a better way to fasten the bowden tube to the Hercustruder? I am using a 4mm nut, but it pops out of the bowden every so often. Should I glue the nut to the bowden?
-
—
—
Simple question: how are people fastening the top extrusions in the Eustathios- the screw head is too large to fit into the groove of the extrusion
Simple question: how are people fastening the top extrusions in the Eustathios- the screw head is too large to fit into the groove of the extrusion. Do we need to drill the hole wider, grind the screw head smaller, or just use long screws and tighten them on the outside of the extrusion?
-
—
—
Eric Lien i haven't used Solidworks so far (and have no access to it) - is it easy for you to modiy a part and to offset features a bit?
+Eric Lien i haven’t used Solidworks so far (and have no access to it) - is it easy for you to modiy a part and to offset features a bit? If so could you probably modify the XY end belt tensioner (https://github.com/eclsnowman/Eustathios-Spider-V2/blob/master/STL%20Print%20FIles/XY%20Axis%20Belt%20Tensioner%20A.STL) and move the whole for the crossbars 3mm away from the outer bars? I’m going to design an LM8LUU-Carriage and i think it would be better to be able to cross the bearings which wouldn’t be possible with the curerent distance of bars. 6mm more would give roughly 1-2mm between the bearings and should still work fine.
-
—
—
Probably a dumb question, but how is the door stop supposed to work on the Herculien?
Probably a dumb question, but how is the door stop supposed to work on the Herculien?
-
—
—
Hey everyone, i had the need for some more effective cooling today and as my custom carriage is still some time away i quickly did a new fanduct that offers some more concentrated air flow
Hey everyone,
-
—
—
I printed all the pieces for the HercuLien in PLA a while back
I printed all the pieces for the HercuLien in PLA a while back. I don’t see myself building the HercuLien anytime soon so I wanted to see if anyone is interested in purchasing the 3D Printed pieces. The only thing missing is the second Flange and Spool holder. Everything else is there.
-
—
—
Repetier Host.... If I want to speed up my Eustathios Printing speeds, what should I adjust?
Repetier Host….
-
—
—
Here is a cable management system I came up with for my Eustathios v2 Spider
Here is a cable management system I came up with for my Eustathios v2 Spider.
-
—
—
Finally managed to do it, PrintBite - a useful and cost effective print surface for all your printing needs is now available at
Finally managed to do it, PrintBite - a useful and cost effective print surface for all your printing needs is now available at http://www.mutley3d.com/PrintBite/
-
—
—
Is the HFSB5-2020-355-AH177_5 in the BoM for the Eustathios Spider V2 supposed to be HFSB5-2020-355-AH177.5?
Is the HFSB5-2020-355-AH177_5 in the BoM for the Eustathios Spider V2 supposed to be HFSB5-2020-355-AH177.5?
-
—
—
I just received 4 of these in the mail....
I just received 4 of these in the mail…. Can’t wait to compare them to the SD8825 I have been using for years now. The low noise operation modes and up to 1/128 microstepping are really cool upgrades from most of the steppers used out there right now.
-
—
—
Glad to have happened across the Eustathios design yesterday
Glad to have happened across the Eustathios design yesterday. I’ve recently been thinking about buying an Ultimaker 2, but the pricing is higher than I think is reasonable for it’s build volume. I currently have a Printrbot Simple Metal with the Matrix Precision volume upgrades (8”x8”x10”). It’s a nice printer, but also very limited in terms of speed and noise. I’ll probably keep it around specifically for dealing with things like flexible filaments.
-
—
—
I was talking to one of the smoothieware developers recently and he had some suggestions to my config file that others here may find helpful
I was talking to one of the smoothieware developers recently and he had some suggestions to my config file that others here may find helpful.
-
—
—
X and Y axis have come to life
X and Y axis have come to life. Speed and acceleration kept low to avoid stalling stepper motors. So far so good. Waiting for some fundamental parts (e.g. ball screw z-axis, extruder stepper, hot end) before I can continue. 1/32 micro steps seems to small (insufficient torgue), 1/16 doing fine so far in combination with 0.9 degree stepper motors. If my calculations are correct, the setting is 160 steps per mm (0.9 degree, 16 micro steps, 20 teeth / 32 teeth pullies).
-
—
—
Got some of my electronics for the Spider I am building, been playing with firmware and icons on this touch screen
Got some of my electronics for the Spider I am building, been playing with firmware and icons on this touch screen. I sure wished that Makerbase would release source code. But alas that is likely never going to happen. So I can only change a very few things that a HEX editor will allow me to do without breaking the current firmware.
-
—
—
I purchased Simplify3D to use on my Eustathios Spider V2..
I purchased Simplify3D to use on my Eustathios Spider V2.. When I try to print something it scraps off the 3D-EEZ film with the hot end. I’m not sure why this is happening.
-
—
—
I'm running into a problem. When running the gcode for break in I get a weird shuddering
I’m running into a problem. When running the gcode for break in I get a weird shuddering. This happens mainly after moving along the x axis and switching to a diagonal movement. Any ideas on where to start troubleshooting?
-
—
—
Im stuck with the Herculien Z axis,it wont print above 1440 steps per mm So far I managed to print a PLA test-cube 20 x 20 x 20 MM : measuring the result gives me 19.58 x 19.30 x 7.7 mm Gamma steps per mm 1440 All
I´m stuck with the Herculien Z axis,it wont print above 1440 steps per mm
-
—
—
Something I can't quite wrap my head around that I'm hoping you all can help me out with...
Something I can’t quite wrap my head around that I’m hoping you all can help me out with… Currently I’m using 4 start lead screws with a 2 mm pitch for an effective pitch of 8 mm (4*2mm). Using the Prusa calculator here (http://prusaprinters.org/calculator/) I get a 0.072mm step size for the 20 tooth motor drive gear coupled with 36 teeth gears driving the lead screws. While this seems like low resolution, it produces phenomenal prints. Especially considering that I’m using a Volcano hotend, so <100 micron layer heights were not my aim (however, 0.072 I know I can do at full steps on the z axis) , but fast printing was. Anyways, intuitively I would think that a 20 tooth gear on my motor with larger (>36 teeth) on the z-axis would mean more steps/mm that the 36 tooth gear, but the calculator says otherwise. What am I missing here? I really can’t make sense of this, especially when I look at the gearing on my bicycle… Can someone help me make sense of this?
-
—
—
It's finally moving! ProTip guys, don't run the Z motor without micro-stepping
It’s finally moving!
-
—
—
Hay I'm new to this circle and I was wondering where I can download the stl files and if someone has made a products list
Hay I’m new to this circle and I was wondering where I can download the stl files and if someone has made a products list. Thanks
-
—
—
Hey Eric Lien - i'm finally finding the time to overhink the carriage a bit as i already promised some weeks ago
Hey +Eric Lien - i’m finally finding the time to overhink the carriage a bit as i already promised some weeks ago. I’m currently just looking around for ideas and playing around a bit in Fusion360.
-
—
—
Definitely having z-banding issues on my eustathios v2
Definitely having z-banding issues on my eustathios v2.
-
—
—
Hey All, I am trying to upload new firmware to my RAMBO board and I am getting this error message.....I changed the COM port and the board type already;
Hey All,
-
—
—
First Herculien print with some cheap PLA , trying to figure out the correct steps per mmm on the Z-axis
First Herculien print with some cheap PLA ,
-
—
—
I've been slowly doing a Print-it-Forward set of parts and now have a couple of questions (haven't seen one of these printers in person yet)
I’ve been slowly doing a Print-it-Forward set of parts and now have a couple of questions (haven’t seen one of these printers in person yet).
-
—
—
Why I have love-hate relationship with my delta printer...
Why I have love-hate relationship with my delta printer…
-
—
—
Can someone explain to me, using the latest image of octopi, EXACTLY how to set up the damn WiFi?
Can someone explain to me, using the latest image of octopi, EXACTLY how to set up the damn WiFi? I’ve followed a number of how to guides, and nothing seems to work. I tried following the video by Thomas Sanladerer and the desktop doesn’t have the WiFi config shortcut. I tried the guide by TESTED and the complicated guide they link to. Neither work.
-
—
—
I received my X5 Mini with the screw type terminals
I received my X5 Mini with the screw type terminals. Now all I get when I turn on the printer is a blue type of screen with no text on my Viki LCD.
-
—
—
Hi All, quick question. When using 2020 extrusion, do you guys use a aluminium corner bracket or a printed one ?
Hi All, quick question.
-
—
—
Hi All! I have a question about hooking up the Viki LCD to the Azteeg X3
Hi All!
-
—
—
Ive got my herculien running, all rods smooth and fast, yippie !!
I´ve got my herculien running, all rods smooth and fast, yippie !!
-
—
—
Quick dumb question for you guys running octoprint on the Raspberry Pi
Quick dumb question for you guys running octoprint on the Raspberry Pi. How do you go about connecting the Pi to the printer board (Azteeg X5 mini)? Is there a way to keep all the connections internal? I’m working on the wiring right now, and I need to figure this out.
-
—
—
Well, here are some more picture of Eirikur Sigbjrnsson test prints which I hope shows more details (good and bad)
Well, here are some more picture of +Eirikur Sigbjörnsson test prints which I hope shows more details (good and bad).
-
—
—
Another Eustathios growing up. Now waiting for stepper motors, pulies, belts, etc to arrive
Another Eustathios growing up. Now waiting for stepper motors, pulies, belts, etc to arrive. Ordered the bronze bushings at Lulzbot. Using the 2020 frame offered by Motedis.com, and the quick fasteners. This avoids the need the throughholes in the frames. You can see them in all corners of the top bars. +Frank Helmschrott thnx for suggesting this supplier.
-
—
—
So the first print ran and failed, the off to Maker Faire Orlando for my first prints
So the first print ran and failed, the off to Maker Faire Orlando for my first prints. Talk about cutting it close.
-
—
—
Playing around with Cura 15.06 today and printing replacement parts for my Herculien
Playing around with Cura 15.06 today and printing replacement parts for my Herculien. So far I’m very happy with this implementation of Cura. Has anyone else tried Cura 15.06? It seems that most here are using Simplify3D. Perhaps once I get beyond my grad student salary I will invest in S3D as most seem to be very happy with it.
-
—
—
eu (edit: eu? I don't remember typing eu...) Originally shared by Mike Miller Here we go!
eu
-
—
—
Decided to test some XT material from ColorFabb in my search for the best material for printing the parts needed for the Herculien
Decided to test some XT material from ColorFabb in my search for the best material for printing the parts needed for the Herculien. This is actually a great material and a bit better than PETG. I printed these on an Ultimaker2 with Simply3d. I used the ABS profile as a base, changed the nozzle heat to 250°c, the bed to 70°c and turned the fans on to 50%, infill at30%. No other ajustments. Everything printed out great. There is similar material shrinkage as is with ABS. The black one is a CF20 carbon fibre (I think the nozzle is still ok btw). The next two are green and transparent XT (not so much transparent with the infill :)). The blue one is a PETG for comparison. The Carbon Fibre part looks best of the lot, with a slight sandpaper feel to the surface.
-
—
—
Providing you with an update of my build proces
Providing you with an update of my build proces. Most of the parts have been printed by my Prusa I3 (takes some time but size is not the issue), smooth rods have been delivered, 2020 frame has been cut by Motedis (Germany) and is on its way, lots of small parts have been ordered at RobotDIgg. As soon as the frame parts arrive, assembly can start. Not sure yet on the bronze bushings from a sourcing point of view. Any ideas for European sourcing?
-
—
—
Would anyone using smoothie for the Herculien be able to send me the smoothies code for me to flash on to the board?
Would anyone using smoothie for the Herculien be able to send me the smoothies code for me to flash on to the board? I am close to finishing the printer although I have not been getting responses back when I send simple g commands. The printer can run the breakin code just fine, I just have problems when it comes to auto pid and other things.
-
—
—
Looking through the documentation, I can't find anything on the length of the bowden tube
Looking through the documentation, I can’t find anything on the length of the bowden tube. Can someone supply the length?
-
—
—
Had some problems with the section that the twist tie was supposed to go through,it got clogged during printing
Had some problems with the section that the twist tie was supposed to go through,it got clogged during printing. After much work I ended up drilling two holes to clear the clog. That left me with a very loose fitting and a wobbly hot end. So I made a small adapter, then used screws to hold it in place. I’m not happy with the end results as there is too much air gap(should be much less) and the original head should have been reworked for screws instead of just drilling a hole and making it work. But the end results is working solid, just not pretty.
-
—
—
One step closer. Got most of the wiring in place
One step closer. Got most of the wiring in place. Hopefully my raspberry pi holder will be done tomorrow and I can finish up.
-
—
—
Working on some Eustathios text to put on my printer and I figured I'd ask some opinions
Working on some Eustathios text to put on my printer and I figured I’d ask some opinions. Here are my current thoughts, in no real particular order.
-
—
—
Does any of you guys know of a source for 0,9/400steps/rev Nema17 steppers with more power than the ones that Robotdigg offers?
Does any of you guys know of a source for 0,9°/400steps/rev Nema17 steppers with more power than the ones that Robotdigg offers? (http://www.robotdigg.com/product/241/0.9%C2%B0+Step+Angle+Nema17+48mm+Stepper+Motor) I’m sure they’re good enough for normal use but i see too many lost steps on X/Y due to just small “crashes” with existing material. It’s too much if only the nozzle touches some parts a little bit which could happen quite easily on some prints. I had one 15 hour print failing 5 times now and that’s enough..
-
—
—
hello to everyone, I'm building an eustathios but have a little problem whit the extruder, for my project i use a lm8u , can you help me to find an extruder compatible with lm8u?
hello to everyone, I’m building an eustathios but have a little problem whit the extruder, for my project i use a lm8u , can you help me to find an extruder compatible with lm8u?
-
—
—
I have one of the AliRubber silicone heated beds
I have one of the AliRubber silicone heated beds. I know the thermistor beta spec is 3950 and its resistance is supposed to be 100k at 25C. I set up the appropriate value in smoothieware config file and I’m getting readings of 130C at room temperature. The second thermistor also reads the same. Does anyone here have any idea what to try next?
-
—
—
Trying Repetier to run break in code
Trying Repetier to run break in code. gcode is loaded but won’t run. I wish their was a customer support for this… Can someone share their screen shot’s of their repetier configuration? Maybe I am missing something?
-
—
—
I'm trying to run the breakin code using the config file provided to me earlier (Eric Lein V2 on Github)
I’m trying to run the breakin code using the config file provided to me earlier (Eric Lein V2 on Github). I erased what I had and saved Eric’s code as the config file on the memory on the smoothie board. The memory is in the board and I tested that the printer was online. All axis move. Now I’m trying to run the break in code and I’m not finding success. I made sure I had the recommended software installed per: http://reprap.org/wiki/Printrun and I do. But I get errors via the command console and the pronterface GUI software. I tried several command lines on the command console with the same effect.
-
—
—
Does anyone have a better setup guide for the Azteeg X5 mini and Viki2.0 LCD?
Does anyone have a better setup guide for the Azteeg X5 mini and Viki2.0 LCD? I’m trying to follow the quick setup guide on Panucatt’s website, but it’s not really working for me.
-
—
—
I know it was posted here before, but would anyone mind sharing the cost they paid for the Ball Screws for the Eustatios Spider V2
I know it was posted here before, but would anyone mind sharing the cost they paid for the Ball Screws for the Eustatios Spider V2. Did machining the ends cost more? What was delivery time like.
-
—
—
Has anyone yet made alternative filament spool holder for the Eusthatios Spider V2?
Has anyone yet made alternative filament spool holder for the Eusthatios Spider V2? I’ve got some spools that don’t fit like (holes) 88x60mm, 95x30, 125x30.
-
—
—
Today during a quick test print I started noticing the typical smell of smoking electronics and had a quick look under my Eustathios only to see some sparks coming off the (bed heating) SSR connectors
Today during a quick test print I started noticing the typical smell of smoking electronics and had a quick look under my Eustathios only to see some sparks coming off the (bed heating) SSR connectors. Turned out that one of the terminal screws on the load side had loosened and the cable barely touched the terminal, which started emitting tiny metal sparks. I was really surprised for this to happen as I remember tightening these screws quite strongly. I had used a DC SSR on 24V and luckily it survived the whole incident.
-
—
—
Started to print the 3D parts. Don't worry about number 6, it was printed in the first cycle
Started to print the 3D parts. Don’t worry about number 6, it was printed in the first cycle.
-
—
—
I use Simplify3D as my default slicer
I use Simplify3D as my default slicer. But for the Cura users out there I made an STL of the bed for Eustathios. It can be used in Cura similar to the way the Ultimaker bed displays when you select that as your printer. To be honest it is just a waste of graphics resources… but it looks cool.
-
—
—
So, I'm having a hell of a time getting the 8-pin molex connector to work
So, I’m having a hell of a time getting the 8-pin molex connector to work. I’ve crimped the wires into the pins, but now I can’t get the pins into the plastic connectors. It’s like the don’t fit or are for the wrong connector. I’m almost certain I got the right ones from digikey, the ones specified on the BOM. any thoughts or ideas?
-
—
—
Finally making some progress. The Z axis is now moving without complaints
Finally making some progress. The Z axis is now moving without complaints. Made a one-off piece to constrain the lead screw, being carefully to give it an adjustable range in the x and y axis.
-
—
—
The bowden tube keeps pulling out of my E3D V6 Extruder
The bowden tube keeps pulling out of my E3D V6 Extruder. Did I wear out the piece that holds the tube in place?
-
—
—
Now it is my turn to show off
Now it is my turn to show off. Finally something is moving. Running Break In gcode on 3k. Smooooth))))
-
—
—
I am now proud to say that things evolve in the right directions, the interest is growing for my products and this have lead me to increase the production batches and this makes it possible to reduce the cost of my products
I am now proud to say that things evolve in the right directions, the interest is growing for my products and this have lead me to increase the production batches and this makes it possible to reduce the cost of my products. I would like to thank all you fantastic customers that have made this possible.
-
—
—
Do you think this is a temperature thing?
Do you think this is a temperature thing? The print comes out awesome but has this all over it. The previous print job that is not in this picture was without an extrusion multiplier but still had this stringy stuff all over it. This one is with extrusion multiplier set to 0.96. My temp is currently set to 215C using Printrbot White Filament.
-
—
—
Has anyone tried the AZSMZ Mini? I just saw it on ebay and aliexpress and was curious
Has anyone tried the AZSMZ Mini? I just saw it on ebay and aliexpress and was curious http://www.aliexpress.com/item/32-bit-ARM-based-Motion-controller-for-3D-printers-CNC-Machines-and-Laser-cutters-Like-Azteeg/32257951240.html
-
—
—
What's a good webcam for monitoring your print job?
What’s a good webcam for monitoring your print job? I’m thinking the Logitech HD Pro C920 but I don’t know if it would work or if there is a better option.
-
—
—
have any of you considered using a tablet with usb for the printer
have any of you considered using a tablet with usb for the printer. i have tried it and it works fine, and there is a lot of opportunities.
-
—
—
I not being careful when trying to figure out an LCD and crossed some pins on my smoothieboard v1.0a with a multimeter probe and saw some smoke
I not being careful when trying to figure out an LCD and crossed some pins on my smoothieboard v1.0a with a multimeter probe and saw some smoke. I should know better.
-
—
—
Just turned some lead screws and bored some pulleys today;
Just turned some lead screws and bored some pulleys today; Z axis is coming together for my Ingentis Variant, the stepUP 😀
-
—
—
I've been getting some excess filament when printing
I’ve been getting some excess filament when printing. About 5 hours into printing the gauntlet it got caught up and shifted the entire print over 1/4 inch. :(
-
—
—
I want say hi to all ...
I want say hi to all … its my first post into this community. You are doing a great work here and very valuable information. There is one question I can’t fully answer in my head due to my limited mechanical knowledge. I see for XY carriage motors they get connected to driving rods using a small close loop belt. What are the reason behind this? Why they are not connected directly at the end of the rod using a motor coupling? To make it more compact or to reduce the stress on motor axis due to push back forces during accelerating/decelerating? Sorry if this had been answered before.
-
—
—
15 hour print job for the Gauntlet part of this Raptor Hand by e-NABLE scaled up to 170%
-
—
—
new to this group since today, I would like to raise some questions
new to this group since today, I would like to raise some questions. RUnning rather happily my self build Prusa I3, it’s time to consider a next step in building 3D printers. Eustathios seems the way to go because of size, the extruded frame foundation (living in Holland, sourcing from Germany is doable) and an active community. Having read the documentation I could find I wondering what kind of stepper motors are required (not mentioned in BOM). I presume it’s NEMA17 but considering size of the printer I imagine a minimum torque is required. Next to that when it comes to printed parts, what material has delivered the best results. Candidates that come into my mind are PLA (not sure for parts close to hot end), ABS (toxic in printing), PETG (no experience yet but according to various reports it should be easy in printing and extremely strong).
-
—
—
after i posted last night i realised that my setup is 3mm and most people here are running 1.75, so i figured i might as well see if something similar could be done
after i posted last night i realised that my setup is 3mm and most people here are running 1.75, so i figured i might as well see if something similar could be done. it works… i center drilled a 4mm bolt, heated the end of the tube, and screwed it in. its not perfect, as my bit angled a bit while drilling. ideally i would probably machine an aluminum adapter and thread the tube onto that, but for proof of concept it worked pretty well.
-
—
—
Thought I'd share my solution to keeping my bowden tube connected on my ultimaker, as I've seen a few posts about bowden tube nuts here
Thought I’d share my solution to keeping my bowden tube connected on my ultimaker, as I’ve seen a few posts about bowden tube nuts here. Instead of threading the outside, I heated up the end of my bowden tube,shoved it over a pair of needle nose pliers to expand it, then threaded it over the top of a threaded PEEK tube I machined to replace all the push fittings and clips in the hotend assembly. I’ve been running it this way for the past 2+ years and it hasn’t come off once. Just thought it might help someone else keep their bowden in place.
-
—
—
I always forget how quiet parts of these printers are before the fans are installed
I always forget how quiet parts of these printers are before the fans are installed. #Ingentilere
-
—
—
Time for another edition of "Erik's Stupid Question of the Week!"
Time for another edition of “Erik’s Stupid Question of the Week!”
-
—
—
Hmm. It's a mini tugboat? (The green one if for reference from another printer) I haven't done the PID thing but would that cause this on my Eustathios Spider V2?
Hmm. It’s a mini tugboat? (The green one if for reference from another printer)
-
—
—
good afternoon, forgive my English which is actually that of Google, since I do not master your language
good afternoon, forgive my English which is actually that of Google, since I do not master your language. Just to thank you for your work, which I used to fabricarme a new 3d printer. I miss some modifications to use diameter 10 and already becomes limited.
-
—
—
Hey Guys, Any Ideas what would be causing this?
Hey Guys, Any Ideas what would be causing this? Model appears fine in S3D preview and then when it is sliced….looks like this.
-
—
—
I'm having trouble keeping the filament in the bowden tub nut trap
I’m having trouble keeping the filament in the bowden tub nut trap. Is the tubing supposed to just push in there?
-
—
—
SeeMeCNC Probe: Just wow. Nice idea to remove some weight but still have a sensor
SeeMeCNC Probe:
-
—
—
trying to get into contact with the Herculean crew....
trying to get into contact with the Herculean crew…. about testing 3D EeZ
-
—
—
Is it critical that the aluminum plate be perfectly flat?
Is it critical that the aluminum plate be perfectly flat? I didn’t check that it was flat upon receiving but after it was cut on the water jet I noticed that it has a slight bend in it.
-
—
—
Can any of the Bondtech-Extruder users (e.g
Can any of the Bondtech-Extruder users (e.g. +Eric Lien) or +Martin Bondéus say something about the acceleration and e jerk they’re using or think is best? Also i’d be glad to get some tips for setting the screws on the bondtech to a right value. So far i completely screwed them out and while feeding some filament in slowly screwed them in while giving some pulling force to the filament to see how good the transport force is.
-
—
—
Just echoing some thoughts: I'm just looking at buying the linear shafts (smooth rods) for the Eusthios spider v2, and it occurs to me that, unless I am mistaken, you could simply remove 3 of the top shafts and this printer
Just echoing some thoughts: I’m just looking at buying the linear shafts (smooth rods) for the Eusthios spider v2, and it occurs to me that, unless I am mistaken, you could simply remove 3 of the top shafts and this printer would function as an H-bot. So there must be some advantage to using 3 extra shafts- I’m guessing that it helps stability and accuracy. Another thing I am somewhat wondering is if everything could be done in 8m diameter shafts- it’s not that big of a printer (around 500mm).
-
—
—
For the heating pad I see Eric changed from 500W for the Eustathios Spider 2 to 800W for the Herculien
For the heating pad I see Eric changed from 500W for the Eustathios Spider 2 to 800W for the Herculien. What is the best wattage heating pad at 120V that people have found? As far as I know Marlin firmware just passes the full voltage (unpulsed) to the heating pad. Sivia at Alirubber said a 120V pad has a resistance of 20ohm, so 120/20=6A 120Vx6A=720W.
-
—
—
Does anyone have a dxf of the MDF insulator board, or the measurements of the two levels of the cuts?
Does anyone have a dxf of the MDF insulator board, or the measurements of the two levels of the cuts? I cannot seem to get edrawings installed my my pc, and am ready (finally) to cut this out. I received my aluminum plate yesterday, so am almost complete on this build, after a bit of a delay.
-
—
—
Made a quick mount for a cable chain to carry the heated bed wires
Made a quick mount for a cable chain to carry the heated bed wires. It would make the printer look nicer and cleaner, but I am a bit worried this may put some forces on the bed that may be undesirable and affect print quality. The chain will ride on the left-rear vertical extrusion. I couldn’t make this work in the CAD assembly, unfortunately, but it will in real life. Thoughts?
-
—
—
Got some LED Lights hooked up to my Azteeg X3 board on pin 11 and added button switches on Pronterface with the m42 p11 s255 for 'on' and m42 p11 s0 for 'off'
Got some LED Lights hooked up to my Azteeg X3 board on pin 11 and added button switches on Pronterface with the m42 p11 s255 for ‘on’ and m42 p11 s0 for ‘off’. Also got my Eustathios V4 Carriage mounted, Not an easy swap, practically had to disassemble the entire gantry. Other than that it is back to printing. The only negative thing with the new carriage is that I cannot clear unexpected plastic ooze from the hot end while it begins to print because the fan housing is very much in the way.
-
—
—
We were discussing electronics cooling in another post here in the community and I volunteered to whip up a simple cooling duct to direct the air from the 40mm fan onto the printer board
We were discussing electronics cooling in another post here in the community and I volunteered to whip up a simple cooling duct to direct the air from the 40mm fan onto the printer board.
-
—
—
As i seem to have fixed my biggest problem which was caused by retraction length there appears to be one that is totally filament related
As i seem to have fixed my biggest problem which was caused by retraction length there appears to be one that is totally filament related. The Filament is eSun PETG (transparent blue). That stuff basically prints quite well as long as the layer or “island” is big enough. I’m only using 2,5mm retraction in this print and you can easily spot the problem. It appears in the small posts of 3DBenchys house and on the chimney. Not only that extrusion is totally unreliable it also seems to overextruder after a short while. I’m not sure where this may come from and havent seen this before. I’ve double checked the filament transport in the Feeder and that doesn’t show any problems.
-
—
—
Is there any problem if I solder standard 12 gauge wire to extend the heater cartridge wires off the hot end?
Is there any problem if I solder standard 12 gauge wire to extend the heater cartridge wires off the hot end?
-
—
—
At the end of the day it's a bit frustrating...
At the end of the day it’s a bit frustrating… well maybe more than a bit. But: I’m getting closer to the cause. The PETG first printed well in continues extrusion (that vase i posted) but then it failed again with the smaller nozzle while printing the little Marvin. This brought me to investigate a bit more in combination with retraction. I changed filaments as i didn’t trust the PETG to a cheap PLA that i already have for quite a while. It wasn’t that complicated to print so far though i hadn’t printed it for quite some while.
-
—
—
This person Gus Montoya built a similar printer ( ) but it uses all linear bearings
This person Gus Montoya built a similar printer (https://plus.google.com/u/0/107253148599893854804/posts/4REdLTz36HD?cfem=1) but it uses all linear bearings. Are there any advantages to using the bushings linear+rotation design versus just the linear design?
-
—
—
Vase anyone? :-) At least the continous extrusion seems to work well now
Vase anyone? :-) At least the continous extrusion seems to work well now. I’ve selected a print that works without much retracts and printed that vase with the 0.6 nozzle and 0.4 layer height quite well. I’ve changed the bowden tube to a longer one (950mm is really massively long, +Eric Lien - sure we need that much of an arc?) and found a carbon stick to support it - that works ok for the moment.
-
—
—
A few Eustathios Spider V2 questions.... What are you wiring the 24V fan that cools the equipment to?
A few Eustathios Spider V2 questions….
-
—
—
Does anyone have a good comparison for controller boards;
Does anyone have a good comparison for controller boards; Panucatt vs. Smoothieboard vs. RAMPS (those seem to be the main 3)? I have just about everything mechanical good to go, just don’t have a controller board picked out yet. I’m anxious to start seeing some things move around.
-
—
—
Time to get the level out... So I checked the base for level and it is with a little adjustment
Time to get the level out… So I checked the base for level and it is with a little adjustment. So from there I made the bed level. When I place the level on the smooth rods, they are not exactly level. Is this normal?
-
—
—
Guys, i'm a bit stuck with my Extrusion and hope to find some help
Guys, i’m a bit stuck with my Extrusion and hope to find some help. I’m using a Bondtech Extruder on my Eusthatios (Bowden setup, around 80mm bowden tube currently, already had it shorter and a bit longer too) and en E3Dv6 of course. Bascially stuff works quite well with ABS and Colorfabb PLA. I also don’t have big problems with some other cheaper PLA i had around.
-
—
—
Has anyone yet thought abour replacing that noisy E3D fan with something more efficent and less noisy?
Has anyone yet thought abour replacing that noisy E3D fan with something more efficent and less noisy? As my printer is rather silent now the main noise comes from my 50mm board cooler (which is my fault, will replace this with at least 60 or even 80mm) and the 30mm E3D blower. I’m thinking about using a second 50mm blower like on the duct to cool the Hotend. That ones are really silently spinning. What do you think? Maybe i’ll just play around a bit with a redraw of the carriage.
-
—
—
Robotdigg now have 8mm drive gear for just $2.10
Robotdigg now have 8mm drive gear for just $2.10.
-
—
—
How do you guys with Bondtech V2, Bowden and E3D have you Retraction set?
How do you guys with Bondtech V2, Bowden and E3D have you Retraction set? Basically retraction works but i see a late extrusion after retracts from time to time and i’m completely stuck where this comes from. Maybe the bondetch force isn’t set right with the screws yet.
-
—
—
Hi Folks, Finalizing my Herculien build, hopefully today I can get the clear covers mounted
Hi Folks, Finalizing my Herculien build, hopefully today I can get the clear covers mounted. Here is the Azteeg X3 box, front Viki 2 mount on my Herculien. Printing now using a nylon version of the spool holder. Nylon is so nice and strong, I kept breaking them with PLA and ABS prints. I could not find the 12 mm and 25 mm holder so I modified the 50mm version and uploaded them to youmagine.com. As you can see my Bondtech is pulling hard on that spool netting and no signs of giving up. I think I may have to make another printer part so it can replace that blue tape. Also I am redoing the power receptacle since the power supply will be mounted outside the box since I have opted not to cut any of the acrylic covers.
-
—
—
So with almost two feet of Z, Eric recommended a fixed point for the threaed rod
So with almost two feet of Z, Eric recommended a fixed point for the threaed rod. Had to stop at Familab and get lessons on using a lathe to turn down the threads.
-
—
—
Can someone explain how I need to hook up the wiring and filament tubing?
Can someone explain how I need to hook up the wiring and filament tubing? I have this 8 position connector that goes in the mix somewhere. Do I terminate all my wiring from the extruder to it and then run the jumper wire down to the bottom and send those wires where they need to go.
-
—
—
E3D V6 Assembly Are these the same?
E3D V6 Assembly
-
—
—
After months of a slow build (due to limited funds) I finally got my Herculien build moving last night and had some unexpected issues
After months of a slow build (due to limited funds) I finally got my Herculien build moving last night and had some unexpected issues. I had relatively smooth movement in both X and Y when I realized I had installed the carriage backwards (I’m using the Eustathious Spider carriage with the cooling duct - v4). When I reinstalled the carriage the correct direction the X axis of the carriage now has a lot of resistance to motion. I tried spinning the rod with a drill (for about 15 minutes) which helped very slightly, but it is not nearly as smooth as the Y axis motion. I have smooth motion everywhere in the gantry, other than along the X axis of the carriage. The cross-rod running the Y direction is visibly flexing when manually performing an X-axis move…
-
—
—
Would some one be able to post the steps per mm for the Herculien?
Would some one be able to post the steps per mm for the Herculien? Also if anyone has the acceleration figured out it would be a great help and it would save me a lot of time. Hopefully I will be printing on Sunday or Monday if everything goes well.
-
—
—
Running at 150%. Oh come on! See anything wrong with carriage?
Running at 150%.
-
—
—
I'm moving slow and steady on the build
I’m moving slow and steady on the build. Sometimes I feel like I take one step forward and end up three steps back. This is definitely the most complex time consuming rep rap I’ve built. Could someone also post pictures of the carriage fully assembled with hotends?
-
—
—
Got past the belt grinding noise and the vibrating....
Got past the belt grinding noise and the vibrating…. Does this look like it’s working well?
-
—
—
Would anyone be able to post photos of how the endstops are mounted on the Herculien?
Would anyone be able to post photos of how the endstops are mounted on the Herculien?
-
—
—
Once I set the microstepping to 1/32 instead of 1/2 (oops) I was able to run the break in g code
Once I set the microstepping to 1/32 instead of 1/2 (oops) I was able to run the break in g code. I’m having trouble though.
-
—
—
The push-fit connectors used for connecting the Bowden tube to the extruder gives a bit play of the bowden tube, this decreases the effective amount of retraction
The push-fit connectors used for connecting the Bowden tube to the extruder gives a bit play of the bowden tube, this decreases the effective amount of retraction. In order to counteract this there are two solutions.
-
—
—
Well, Good news that I was able to print some parts, bad thing is that my extruder gave up on me so I will have to wait for my turn in print forward(((
Well, Good news that I was able to print some parts, bad thing is that my extruder gave up on me so I will have to wait for my turn in print forward(((. I ordered every part from the BOM except ballscrews so now it is just a matter of waiting.
-
—
—
Got to do some test fitting today, everything went together quite nicely
Got to do some test fitting today, everything went together quite nicely. This thing is a freakin tank! Can’t build the gantry until I get those ball screws trimmed up. Screwed up and ordered 500mm instead of 450mm.
-
—
—
I am new here and got my first 3D printer a few months ago (Robo3D) I decided I am going to build a HercuLein because of the dual extruders
I am new here and got my first 3D printer a few months ago (Robo3D) I decided I am going to build a HercuLein because of the dual extruders. It will be a very slow build, so everyone that says their build is slow will be surprised at just how fast they put their together compared to mine. I am in the process of printing out the printable parts and see that there are a few that I can’t find in the pictures. I am wondering if every STL needs to be printed. I am actually printing two sets while I am perfecting my Slic3r profiles for the Robo. The first set is about 1/5 of the way through in ABS, the second set will be in PETG. PETG is my preferred filament, but I need the practice in ABS.
-
—
—
I wonder what your performance Data is for the Eusthatios Spider V2?
I wonder what your performance Data is for the Eusthatios Spider V2? What acceleration values are you using on X and Y and what are your usual printing speeds?
-
—
—
Testing big
Testing big.
-
—
—
Test fit for the frame of the Ingentis Variant that I'm working on, the stepUP, made of hand-milled aluminum extrusion;
Test fit for the frame of the Ingentis Variant that I’m working on, the stepUP, made of hand-milled aluminum extrusion; still have to find one last extrusion for the top which I misplaced and get some more work done on the rest of the machine
-
—
—
Eustathios Spider V2 break in gcode.... Where do I set the bed dimensions?
Eustathios Spider V2 break in gcode…. Where do I set the bed dimensions? Is this in Octopi or in the smoothie config file or both?
-
—
—
At the request of Igor Kolesnik we would like to know what electronics you are using on your Ingentis / Eustathios / HercuLien style printers
At the request of +Igor Kolesnik we would like to know what electronics you are using on your Ingentis / Eustathios / HercuLien style printers. I personally go with Panucatt Devices controllers like the Azteeg X3, and X5 Mini because my personal belief is Roy makes the best quality boards out there. But then again I have not tried everything, and peoples mileage may vary from my own.
-
—
—
Update: after switching from the Walter Hsiao -Version of the XY belt tensioners to the Eric Lien default ones my mechanical problem is completely gone
Update: after switching from the +Walter Hsiao-Version of the XY belt tensioners to the +Eric Lien default ones my mechanical problem is completely gone. Printer runs again. \o/
-
—
—
I have doubt on the eustathios BOM..
I have doubt on the eustathios BOM.. there is this item from SMW3D or openbuilds called Precision Ball Bearing … What are the specs of these bearings?
-
—
—
Does anyone have a link or Google Doc for the Eustathios Spyder 2 BOM?
Does anyone have a link or Google Doc for the Eustathios Spyder 2 BOM? I cant get the one in the Github to open.
-
—
—
A mount to fit the Bondtech Extruder to the Herculien-frame, c-c distance is 60 mm to fit on the top 20x80 extrusion
A mount to fit the Bondtech Extruder to the Herculien-frame, c-c distance is 60 mm to fit on the top 20x80 extrusion. Use 35 mm long M5 bolts and M5 T-slot nuts.
-
—
—
First print. Some imperfections are still there but nothing that can't be fixed
First print. Some imperfections are still there but nothing that can’t be fixed. Red PLA. Dimentions are spot on. Today I’m going to try printing a new extruder
-
—
—
Eric Lien i will try to print a modified version of your XY Belt Tensioners instead of the ones from Walter Hsiao as i have difficulties getting belt tensioning done reliably with the Flex inserts
+Eric Lien i will try to print a modified version of your XY Belt Tensioners instead of the ones from +Walter Hsiao as i have difficulties getting belt tensioning done reliably with the Flex inserts. I wonder how you suggest to print yours? Generally i would think it would be good to orient them like in the screenshot but how about that belt teeth inside the slots? They probable would mess up this way? Print everything with support and turn them around so the teeth are facing up doesn’t sound great either.
-
—
—
When clicking on Z Home my print bed goes down instead of up to the Z endstop
When clicking on Z Home my print bed goes down instead of up to the Z endstop. Is this a setting in the Azteeg X5 Mini config?
-
—
—
I finally got my X and y axis moving on my Herculien but i am now having problems with binding on the z axis
I finally got my X and y axis moving on my Herculien but i am now having problems with binding on the z axis. It just seems tight and he belts are skipping. I hope someone has insight.
-
—
—
Hey guys, unfortunately things came out quite worse then expected on first sight
Hey guys,
-
—
—
Hardware is coming together, forgot to put on pulleys so the lead screws have to come back out
Hardware is coming together, forgot to put on pulleys so the lead screws have to come back out.
-
—
—
I can't for the life of me find the correct heater mat for the Eustathios
I can’t for the life of me find the correct heater mat for the Eustathios. The closest I could find is this: http://www.aliexpress.com/item/Custom-Silicone-Hot-Bed-For-3D-Printer-320x320MM/32319957576.html but It doesn’t seem to have the thermistors. Anyone mind pointing me in the right direction?
-
—
—
Looks like we have a running printer :-)
Looks like we have a running printer :-)
-
—
—
Has anyone done any form of auto leveling on the herculien with smoothie board?
Has anyone done any form of auto leveling on the herculien with smoothie board? I have auto level on the printrbot and although not needed it is sometimes nice. The printrbot was limited to three points due to the printer board and I was wondering if with smoothie you could do like a 9 point level?
-
—
—
I just received my ball screws for my Z-axis from Aliexpress
I just received my ball screws for my Z-axis from Aliexpress. Has anyone else used these? Can you flip the ball nut around the other direction on the screw, or will I end up with a mess of ball bearings when I take it off? They are not facing the right direction..
-
—
—
In big printer news: E3D Kickstarts a big printer!
In big printer news:
-
—
—
Eric Lien , On the Spider V2 Z-axis Leadscrew supports, what is the purpose of the diaphragms in the holes?
+Eric Lien , On the Spider V2 Z-axis Leadscrew supports, what is the purpose of the diaphragms in the holes? Just curious before I print them, wondering if i’ll need support material or anything.
-
—
—
Eric Lien I have some suggestions for the Herculien BOM you might consider
+Eric Lien I have some suggestions for the Herculien BOM you might consider. I don’t believe the M4 screws used to attach the 24V power supply are included in the BOM, it may be helpful to add those. Also, I was looking for alternative shims for the pulleys and came across these:
-
—
—
I have octopi running on my raspberry pi
I have octopi running on my raspberry pi. Is there anything I need to do to the Azteeg X5 Mini before it will allow me to move the Z stepper motor?
-
—
—
I made some modification to the Viki2 (Eustathios) mount to be used on my Herculien
I made some modification to the Viki2 (Eustathios) mount to be used on my Herculien. It is not printing pretty yet as I am still learning how to dial in my printer settings and also creating a 3D drawing that is acceptable to a 3D printer format is another challenge. My next attempt is to print my new drawing of an Azteeg X3 box. I cant wait for my Bontech extruder to arrive as I know I am probably printing too fast on the stock extruder. Printing to me is like watching grass grow but the things you pull from the build plate is a gift!
-
—
—
How do you guys tune your axis positions and movement of X and Y axis when building your printer?
How do you guys tune your axis positions and movement of X and Y axis when building your printer? I just wonder as i want to make sure X/Y movement is as good as possible before starting to give it a go with the motors? For now i think it’s a bit strong to move by hand but i don’t have a real comparison. I’ve built a classic Ultimaker some 2 years ago and think it was about the same back then, but well… i thought i could improve it a bit possibly.
-
—
—
I got everything electrical mounted. What size wiring should I use?
I got everything electrical mounted. What size wiring should I use? Is there a picture or diagram with everything hooked up that I can use for reference?
-
—
—
I don't know what happened, but I accidentally doubled up on stepper motors and 300x300mm silicone heater pads (24V) from Robotdigg
I don’t know what happened, but I accidentally doubled up on stepper motors and 300x300mm silicone heater pads (24V) from Robotdigg. I just completed the order when I realized my mistake, so they are on the way. Let me know if you are interested.
-
—
—
Here's another view from the (incomplete) bottom
Here’s another view from the (incomplete) bottom.
-
—
—
I've got some new pics from our build session last night
I’ve got some new pics from our build session last night. We’re getting close. Some cabling works to do and still some things to find out. I still don’t know how i wanted to mount the Bondtech extruder. The printable V-Mount that +Martin Bondéus offers to print works well but mounted at the right front corner would make the motor point to the front which is ugly and impractible here. Maybe i have to draw myself a custom mount.
-
—
—
Starting to look like an awesome 3D printer
Starting to look like an awesome 3D printer. I think I spent most of the day tearing the frame apart to get the remaining T-Nuts in for the Plexiglas to attach to the frame.
-
—
—
Fresh off my school's CNC router: my print bed and bed mount
Fresh off my school’s CNC router: my print bed and bed mount. Now I wait for the rest of the parts to arrive in the mail.
-
—
—
hey.. been following this forum and i have seen a lot of build logs and improvements etc ...
hey..
-
—
—
For a Monday, I've got a lot done today!
For a Monday, I’ve got a lot done today!
-
—
—
What exactly am I looking for, spec-wise, when it comes to the precision linear rod?
What exactly am I looking for, spec-wise, when it comes to the precision linear rod? I’ve already ordered 8mm precision chrome rod from Folgertech.com, but they do not have 10mm chrome rod. What they do have is “10mm smooth Drill Rod - O1 Grade”. How do either of these compare to the 52100 steel rod from Misumi that is specified in the BOM? Will those suffice, or am I safer just biting the bullet and spending a little more to get the rods from Misumi? The 10mm rod from SMW3D appears to be O1 grade also, so I assume O1 steel rod is sufficient to use? They have been sold out for a couple weeks, however..
-
—
—
I'm so close to finishing, I can already feel the bed heat!
I’m so close to finishing, I can already feel the bed heat! But I’m having some issues that I need to resolve before continuing. These issues seem to be firmware related, at least I think so.
-
—
—
How easy should these slide back and forth?
How easy should these slide back and forth? I’m concerned that it isn’t sliding easy enough. I can slide it with one finger fairly easy, but it definitely doesn’t slide as easy as the carriage bearings do. (I will have to confess here, that when I first put the bearings in, I pressed them in gently with the vise) So I’m trying to decide if I need to purchase new ones. I did pop them out and sand the PLA piece to make them fit easier. Should I order new bearings or just go with it? One more question? Why don’t we use the LM10UU type bearings here? They seem like they would work a lot better!!
-
—
—
Hmm i just wondered if the molex pins will be good for the extruder!?
Hmm i just wondered if the molex pins will be good for the extruder!? We’ve got 8 pins so there’s no chance of doubling them for the extruder. I couldn’t find any specifications that tell - just anything else but nothing about current max.
-
—
—
Well hello everyone, I feel as though it's time come out of the woodwork
Well hello everyone, I feel as though it’s time come out of the woodwork. I’ve been lurking for quite some time following everyone’s build while I myself gathered the parts for my own build. Now that I’m finally nearing the completion of my printer, I’m looking forward to interacting with the community while printing out some functional projects once it’s done.
-
—
—
I just saw the price at MCMasters for all screws and washers
I just saw the price at MCMasters for all screws and washers. Gave me a thought. Since most of parts are coming in x100 I can resell leftovers by their price + shipping to whoever will be interested. parts will be sorted and marked by eustathios v2 BOM
-
—
—
I wasn't able to find the shims in my town and I remembered I had this filament from Igus
I wasn’t able to find the shims in my town and I remembered I had this filament from Igus. It prints pretty easy and moves super smooth on the rods.
-
—
—
would someone be able to give me info on assembling the hercustruder?
would someone be able to give me info on assembling the hercustruder? I was not able to find info on assembly on the build guide. The end is nearly in sight.
-
—
—
Coming together and hit yet another snag
Coming together and hit yet another snag. Everything was sliding very smoothly individually but after assembly its rather snug. Obviously its alignment somewhere.
-
—
—
Eric Lien Now what? How can I fix this situation?
+Eric Lien Now what? How can I fix this situation?
-
—
—
Trying again, cross-posting from reddit
Trying again, cross-posting from reddit.
-
—
—
Hey everyone! I've been lurking around this community for a while gathering some design ideas and inspiration as I've been working on my own variation of the Eustathios
Hey everyone! I’ve been lurking around this community for a while gathering some design ideas and inspiration as I’ve been working on my own variation of the Eustathios. And here it is!
-
—
—
I am completely stuck at this moment
I am completely stuck at this moment. My friend who was going to print parts, moved to another country so my project is delayed for unknown period of time.
-
—
—
Thanks Gus Montoya for posting those pictures of your progress!
Thanks +Gus Montoya for posting those pictures of your progress! It finally got me motivated to put my Eustathios Spider V2 together. Can’t wait to work on this some more tomorrow. :)
-
—
—
Is there another good source for the 8mm and 10mm sintered bronze press-fit bearings?
Is there another good source for the 8mm and 10mm sintered bronze press-fit bearings? Or maybe a good alternative? I’m having a tough time finding anywhere with both 8mm and 10mm in stock. Plus, SDP/SI’s shipping and handling charge for 8 10mm bearings is $17. I’d really like to avoid spending $80 on 12 bearings if possible…
-
—
—
Originally shared by Rick Sollie Got the frame finished but I think I made a mistake somewhere
Originally shared by Rick Sollie
-
—
—
So the smoothie board is not mounted to the plastic 3d printed part, it's mounted to the plastic sheet of the printer?
So the smoothie board is not mounted to the plastic 3d printed part, it’s mounted to the plastic sheet of the printer? Same with power supply? Could someone share their electronic mount?
-
—
—
Hi people. I am new to this community but I've been following it for a while
Hi people. I am new to this community but I’ve been following it for a while. I am getting to the first print stage so I decided to share what I’ve built so far.
-
—
—
Z-stage installed. What's not obvious about this printer's design is the reuse of other parts
Z-stage installed. #ingentilere What’s not obvious about this printer’s design is the reuse of other parts. It’s using the motor mounts and carriage from +Eric Lien, and the Rod holders are designed to use his motor mount for the Z-stage.
-
—
—
I have problem. when im printing its like the layer is getting to high, that so my nozzle hits the last layer when travel
I have problem. when im printing its like the layer is getting to high, that so my nozzle hits the last layer when travel. Does any one know what is causing this?
-
—
—
Finally happy with this print quality! After gluing my bowden adapter ring back into its housing and tweaking my bowden path a little, and also reducing my retract speed (3600mm/min is too much even for the might bondtech!)
Finally happy with this print quality!
-
—
—
Finished for the night. Tomorrow I finish aligning everything
Finished for the night. Tomorrow I finish aligning everything.
-
—
—
I've been messing with this fully enclosed, direct drive, plywood version for a while (OnShape access on request)
I’ve been messing with this fully enclosed, direct drive, plywood version for a while (OnShape access on request).
-
—
—
In search of opinions for a board
In search of opinions for a board. I followed the HercuLien BOM and went with a Azteeg X3 V2 but I ended up receiving a bad board. It’s been weeks that I’ve been trying to get any replies from Panucatt for a replacement but it seems they don’t believe in customer service.
-
—
—
After having ordered parts and getting parts printed here and there, I'm finally assembling
After having ordered parts and getting parts printed here and there, I’m finally assembling. Have the handycam running so hopefully I will have a timelapse of the entire build.
-
—
—
Been busy trying to get the Herculien parts online and ready to place the order ...
Been busy trying to get the Herculien parts online and ready to place the order … but i came across this doubt on these items :
-
—
—
Just wanted to leave a short update on our build
Just wanted to leave a short update on our build. Finally got something done yesterday. The x/y carriage still needs some work as the bushings (Robotdigg graphite bushings) don’t align well yet. Need to reprint the carriage with higher quality and be a bit creative with the accessories (sleeves and stuff).
-
—
—
How do people remove the filament from the hotend at the end of a print or to change over?
How do people remove the filament from the hotend at the end of a print or to change over? Just a fast retract while hot?
-
—
—
Welp, I"m going to have to throw in the towel and sell all my parts unfortunately (life/work happened)
Welp, I”m going to have to throw in the towel and sell all my parts unfortunately (life/work happened). I ended up purchasing all the best parts I could get (wanted the best FDM printer I could get).
-
—
—
Does anyone of the European/German guys have a source for the self aligning bronze bushings?
Does anyone of the European/German guys have a source for the self aligning bronze bushings? I couldn’t find them here so far - only overseas sellers.
-
—
—
Hey all, Another weekend, another day of tweaking
Hey all,
-
—
—
What lubrication did everyone use on their linear rods?
What lubrication did everyone use on their linear rods?
-
—
—
So I got a chance to sit down with Jon Hirschtick (founder of Solidworks and OnShape) and his wife during their stopover in Iceland
So I got a chance to sit down with Jon Hirschtick (founder of Solidworks and OnShape) and his wife during their stopover in Iceland. Discussing my Herculien variant (which is the biggest project (not the most complicate one though) in Onshape atm :p) , 3d printing in general and OnShape. +Eric Lien He knows about you now :)
-
—
—
Most of the parts for my large scale printer came in
Most of the parts for my large scale printer came in. Just waiting on a few more and will start building it soon.
-
—
—
Hi! Am going to have some free time in a couple of weeks and am planning on building another printer (I already built a smartrap and a rostock)
Hi! Am going to have some free time in a couple of weeks and am planning on building another printer (I already built a smartrap and a rostock). I would like it to have 250 mmˆ3 square mm printing volume.The type of printer would be some similar to the ones you have, but would like to have the motors inside (to close it with wood panels) and also without closed belts (instead a closed+open belts, I am going to use only a open one, like Prusa and delta). Also, the Z motor will have an industrial screw atached with a flexible coupling (instead of the belt and the threaded rod). Have you tried it before? Which model do you think could fit those needings? Does all of them use 10 mm rod? I will use 8 mm rod in the square perimeter (guides) and 6 mm rod in the cross.
-
—
—
Has anyone yet done an Eustathios build with the motors on the inside?
Has anyone yet done an Eustathios build with the motors on the inside? Just thinking about a smaller version that fits well on my desk and is portable as well. Therefore i’d better not have any parts hangin on the outside. I’d be keen to see the ideas how to do an inside mount the best way. Like Ultimaker does it? Probably any better ideas for aluminum extrusion frames? Still not sure if i will go with extrusion on the smaller one.
-
—
—
Man Walter Hsiao is so good! I think I am going to have to try this out
Man +Walter Hsiao is so good! I think I am going to have to try this out. I have been wanting to try ninjaflex for a while.
-
—
—
Made some modifications to my Ingentis Variant, the stepUP (see ) Wanted to use some proper linear ball bearings for precision, alignment, and machinability reasons instead of the sintered bronze bushings that are typically
Made some modifications to my Ingentis Variant, the stepUP (see https://plus.google.com/113675942849856761371/posts/fPm4NqVuJzZ)
-
—
—
Alpha release Z-stage. Scrap rod, leadscrew not yet cut to length, could be duplicated on the other side if the bed got larger than wise for a cantilevered bed
Alpha release Z-stage. Scrap rod, leadscrew not yet cut to length, could be duplicated on the other side if the bed got larger than wise for a cantilevered bed. The built plate will be on 3 points for easy tram adjustment.
-
—
—
Where do I go from here? Do these screws need a washer under them or just tighten them down the way they are?
Where do I go from here? Do these screws need a washer under them or just tighten them down the way they are? Also what do I need the shims for?
-
—
—
First movements
First movements
-
—
—
One step closer. I now need to source the aluminum angle L, the aluminum bed and the mdf pocket
One step closer. I now need to source the aluminum angle L, the aluminum bed and the mdf pocket. I have been putting off on these since I have had the time to call around town for a metal shop that has them.
-
—
—
My first usable part on the printer
My first usable part on the printer. I did not get a chance to modify the V2 spider Viki2 mount but I will eventually adjust it to fit the Herculien.
-
—
—
I have a lot to learn with printing, not at all pretty yet but slowly getting there
I have a lot to learn with printing, not at all pretty yet but slowly getting there. Yup, definitely need to slow printing down, I believe I have some imperfections on some parts, it could be the bearing mounts for the rods a bit loose, bearing just fall off when assembling the gantry and I can rattle it a bit, will shoe goop the bearings in so there is no play. On this video of the Iphone amp stand , I can see I have quite a bit of miss extrusions and a fair bit of spider webbing. I will try .03 layer instead of .5 and maybe some extrude retract setting.
-
—
—
Considering my options I bite the bullet and bought a sheet of 1/8" thick 5052 aluminum
Considering my options I bite the bullet and bought a sheet of 1/8” thick 5052 aluminum. I think it’s enough to cut out 3 build plates with some material to spare. Anyone needing a build plate for their Eustathios V2? After I have them cut I’ll post pic’s and I’ll also have a price.
-
—
—
One last question (hopefully). When using the Alignment tool for the eustathios V2, does the alignment tool bolt on to the frame or?
One last question (hopefully). When using the Alignment tool for the eustathios V2, does the alignment tool bolt on to the frame or? Does anyone have picture’s of their proper use?
-
—
—
Beautiful work as always by Walter Hsiao
Beautiful work as always by +Walter Hsiao
-
—
—
Just looking at buying parts through AliExpress
Just looking at buying parts through AliExpress. Would this be a bad choice or has a bunch of others had no problem? Any feedback would be awesome before I order some stuff.
-
—
—
Am I just half asleep or their isn't a wiring diagram for the smoothieboard?
Am I just half asleep or their isn’t a wiring diagram for the smoothieboard? Any one have pic’s?
-
—
—
Introducing (Italian: to refine, civilize) What started as a project where I had a pile of spare parts turned into a thought experiment where it seemed like the Ingentus, HercuLien, Eustathios printers while excellent for
Introducing #ingentilire (Italian: to refine, civilize)
-
—
—
I could not wait any longer for the bed heater to arrive so my son and I wanted to see how it would print ....
I could not wait any longer for the bed heater to arrive so my son and I wanted to see how it would print …. after reassembly the Z-gantry and build plate (lot easier with help) we tried a test print of a square with a cylinder. We warmed up the build plate with a heat gun and after screwing up all the settings in Slic3r settings in Pronterface we finally see a recognizable object. I wonder if there is a noob setting for all the variables we have?
-
—
—
Finally got around to finalizing my printer design
Finally got around to finalizing my printer design. Time to order some parts.
-
—
—
Oh yeah. My first personal shop machine purchase is putting into used
Oh yeah. My first personal shop machine purchase is putting into used. These holes are cleanly made.
-
—
—
Wow, this black PETG from ESUN is great to print with
Wow, this black PETG from ESUN is great to print with. A few rolls showed up on Amazon and I snatched them up. Looks like its back in stock on June 20th.
-
—
—
Got this today for the Spider V2 build
Got this today for the Spider V2 build. I got so excited when I saw the dimensions!!!
-
—
—
leave a comment
leave a comment
-
—
—
Got it running have made 3 prints
Got it running have made 3 prints. I think the result is pretty good.
-
—
—
First Moves for my HercuLien! Connected smoothieboard up, installed pronterface, and a power supply and Boom, operational!
First Moves for my HercuLien! Connected smoothieboard up, installed pronterface, and a power supply and Boom, operational!
-
—
—
Well I got some movements, trying different speed, anything over 250mm will make a bumping sound when changing direction while the gantry is moving in a cross pattern
Well I got some movements, trying different speed, anything over 250mm will make a bumping sound when changing direction while the gantry is moving in a cross pattern
-
—
—
Finally! This I think is a good point to stop tweaking for now
Finally! This I think is a good point to stop tweaking for now.
-
—
—
Getting a lot of z-ribbing still. It perfectly lines up with my leadscrew so I'm assuming some sort of software vs mechanical problem?
Getting a lot of z-ribbing still. It perfectly lines up with my leadscrew so I’m assuming some sort of software vs mechanical problem?
-
—
—
Just a little printer bling added to HercuLien
Just a little printer bling added to HercuLien.
-
—
—
Much much better with 6mm retract and modifying layer height to 0.1920
Much much better with 6mm retract and modifying layer height to 0.1920.
-
—
—
Its printing! Though it needs quite some dialling in at this point
Its printing! Though it needs quite some dialling in at this point.
-
—
—
I don't understand why my pieces are not becoming flush
I don’t understand why my pieces are not becoming flush. Should I be using washers? Alignment is horrible all around.
-
—
—
Hey there. After a long time i'm back
Hey there. After a long time i’m back. Had some ups and downs with my eustathios the last months. but nothing i can’t solve. But now i’m a little bit clueless. The printer seems to have problems with diagonal movements. I can not find any fault in the mechanics. Some ideas? Am i blind?
-
—
—
I have a question about placing the endstops
I have a question about placing the endstops.
-
—
—
If anyone is using the belt tensioners in the picture ( ), I think the belt position is off by about 1.5mm
If anyone is using the belt tensioners in the picture (http://www.thingiverse.com/thing:854301), I think the belt position is off by about 1.5mm. I fixed it and added a new version (1.3), but haven’t had a chance to test it yet. If you printed a set, sorry about that.
-
—
—
Hi guys, I've been contemplating about building a 3D-printer for a while now and I came across these wonderful designs
Hi guys, I’ve been contemplating about building a 3D-printer for a while now and I came across these wonderful designs. I think I have my mind set on building the mighty HercuLien since I recently gained access to Ultimaker 2 and I can now print the parts :)
-
—
—
Thanks to the fantastic @Eric Lien I now have a functioning Eustathios V2!
Thanks to the fantastic @Eric Lien I now have a functioning Eustathios V2!
-
—
—
Does anyone have the exact dimensions of the aluminum build plate for the herculien I can not seem to find the measurements in the BOM or on the instructions
Does anyone have the exact dimensions of the aluminum build plate for the herculien I can not seem to find the measurements in the BOM or on the instructions.
-
—
—
Design decisions upfront. While we already built the frame there are still some design decisions left
Design decisions upfront.
-
—
—
Does anyone have a rough estimate of how many t slot nuts are needed for the herculien?
Does anyone have a rough estimate of how many t slot nuts are needed for the herculien? Also are they m5 or m3. Thanks.
-
—
—
If anybody wants to play around with a Chimera version of the carriage here is where I left off
If anybody wants to play around with a Chimera version of the carriage here is where I left off. It is not my best work, and the part cooling duct looks like a bird beak… but it should work just fine. With some TLC it could be a pretty compact dual extrusion carriage for either HercuLien or Eustathios. It could work for Cylops too… but it would need removal of the beak on the part cooling duct.
-
—
—
Just a fyi for anyone building a Herculien, trimcraftaviationrc has added some new items since the BOM was last updated
Just a fyi for anyone building a Herculien, trimcraftaviationrc has added some new items since the BOM was last updated. I think the following are are equivalent to the mcmaster parts, but cheaper, at least if you’re looking at stainless steel versions. When I ordered parts for my Eustathios, I pointed out the printer BOMs and he was nice enough to add a few more items to his inventory.
-
—
—
Alignment is set I think, (and Eric Lien those washers made a difference!), but what is the secret to getting the belts into these slots?
Alignment is set I think, (and +Eric Lien those washers made a difference!), but what is the secret to getting the belts into these slots? Do I cut off some of the knobby part?
-
—
—
Which printer is the best to build?
Which printer is the best to build? I already have build 2 delta printers and have an Ultiamker 2, but I would like to build another printer. Would the Herculien or Eustathios be better for the implementation of an 80c heated camber? I was thinking of printing all of the plastic parts in polycarbonate to deal with the heat from the camber.
-
—
—
Thanks to Chris McIntyre for the printed parts I was able to put my Herculien together
Thanks to Chris McIntyre for the printed parts I was able to put my Herculien together. This thing barely fits through my bedroom door, hopefully when finished I can manage to take it out.
-
—
—
I am finally ordering all of my herculien parts and I can not find the circular gt2 belts and I am a bit confused with the ordering of the metal for the bed and I can not find the stls for the drill templates
I am finally ordering all of my herculien parts and I can not find the circular gt2 belts and I am a bit confused with the ordering of the metal for the bed and I can not find the stls for the drill templates. I hope someone can help and I am excited to finally start.
-
—
—
Here's the final-ish version of the clamped V4 carriage
Here’s the final-ish version of the clamped V4 carriage. Heatsink is super rigid now, and the screws pulled everything right together; no filing, sanding, or chiseling required.
-
—
—
Here's some progress on the updated print head
Here’s some progress on the updated print head. I tried to maintain compatibility with the standard V4 carriage as much as possible, but I think some angles got messed up somewhere and it’s hard to track down.
-
—
—
10mm reamer came in, I'm still iterating on the xy belt connection, and trying to maximize internal envelope and packaging
-
—
—
You know how they always tell you to pay attention to details?
You know how they always tell you to pay attention to details? Can you spot what is wrong in picture 1? Picture two shows the assembly in right, but the cause of why I turned it 90 degrees in the first place. I had two components upside down, so it seemed like I had to turn it. You may laugh, I laughed at myself!
-
—
—
Has anyone thought about implementing a heated camber into the euthatios?
Has anyone thought about implementing a heated camber into the euthatios?
-
—
—
I didn't have enough outputs on my printer controller after switching to the Azteeg X5 mini to drive my led lighting strip
I didn’t have enough outputs on my printer controller after switching to the Azteeg X5 mini to drive my led lighting strip. So I am using octoprint system:actions to run the led light strip via the raspberry pi GPIO and a sainsmart 2channel 5v relay board. In the album I have a wiring diagram of how I connected the relay, and videos of the file edits and operation. Below is a quick description of what you need to do on the raspberry pi and octoprint to get this working:
-
—
—
Look what greeted me when I got home
Look what greeted me when I got home. My Herculien build can now continue with my new rods, replacing the not so “precision” rods from a discount vendor.
-
—
—
Hi, All set to build the HercuLien, which will be my 5th machine ...
Hi,
-
—
—
So I finally got the funds to build one of these 3D printers
So I finally got the funds to build one of these 3D printers. I’m having a hard time choosing which one. Either the HercuLien or the Eustathios.
-
—
—
Here are the Inventor Pack n Go files for the stepUP printer that I have been working on (an Ingentis variant) Access the Google Drive Folder (I have yet to set up a github): The main assembly is In the directory: /stepUP
Here are the Inventor Pack n Go files for the stepUP printer that I have been working on (an Ingentis variant)
-
—
—
Finally got some work done for my modified Spider V2 build
Finally got some work done for my modified Spider V2 build. Thanks to +Eric Lien for this wonderful printer and the near-to-perfect github repo with all the stuff. I had some extrusion lying around so i did some cutting and sanding with a friend yesterday and we managed to finish the frame. Instead of drilling holes we used some great connectors that i also had from other projects. We added some additional corner brackets - geometry is perfect as far as we could measure.
-
—
—
A couple of questions about leadscrews: * Misumi's 400-500mm long, 10-12mm diameter leadscrews have a max runout of 0.27mm, is this likely to cause problems?
A couple of questions about leadscrews:
-
—
—
wanting to create samples of 3D EeZ that I can give away..
wanting to create samples of 3D EeZ that I can give away.. I am thinking like a Ketchup packet… does anyone have any suggestions or know where i can get such a thing done on a low budget
-
—
—
Hey everyone, been lurking for a bit and finally trying to decide on a printer to build
Hey everyone, been lurking for a bit and finally trying to decide on a printer to build.
-
—
—
Now that I am coming closer to working on my z-bed for my Herculien
Now that I am coming closer to working on my z-bed for my Herculien. I am in need of some help getting the MDF bed routed. I could stop my build and start working on my OX again but I would rather finish one before getting on another.
-
—
—
sorry that it's taking me so long to get the eustathios v2 build guide up
sorry that it’s taking me so long to get the eustathios v2 build guide up. i’ve got tons of pics, but just keep getting caught up with work that i haven’t been able to put full focus on completing the build, much less the guide. :/
-
—
—
That feeling you get when you realize you've left the map and the only way through is to roll your own
That feeling you get when you realize you’ve left the map and the only way through is to roll your own.
-
—
—
Already running out of tnut and m5 8mm
Already running out of tnut and m5 8mm. Reinforcement coming soon from McMaster and Carr. In the mean time, I shall use openbuilds components.
-
—
—
I am looking to build a unit with around a 24" x 24" x 24" ( 600 x 600 x 600mm) build volume
I am looking to build a unit with around a 24” x 24” x 24” ( 600 x 600 x 600mm) build volume. Which one of the three would be the best starting point?
-
—
—
Been working on this Ingentis/Eustathios/Herculien Variant for some time now, and now that high school is coming to a close, I can start building it
Been working on this Ingentis/Eustathios/Herculien Variant for some time now, and now that high school is coming to a close, I can start building it.
-
—
—
Tapping all these holes are hard work
Tapping all these holes are hard work. 😣 The hole drilling is also very time consuming. Good thing the drill guide was very well designed. It would have taken much more time measuring.
-
—
—
i just hooked up my ramps to my steppermotors today
i just hooked up my ramps to my steppermotors today. i can only get the motors to turn one direction, they are just holding still and making noises. does anyone know what is causing it.
-
—
—
Eric Lien Would you mind sharing how you came about the angles shown here?
+Eric Lien Would you mind sharing how you came about the angles shown here? I can measure the angles, but they’re all like 23.8818 and the decimals keep coming if I increase precision. I’m trying to re-cad the carriage with a clamp-style mounting method and I want to keep things as compatible as possible.
-
—
—
Long Time no news , but here comes an update .
Long Time no news , but here comes an update .
-
—
—
New version of the carriage duct for people to try
New version of the carriage duct for people to try. Let me know what you think (nice thing is it is an easy swap).
-
—
—
Edit: Taken! I have a whole set of Herculien parts I don't think I'll be using
Edit: Taken!
-
—
—
Talking about making a mess, after Eirkur left I was printing some cubes with this material which we have used to tune in heating and bed temp
Talking about making a mess, after Eiríkur left I was printing some cubes with this material which we have used to tune in heating and bed temp. Is also printing at more speed. Lowered the bed to 90 degrees. Tried 220 degrees head temp, didn’t go well (reel said 230-250) tried 230 and seemed to be Ok until infill it was not solid and was curling up, tuned to 235 and got a lot better. Left for an hour… And this was what the result was when I got back.
-
—
—
Did a test print on a Ultimaker2 using PETG filament from 3dPrima First print with this filament
Did a test print on a Ultimaker2 using PETG filament from 3dPrima
-
—
—
Live Streaming Gus Montoya 's replacement V2 bearing holders
Live Streaming +Gus Montoya ’s replacement V2 bearing holders. Testing ABS filament from atomicfilament.com printing on my FuseMatic from Maker’s Tool Works.
-
—
—
I give you the nightmare that is the black Euth's first print using slic3r for the first time in over 3 years
I give you the nightmare that is the black Euth’s first print using slic3r for the first time in over 3 years. The original dimensions are 50.80.
-
—
—
Well, I have to admit that I am horrible at cad
Well, I have to admit that I am horrible at cad. I am trying to varify the measurements on this cad drawing. But I can’t seem to do it without screwing up the model in solidworks. Can any one please tell me what the distance measurents are for the following 5 distances?
-
—
—
Hi, might be a silly question but I can't get my head around how the pair of spherical bearings in the XY blocks works - I can understand if there is a single spherical bearing it will compensate for minor misalignment but if
Hi, might be a silly question but I can’t get my head around how the pair of spherical bearings in the XY blocks works - I can understand if there is a single spherical bearing it will compensate for minor misalignment but if there is two (even close to each other) it will force the rod to pass through perfectly straight?
-
—
—
Here's the binding at slow speed
Here’s the binding at slow speed
-
—
—
Hey guys, I was wondering round the internet again last night in search for another 3d printer
Hey guys, I was wondering round the internet again last night in search for another 3d printer. I found this which is pretty much exactly what I was looking for but its a little big. How hard would it be to scale the Eustathios down to around an 8-10” build volume?
-
—
—
At 200% for break in code motors at 1.15 current and not a single grinding sound...drop down to less then 40mm a sec death comes walking in
At 200% for break in code motors at 1.15 current and not a single grinding sound…drop down to less then 40mm a sec death comes walking in
-
—
—
Ok this is new...everything is built ran the break in code no binding and I jogged the moves around a all looked good
Ok this is new…everything is built ran the break in code no binding and I jogged the moves around a all looked good. so I wanted to try a small test cube . All of a sudden I hear horrific binding noises. I watched it a little and noticed it was only during slow movements in x axis. So I did some more test… Any fast movements will move just fine but if I home it its binding up but not skipping steps: so I realigned everything and I’m still having the issue..:
-
—
—
Sorry for asking, but what is the length of the aluminum bars?
Sorry for asking, but what is the length of the aluminum bars? What is the length of the bars in the platform? And what is the length of the closed belts components, the one in the bottom and the ones in the x,y? Can’t find it in the BOM.
-
—
—
So I'm trying PID auto tune for my hotend and it keeps swinging 10degrees each way my bed is functioning fine.i can't figure it out and I'm still pretty unfamiliar with config for smoothieware
So I’m trying PID auto tune for my hotend and it keeps swinging 10degrees each way my bed is functioning fine.i can’t figure it out and I’m still pretty unfamiliar with config for smoothieware. Does any one have any idea? My thermistor is riorand 100k thermistor, and I have he rr100k in my config selected as I think that’s the right one
-
—
—
Dam this thing looks nice hopefully I'll have it printing today knock on wood
Dam this thing looks nice hopefully I’ll have it printing today knock on wood
-
—
—
The "B" pile. Those who know me, know how picky I am with parts I create for my personal use
The “B” pile. Those who know me, know how picky I am with parts I create for my personal use. They would also probably say these parts are perfectly fine. A mixture of PETG, PET+, ABS and CF ABS. I think enough to make 4-5 Eustathios V2 gantries. Once I have some spare time to sort through it all I’ll donate to the Print it Forward campaign.
-
—
—
Making good progress again on my Herculein build
Making good progress again on my Herculein build.
-
—
—
So I have basically everything wired up to what I believe is correct
So I have basically everything wired up to what I believe is correct. If anyone has a diagram for wiring please share it. Specifically how to wire the relay and the plug. Last thing I want is to fry everything. Also I still plan to clean it up.
-
—
—
Just need to wire it up and pic up my acrylic
Just need to wire it up and pic up my acrylic
-
—
—
Got some printed parts but not all what is needed and I am not exactly sure if I am building a Chamelien or a Herculien, or maybe both....
Got some printed parts but not all what is needed and I am not exactly sure if I am building a Chamelien or a Herculien, or maybe both….
-
—
—
Still a lot of work to do, but it's up and running
Still a lot of work to do, but it’s up and running. I accidentally mounted the extruder carriage backwards, and cracked a few of the bearing holders, so I have to rebuild the top. Other than that, the printer assembly was much easier than I expected. The ball screws seem to be working fine, and the graphite bushings seem to be working too, though I don’t have anything to compare them too. I did have some problems with binding when placing two bushings in a row, but printing a single 60mm NinjaFlex sleeve to hold both together seems to have fixed it.
-
—
—
I am finishing up my designs of a large printer build and had some questions, I was hoping some of you could answer or guide me in the right direction
I am finishing up my designs of a large printer build and had some questions, I was hoping some of you could answer or guide me in the right direction.
-
—
—
Man do I love this inland PETG from Micro center (rebranded Esun I believe)
Man do I love this inland PETG from Micro center (rebranded Esun I believe). It prints so nice, no curl, no shrink, great diameter consistency, sticks like crazy to hairspray treated glass at 75C, layer adhesion is unbelievable. I just wish there were more colors. For $25 this stuff is hard to beat.
-
—
—
Not totally, IHE related but. New in big printer news, the Printrbot Pro
Not totally, IHE related but. New in big printer news, the Printrbot Pro. Two feet/600mm cubed!
-
—
—
Well here is my eustathios for today
Well here is my eustathios for today. I would have to say I’m glad I am doing this. As a teenager building motors, model airplanes, RC airplanes etc. I use to be good at this stuff. I have to get back on my game and this will help me out.
-
—
—
thought I was being smart, but I ended up cracking the case, yet not messing up the bushing as before
thought I was being smart, but I ended up cracking the case, yet not messing up the bushing as before. I hope super glue saves the day.
-
—
—
Marlin firmware issues, am new at Arduino and trying to troubleshoot some problems
Marlin firmware issues, am new at Arduino and trying to troubleshoot some problems. When I use the standard marlin firmware I can control the steppers and hot ends using the Repetier or Matter Control host, however when I load the Azteed X3 v2 board with the Herculien firmware I cannot get anything to function on the board, connecting to the printer gives no error. Is there something I may need to set? I have yet to install the LCD panel, I am guessing that might be it.
-
—
—
Well I have started my twin build, tapping the ends of 18 20x80 extrusions took about 2 hours, glad I had two drills
Well I have started my twin build, tapping the ends of 18 20x80 extrusions took about 2 hours, glad I had two drills. I pre-assembled it without making any holes since I have yet to received my drill templates. Anyways probably a good idea and now I can label the pieces and place t-nuts where they should be.
-
—
—
Euth frame done
Euth frame done
-
—
—
I ordered stepper motors from Robotdigg for my Herculien from the BOM link but I am not sure its the correct one, here is the link it is a 6 pin motor?
I ordered stepper motors from Robotdigg for my Herculien from the BOM link but I am not sure its the correct one, here is the link
-
—
—
Eric Lien 's v4 Carriage and e3d's Lite6 Extruder
+Eric Lien’s v4 Carriage and e3d’s Lite6 Extruder. I think I might bump the model up 5% and reprint. It got this close with just a little work with a drill bit on the carriage…it’s nearly a drop-in replacement.
-
—
—
Make sure you read quantity...needed 4 now have 40....
Make sure you read quantity…needed 4 now have 40….
-
—
—
I've been taking pictures of most of the Eustathios parts as they've been coming in, I figure someone might be useful for some future documentation
I’ve been taking pictures of most of the Eustathios parts as they’ve been coming in, I figure someone might be useful for some future documentation. It’s not quite a stock v2 Spyder build, I switched out some parts because I’m cheap (and will probably end up regretting it), but it should be similar.
-
—
—
The build is definitely going to be challenging to get correct
The build is definitely going to be challenging to get correct. I’m sure to have alignment issues. Also I hope I didn’t royally screw up my bushings, all I had was vice grips to press them in. I don’t have a clamp of any kind or a bench vice. Received the one wrong size linear bushing… LM12UU vs a LM10UU. Lastly need to enlarge the hole in the frame. The hole is suppose to be bigg enough for the screw to go in correct?
-
—
—
Had to pull my AliRubber silicon heater off my bed and about 1/3 of the sticky stuff came off
Had to pull my AliRubber silicon heater off my bed and about 1/3 of the sticky stuff came off. It seems that it would probably stick ok-ish if I put it back on, but I’m keen to hear other people’s thoughts first.
-
—
—
I can't seem to get my E3Dv6 on the Eustathios V4 print head
I can’t seem to get my E3Dv6 on the Eustathios V4 print head. This is as far as I could get it on when I attempted to test fit it. I’m afraid my printer might be printing a bit on the large side for some reason, as things always seem tighter than they should be.
-
—
—
Eustathios build progress
Eustathios build progress
-
—
—
Has anyone tried the Pico hotend?
Has anyone tried the Pico hotend?
-
—
—
Enough parts have come to start on the build
Enough parts have come to start on the build. I’m still missing some wire, and the viki 2.
-
—
—
I want to build this sooooo freaking bad!
I want to build this sooooo freaking bad!
-
—
—
Dual Extruders? I wanted to get some feedback on what everyone is using for extruders
Dual Extruders? I wanted to get some feedback on what everyone is using for extruders. I ordered one of the E3Dv6 (1.75) for fine printing but what is a good alternative hot end for fast printing? also how do you go about preventing the other hot end from hitting your print?
-
—
—
Why is it so dead? Anyone making anything on their 3d printer or making progress on their build?
Why is it so dead? Anyone making anything on their 3d printer or making progress on their build? I’m still wainting on my viki LCD. It’s out of stock…
-
—
—
Hi All! I'm in the process of building a HercuLien and am in need of the printed parts
Hi All!
-
—
—
Community request, can anyone lend me their camera to film a assembly instructions for the Eustathios V2?
Community request, can anyone lend me their camera to film a assembly instructions for the Eustathios V2? I’m in San Diego California. I can use my 4 plus year old cell phone but it’ll come out crappy.
-
—
—
Just an update on the build
Just an update on the build.
-
—
—
Wow, what a difference adding 10deg C on the hot end makes on the effectiveness of Bowden retracts with PETG
Wow, what a difference adding 10deg C on the hot end makes on the effectiveness of Bowden retracts with PETG. This Inland brand PETG is so much nicer to print with than the Red MadeSolid PET+
-
—
—
I have purchase the Azteeg X3 controller, what firmware is recommended or preferred for the Herculien?
I have purchase the Azteeg X3 controller, what firmware is recommended or preferred for the Herculien? is there a sample configuration file I can view for setting things up? Thanks!
-
—
—
My low budget build. The frame is build from wood
My low budget build. The frame is build from wood.
-
—
—
So, I got an e-mail today from the people at Onshape saying I got Model of the Week (Which is apparently a thing) for my CAD model of the Eustathios
So, I got an e-mail today from the people at Onshape saying I got Model of the Week (Which is apparently a thing) for my CAD model of the Eustathios. I’m having a real hard time accepting this, as most of the work is not my own, and so, +Eric Lien , +Jason Smith , +Tim Rastall and anyone else who’s made significant contributions to the Eustathios/Ingentis family of printers, please let me know if there’s anything you’d like me to do in return.
-
—
—
Hey, we made this with a lot of effort and passion, will be great to get some diffusion, so if you like our product, please help us to spread the word
Hey, we made this with a lot of effort and passion, will be great to get some diffusion, so if you like our product, please help us to spread the word. For more info go to www.drotix.com! Thanks!
-
—
—
Following up from Seth Messer 's thread here: I received my 2 pieces of 360mmx345mm Borosilicate glass from Cincinnati Gasket & Industrial Glass today
Following up from +Seth Messer ‘s thread here: https://plus.google.com/+SethMesser/posts/BhqfYwSN2cB
-
—
—
Does anyone know what the quality of Robotdigg's rotary and linear bearings is like?
Does anyone know what the quality of Robotdigg’s rotary and linear bearings is like? Been caught out by poor quality bearings before.
-
—
—
octprint on printers could be getting cheaper
octprint on printers could be getting cheaper
-
—
—
I am building the Herculien but thinking of changing the Z-axis and platform using the Eustathios design, anyone do this?
I am building the Herculien but thinking of changing the Z-axis and platform using the Eustathios design, anyone do this?
-
—
—
Anyone have the PayPal info for alirubber specifically the one who goes by Silvia Lang
Anyone have the PayPal info for alirubber specifically the one who goes by Silvia Lang. She sent me a quote but did not include PayPal info
-
—
—
A while ago it was mentioned that pillow blocks could be used instead of printed parts for holding the bearings
A while ago it was mentioned that pillow blocks could be used instead of printed parts for holding the bearings. I gave it a shot and this picture shows the result of some KP008 parts from http://www.aliexpress.com/item/4pcs-8mm-KP08-kirksite-bearing-insert-bearing-shaft-support-Spherical-roller-zinc-alloy-mounted-bearings-pillow/1739080976.html
-
—
—
Hi Folks! I am new here and have started ordering my parts for Herculien build
Hi Folks!
-
—
—
Might not be the best place to ask this but, I was looking at CoreXY
Might not be the best place to ask this but, I was looking at CoreXY. Is the Eustathios better? And why?
-
—
—
Ok this is a strange request. I guarantee it's not out of laziness but more of efficiency and material utility
Ok this is a strange request. I guarantee it’s not out of laziness but more of efficiency and material utility.
-
—
—
Ok guys I need some more help again
Ok guys I need some more help again.
-
—
—
Anyone else has a link to a less expensive powersupply(I'm using the link from the google sheets)?
Anyone else has a link to a less expensive powersupply(I’m using the link from the google sheets)? I already have one but it’s a 12v unit. :(
-
—
—
Printing parts to my colleague, is it the first Herculien in Sweden?
Printing parts to my colleague, is it the first Herculien in Sweden?
-
—
—
End caps for 20-20
End caps for 20-20
-
—
—
Hi all, First post. I'm planning to build an ingentis/eustathios style printer and this is currently where I'm at
Hi all,
-
—
—
I printed the test cubes and lowered the acceleration speed from 9000 to 1500, tighten the tension belt and jerk 20 to 30 but the vertical ring is still there
I printed the test cubes and lowered the acceleration speed from 9000 to 1500, tighten the tension belt and jerk 20 to 30 but the vertical ring is still there. I noticed that lining the three cubes in the same print axis, the vertical ring is consistent (see image). Its not as obvious now but it is still visible.
-
—
—
I have a quick question, i infected a friend into building his own Eustathios ( which means I'll be building it for him)
I have a quick question, i infected a friend into building his own Eustathios ( which means I’ll be building it for him). He ran across this on kickstarter and wants to know if the hotend is only good for like materials or can you print ABS, PLA, Ninjaflex at the same time? I told him no because of the different temperature requirements for each filament. But as always I want to consult the community to see if I missed something.
-
—
—
Thank you Derek Schuetz , the build will continue (after my midterms and finals)
Thank you +Derek Schuetz , the build will continue (after my midterms and finals). I should have take a selfie with your dog’s. They were really happy and joyful :)
-
—
—
So, I finally gave in. After 2 failed 3-hour prints, I went ahead and just totally removed my second hotend which I have never used and was only giving me problems
So, I finally gave in. After 2 failed 3-hour prints, I went ahead and just totally removed my second hotend which I have never used and was only giving me problems. So, my question to you all is, has anyone gotten dual extrusion to work on an Eustathios? I’m 99%sure I’m going to move to Eric Lien’s single extruder carriage during my coming printer re-build, but I wanted to pick some brains to see if it’s possible to salvage the dual extrusion configuration I was so keen on having. If you HAVE got dual extrusion working reliability, can you share your setup?
-
—
—
"machined" some pulleys from robotdigg so I can use the Eustathios V1 setup with the steppers in the base
-
—
—
How straight are your shafts for Eustathios?
How straight are your shafts for Eustathios? Just noticed that my 10mm shafts are no entirely straight, one is around 80 micron untrue in the center of the xy gantry. This seems to be (allmost) within the specs of my supplier as it says “straightness: 50µm/300mm”. Will I sees “slalom” lines in my printed objects? Or nothing to worry?
-
—
—
Eric Lien asked me how my build was going--- Well, I am not as far along as I hoped to be, but I am picking up speed, thanks to Daniel Salinas great instructions page
+Eric Lien asked me how my build was going— Well, I am not as far along as I hoped to be, but I am picking up speed, thanks to +Daniel Salinas great instructions page. I missed a line item for some bearings, and will be ordering them shortly. here’s a picture of my current state of the build.
-
—
—
Talk to me about leadscrew Z's I see that the Herculien design has both leadscrews constrained at the top and bottom
Talk to me about leadscrew Z’s
-
—
—
Here is a video...
Here is a video…
-
—
—
My Eustathios is finally printing. I had to modify many of the parts as I am using non Eustathios design e.g
My Eustathios is finally printing. I had to modify many of the parts as I am using non Eustathios design e.g. 36 teeth belt gear, 8mm rods, etc. I am using what I have in stock. Right now, it is running on 12V RAMPS, non heated bed. When I have time again, I can try to upgrade to 24V and put up the casing.
-
—
—
So I guess this means I'm building a Herculien
So I guess this means I’m building a Herculien. I only have the extruded left to print out then I think I’m done. I also just placed the order for all the smooth rods and lead screws from Igus. I can’t wait to get started and place my order for Misumi tomorrow. p.s. I think I will also get the smoothie board 5 with E3d light hotends.
-
—
—
When your local electronics store only carries 12v fans...
When your local electronics store only carries 12v fans…
-
—
—
A bunch more photos, sadly no progress
A bunch more photos, sadly no progress.
-
—
—
Z Axis done, gantry will be up tonight!
Z Axis done, gantry will be up tonight! Thank you +Alex Lee and Roxy for cutting my aluminum bed plate!
-
—
—
OK here's some photos. Not sure it helps make anything clearer though
OK here’s some photos. Not sure it helps make anything clearer though. You can see in the photos that the left side smooth rod fits into the clamps perfectly, while the right side is a good 2mm too far over.
-
—
—
Hey all, I need a little help figuring out how to assemble the z-axis
Hey all,
-
—
—
Are bushings generally used for both axial and radial motion?
Are bushings generally used for both axial and radial motion? From what I’ve seen the majority are designated neither, most others considered linear and the remaining minority axial and radial. My common sense tells me that the surface of the bushing facilitates the motion so a smooth bushing would work as well axially as radially (as opposed to a regular bearing or linear bearing) but only a small minority are explicitly for both directions . Please advise.. :-)
-
—
—
Print baby, print...I still need three more! (Across two printers)
Print baby, print…I still need three more! (Across two printers)
-
—
—
Anyone into 3D scanning? I am still looking for a practical DIY 3D scanner
Anyone into 3D scanning? I am still looking for a practical DIY 3D scanner. I need to scan items that are 3ft x 3ft.
-
—
—
Looking at the Spider V2 in Solidworks, I don't see the information for the MDF plate that holds the heater
Looking at the Spider V2 in Solidworks, I don’t see the information for the MDF plate that holds the heater. Was this only on the first version? if so what is the rubber heating mat sitting on?
-
—
—
Eric Lien I'm placing some of the final order for my Herculien build and wanted your opinion on alternative lead screws
+Eric Lien I’m placing some of the final order for my Herculien build and wanted your opinion on alternative lead screws. I am considering using 8mm screws in place of the 12mm as listed in the BOM. I’m concerned these may not be sufficiently stiff, but at half the price its tempting. Do you think the weight of the bed necessitates the 12mm screws?
-
—
—
I've been looking through the Eustanthios Spider v2 BOM (google version) and noticed a couple thing that seemed worth mentioning
I’ve been looking through the Eustanthios Spider v2 BOM (google version) and noticed a couple thing that seemed worth mentioning.
-
—
—
Hello. I had not much time for my new 3D printer, but I made a few updates yet
Hello. I had not much time for my new 3D printer, but I made a few updates yet. Printing volume is 330x330x390 (I have 405mm lead screws).My printer have Azteeg x5 mini, E3D volcano. The XY printer’s mechanics are more stable and shake not so much now. I’m experimenting with double Wade extruder and have a question Bond Tech extruder is good enough?
-
—
—
Here's what my herculien has been up to these past few weeks
Here’s what my herculien has been up to these past few weeks.
-
—
—
Ludicris!!!! $30.00 to have FABLAB print 3 bearing holders for the Eustathios V2
Ludicris!!!! $30.00 to have FABLAB print 3 bearing holders for the Eustathios V2. At that rate, it’ll cost more then a $100 to print all the parts. I prefer to wait for the “print is forward”. I guess I’ll put the rest of the expensive parts purchases on hold till I get the 3D printed items.
-
—
—
What's everyone using to control their Herculien?
What’s everyone using to control their Herculien? I’m looking at the smoothie board does anyone have any input on the board?
-
—
—
The wrong time to print supports. Eustathios cooling duct, somewhat clogged
The wrong time to print supports.
-
—
—
Hi, it's much easier to get flanged self-lubricating bronze sleeve bushings from robotdigg for the xy blocks
Hi, it’s much easier to get flanged self-lubricating bronze sleeve bushings from robotdigg for the xy blocks. Would they be suitable replacements for the sintered bushings in the BOM?
-
—
—
Also started to build an Eustathios, extrusions, motors, pulleys arrived
Also started to build an Eustathios, extrusions, motors, pulleys arrived. Printed the first parts.
-
—
—
For those building the Eustathios V2. Be warned, 36 tooth 8mm bore pulleys do not fit in the Z-axis blocks as they currently stand
For those building the Eustathios V2. Be warned, 36 tooth 8mm bore pulleys do not fit in the Z-axis blocks as they currently stand. Not a big deal, but 36 tooth are easier to find than 32 tooth.
-
—
—
What is the best supplier to buy all the Herculien hardware from?
What is the best supplier to buy all the Herculien hardware from? Also is there a good place for all the electronics? I think I’ll buy the aluminum parts precut from Misumi.
-
—
—
I have a stupid question. Looking at the google spread sheets for parts
I have a stupid question. Looking at the google spread sheets for parts. I want to be clear that I don’t order parts twice. In the picture I have provided. Is 3.1and 3.2 the same ? And also what is the difference between XY_Axis_A and XY_Axis_A (Driven Version/Configuration)?
-
—
—
Some movements from my Eustathios build. X/Y axes and carrier looking good [besides some wobble in the shafts until I get my replacements]
Some movements from my Eustathios build. X/Y axes and carrier looking good [besides some wobble in the shafts until I get my replacements]. The bed is also almost done and just needs to be put in place when the new Z screws arrive.
-
—
—
New status update request on Herculien and Eustathios builds
New status update request on Herculien and Eustathios builds. We’ve had some come online with minor tweaks needed. How have everyone progressed in their builds? I essentially have all order-able parts, now waiting on 3d printed parts from the “print it forward”.
-
—
—
Success! I added the shims and that killed most of the noise, there was still a nasty high pitched squeal when making diagonal moves
Success!
-
—
—
Testing a variety of materials
Testing a variety of materials
-
—
—
First moves in xy. Y moves seem great
First moves in xy. Y moves seem great. Not even run the burn in gcode completely yet. X moves are a little noisy. Not yet sure why. I moved one of the pulleys away from the bearing block a little that seemed to help, so perhaps they are rubbing on the bearings?
-
—
—
Design opinion needed! Great designs that I can check out in Solidworks shared by Eric Lien
Design opinion needed!
-
—
—
I need some help figuring out how to get my xy axis smooth
I need some help figuring out how to get my xy axis smooth.
-
—
—
Does anyone have a Herculien BOM with links or one with where to buy the parts?
Does anyone have a Herculien BOM with links or one with where to buy the parts?
-
—
—
7 hour print I'm feeling like its up and running reliably
-
—
—
Another update on borosilicate glass suppliers. The folks at VoxelFactory just emailed me to let me know they are supplying again, but at a higher cost and much longer lead time
Another update on borosilicate glass suppliers.
-
—
—
Just realised I don't have the 8mm bore 32tooth GT2 pulleys for my Z-axis
Just realised I don’t have the 8mm bore 32tooth GT2 pulleys for my Z-axis. Is there any downside to taking 36tooth or 30tooth instead? I’m running 0.9 degree steppers with the misumi leadscrews.
-
—
—
thoughts?
-
—
—
Finally assembling my Eustathios... 3 months late
Finally assembling my Eustathios… 3 months late. However, is the bearing pictured below has a bit of wiggle, is it intended to be snug? Do I have the wrong bearing if so? If the right bearing, have I had an accuracy issue all along I haven’t noticed?
-
—
—
This one wan's easy (for me ;) )...
This one wan’s easy (for me ;) )… but another model in FreeCAD
-
—
—
So .1 layer height out of a .8 nozzle no after cleanup done
So .1 layer height out of a .8 nozzle no after cleanup done. Issues that I noticed were the overhangs had some trouble and the bridging at the bottom never fully closed but cura has no setting to adjust bridging.the helix in the center is almost fully there but I assume since my nozzle size is the Same diameter as the helix twist it was not going to come out at all so that was cool
-
—
—
Howdy everyone. I may have found a supplier for borosilicate glass, custom cut, to replace VoxelFactory (or until VF is able to start providing the service again)
Howdy everyone. I may have found a supplier for borosilicate glass, custom cut, to replace VoxelFactory (or until VF is able to start providing the service again).
-
—
—
Here is a sneak preview of my Herculien variant....
Here is a sneak preview of my Herculien variant….
-
—
—
Does anyone know roughly what the cost to build a Herculien is?
Does anyone know roughly what the cost to build a Herculien is? I have been really amazed with the quality and speed it can achieve.
-
—
—
I already purchased my hot end and got a 12V E3dV6
I already purchased my hot end and got a 12V E3dV6. I choose the 12volt as the RAMPS board was 12v. I checked the build requirements and see 24V. Can I just go the 12V route? I only see the fans (from amazon) that would need to be changed. The SSR looks good.
-
—
—
Eric Lien have you considered making bearing mounts to be corner brace too?
+Eric Lien have you considered making bearing mounts to be corner brace too? are there any cons to this approach?
-
—
—
I'm on Fire... tree parts ... well next week I will not have so much time, so I have to compensate
I’m on Fire… tree parts … well next week I will not have so much time, so I have to compensate.
-
—
—
The Bed Leveling mount. I was thinking in one per day but if I can't at least do two designs in the first day...
The Bed Leveling mount. I was thinking in one per day but if I can’t at least do two designs in the first day…
-
—
—
Got the cable chain installed and cleaned up some wiring while I try to figure out warping issue
Got the cable chain installed and cleaned up some wiring while I try to figure out warping issue.
-
—
—
My Eustathios V2 in FreeCad, I don't have Solidworks so i'm trying to replicate the work in FreeCAD, this also serves me to learn a CAD tool
My Eustathios V2 in FreeCad, I don’t have Solidworks so i’m trying to replicate the work in FreeCAD, this also serves me to learn a CAD tool.
-
—
—
Warping issues? So I was printing perfect with hatchbox abs stuff was sticking well to the build platform minimal warping and then I got some new filament and the stuff comes right off the bed and has some pretty amazing
Warping issues?
-
—
—
Eustathios V2.. all parts ordered. Let the flood of UPS/USPS/FedEx drivers to my domicile commence
Eustathios V2.. all parts ordered. Let the flood of UPS/USPS/FedEx drivers to my domicile commence.
-
—
—
Simplify3D users, especially for the Eustathios V1/V2 (preferably V2) users, might you share what the 'Other' settings should be?
Simplify3D users, especially for the Eustathios V1/V2 (preferably V2) users, might you share what the ‘Other’ settings should be? I’m trying to prepare for everything as best I can before the build begins. Would love to just get used to the software too. Also, for those of you with a Smoothieboard, would you also be willing to share your firmware/configurations for the Eustathios V1/V2 (preferably V2).
-
—
—
Eustathios V2 part updates -- must read if you are buying parts Guys/gals, I just talked to Francois over at VoxelFactory.com and they are presently not selling boro glass (raw or cut to size)
Eustathios V2 part updates – must read if you are buying parts
-
—
—
This cable chain was in the HercuLien printable stl files
This cable chain was in the HercuLien printable stl files. Does it actually get used somewhere? If it does, I have no idea how many links need printed, but I was having fun printing them.
-
—
—
ATTENTION: Community's participation and input needed. I've offered to move the Eustathios V2 BOM to a Google Sheets document (Eric will approve it and add it to the root GitHub README), and have been trying to get the
ATTENTION: Community’s participation and input needed.
-
—
—
So i have the frame built. Just the outer cube though
So i have the frame built. Just the outer cube though. I’m getting in the last parts to fix my mendel, so I can finish printing out the rest of the parts. In the meantime I was wondering how far down these extrusions need to be placed and how large should I make the bed? Thanks!
-
—
—
After much banging my head against the wall and losing an extruding I think I'm finally to a good printing time (knock on wood)
After much banging my head against the wall and losing an extruding I think I’m finally to a good printing time (knock on wood). I have printed 2 complete dragons which I’m using to adjust bed adhesion (done complete) and retraction settings (almost there just have to find the sweet spot) this was print with a 1.2 mm nozzle at .2 layer height which amazes me the detail I can get with that large of a nozzle
-
—
—
1 of 2 orders are in. Heat pad almost here, control board is almost here
-
—
—
Another Eustathios Spider (V1) in the making
Another Eustathios Spider (V1) in the making. I finally got around to starting this build last night. I will most likely keep it as V1 since I already had the BoM for it and prefer to have my motors tucked away.
-
—
—
Eric Lien did you decide on a new home for the BOM for Eustathios V2 (and HercuLien for that matter)?
+Eric Lien did you decide on a new home for the BOM for Eustathios V2 (and HercuLien for that matter)? I ask because I checked to see if there were updates to the Eustathios V2 repo and saw this commit: https://github.com/eclsnowman/Eustathios-Spider-V2/commit/019a181e6f23987f14db8ea5f950ce1d6d5c3ecc
-
—
—
I have a question for those who ordered from robotdigg recently?
I have a question for those who ordered from robotdigg recently? How long did it take you to get your order (in US)? Did you pay standard Air Mail shipping or more expensive FedEx/UPS?
-
—
—
I started off wanting to build the Eustathios Spider V2
I started off wanting to build the Eustathios Spider V2. These are the pieces I have printed in Orange. If anyone is interested, they are almost free + shipping. I decided to go for the gold and build the HercuLien.
-
—
—
Received the Misumi extrusion yesterday and the Bondtech extruder parts a week ago
Received the Misumi extrusion yesterday and the Bondtech extruder parts a week ago. +Ashley Webster has the Azteeg controllers and the various motion related components from RobotDigg. Looks like we’re sparking-up the frame soon, just need to figure out where to build these beasts ;) . Many many thanks to the creators and contributors of these beautiful machines. I hope to give-back somehow, and even though we are printing our own parts to use on these builds, maybe I can provide a print-forward for a fellow Canadian enthusiast thereby saving freight costs from the US. Cheers and good journeys all!
-
—
—
Can I take this HercuLien BOM and build my printer from the top down?
Can I take this HercuLien BOM and build my printer from the top down? It does seem to be setup that way.
-
—
—
Corner brackets and Z shafts have arrived today
Corner brackets and Z shafts have arrived today.
-
—
—
After a year of using Makerbot and a few months of Form1, I've decided to build something more customizable
After a year of using Makerbot and a few months of Form1, I’ve decided to build something more customizable. After checking numerous designs, the Eustathios looks like a very good place to start, and I really like the kinematics on this build. However, I do like the option of direct extrusion, or just mounting some additional equipment (not too heavy, though) on the carriage, next to the bowden extruder. Therefore, I’m a bit doubtful about the 8mm rods, and thinking I need something more rigid. And, perhaps, a switch to the 4040 extrusion.
-
—
—
I did something very stupid. I switched the power inputs to my RAMBo controller
I did something very stupid. I switched the power inputs to my RAMBo controller. Anyone else done this and only had to replace the blow fuses, not the entire board? (Looking for peace of mind right now :) )
-
—
—
"Open18" is coming together at MRRF. I think he's posted renderings here last week.
-
—
—
Here's some progress on the Eustathious re-creation in Onshape
Here’s some progress on the Eustathious re-creation in Onshape. I’m going to start by recreating the vanilla Eustathios as best I can, though of course with a few tweaks here and there. Of course, the printed parts are all blue to match my printer’s parts (The Blustathios maybe?). I’ll be adding a few things specific to my printer (XY carriage comes to mind) but it should be pretty stock.
-
—
—
I think this is the Alumimaker 2 design that won that Misumi contest a month ago
I think this is the Alumimaker 2 design that won that Misumi contest a month ago.
-
—
—
Eric's HercuLien building parts today at MRRF
Eric’s HercuLien building parts today at MRRF.
-
—
—
Got it all wired up. Its moving really nicely
Got it all wired up. Its moving really nicely. Need to get the extruders hooked up tonight. +Eric Lien wewt!!!
-
—
—
Any idea where to buy the extrusion in Canada
Any idea where to buy the extrusion in Canada. I wish to avoid Misumi as they are in US (bad exchange right now) and they charged me 200$US of shipping on my last 90$ order (and you don’t know that until they ship).
-
—
—
SMW3D, ROBODIGG, and ENCO deliveries last evening will make for a nice Saturday in the workshop on my HercuLein!
SMW3D, ROBODIGG, and ENCO deliveries last evening will make for a nice Saturday in the workshop on my HercuLein!
-
—
—
Does anyone happen to know what thermistor ali rubber are putting in their beds?
Does anyone happen to know what thermistor ali rubber are putting in their beds? They say ‘100k’, but that seems to be a bit generic.
-
—
—
I have begun recreating all the Eustathios files in Onshape
I have begun recreating all the Eustathios files in Onshape. I have made the document public and you can find the link below. You can also probably just search the public documents for “Eustathios”. Of course, this assumes you have got a Beta invite to Onshape.
-
—
—
Isaac asked for Eust photos...
Isaac asked for Eust photos…
-
—
—
BondTech and HercuLien at Midwest RepRap Fest
BondTech and HercuLien at Midwest RepRap Fest
-
—
—
Anyone found an alternative for the a_7z41mpsb08m from SDP/SI?
Anyone found an alternative for the a_7z41mpsb08m from SDP/SI? (The sleeved bearings for the eustathios carriage).
-
—
—
Any updates on who is going to Print it forward next?
Any updates on who is going to Print it forward next? Having wishful thinking that someone will print my parts so it’ll arrive by end of month. And I can start building away.
-
—
—
There were some questions about getting self-aligning bushings to align and move smoothly
There were some questions about getting self-aligning bushings to align and move smoothly. Dug up this classic post by +Tim Rastall explaining everything you need to know.
-
—
—
Anyone have tips for pressing and aligning the self aligning bearings?
Anyone have tips for pressing and aligning the self aligning bearings? I’m having trouble getting them to slide nicely. Getting lots of drag.
-
—
—
For those of you that have purchased your parts off of misumi (for eustathios v2, herculien, or the like), the purchase procedure for them is a little unintuitive
For those of you that have purchased your parts off of misumi (for eustathios v2, herculien, or the like), the purchase procedure for them is a little unintuitive. it wants to charge me freight, yet shipping costs show $0? i’m a little weary of unforeseen freight charges (the total for parts for eustathios v2, JUST on misumi is at $485.06 as it is!)
-
—
—
This is good stuff, but man it's expensive
This is good stuff, but man it’s expensive.
-
—
—
In my Eusthathios build, I'm having trouble inserting the LM8UU linear bearings into the carriage (an earlier version of Eric Lien's V4)
In my Eusthathios build, I’m having trouble inserting the LM8UU linear bearings into the carriage (an earlier version of Eric Lien’s V4). I’ve tried applying acetone (from nail polish) with a q-tip as well as shaving off the inside with an exacto knife. Neither seems to be helping and I worry about the alignment. Has anyone else had this problem or any suggestions?
-
—
—
What type of material are people printing the Herculien?
What type of material are people printing the Herculien? Because of the enclosure it’s most likely ABS for the high glass transition point but what infill % are people using?
-
—
—
This is where I walked away from the open18 last night
This is where I walked away from the open18 last night. Think it will be done for this weekend?
-
—
—
Anyone that will be at MRRF this weekend, do any of you have 2 of the 32 tooth 10 mm robotdigg pulleys they would want to sell?
Anyone that will be at MRRF this weekend, do any of you have 2 of the 32 tooth 10 mm robotdigg pulleys they would want to sell? I’m 2 short. I can either use a mix of 36 and 32 tooth or print two 32 tooth pulleys right now.
-
—
—
For the Eustathios, what size bolt are people using for the end stops?
For the Eustathios, what size bolt are people using for the end stops? It seems like M3 is too large for the E3D end stops I have and the 3D part.
-
—
—
Can't get Autodesk Fusion 360 to open Eric Lien 's Eustathios Spider V2 skp file
Can’t get Autodesk Fusion 360 to open +Eric Lien ‘s Eustathios Spider V2 skp file. Uploading through the app stalls every time and when I add it on the web page I can’t open in in the app. Any ideas? Someone else with Fusion happy to share it with me?
-
—
—
It didn't last long but I'm tired of waiting for belts so I made some makeshift ones to at least see some life
It didn’t last long but I’m tired of waiting for belts so I made some makeshift ones to at least see some life.
-
—
—
Finally getting back to Eustathios and got all my extrusion tapped
Finally getting back to Eustathios and got all my extrusion tapped.
-
—
—
Blew the fuse in my plug outlet that came with it...after enabling both hotends and bed, luckily I have extras and everything is still good
Blew the fuse in my plug outlet that came with it…after enabling both hotends and bed, luckily I have extras and everything is still good. Other then that I am 2 small belts from printing(calibrating). Dam China post and sdp-si I want to finish this thing
-
—
—
Hi, what are the pros and cons of the different ways of connecting the t-slots?
Hi, what are the pros and cons of the different ways of connecting the t-slots? I’ve been looking at gussets, tapping the ends and 3d-printed braces. I’m looking for accuracy in getting them square. Are any of the above adjustable or do you have to get it spot-on with the install?
-
—
—
Herculien loot box courtesy of SMW3D .
Herculien loot box courtesy of +SMW3D. 😁 One step closer.
-
—
—
Just finished a printable electronics case for my herculien build
Just finished a printable electronics case for my herculien build. I’m pretty happy with the results.
-
—
—
Has anyone tried this?
Has anyone tried this?
-
—
—
FYI, files are up. Enjoy. Originally shared by Eric Lien I am finally ready to officially release my Eustathios Spider V2 variant of the great prior work by Jason Smith (Eustathios) and Tim Rastall (Ingentis)
FYI, files are up. Enjoy.
-
—
—
Has there been any thoughts about adding an inductive sensor or mechanical z probing or touch sensor to the z bed for auto-leveling to the herculien platform?
Has there been any thoughts about adding an inductive sensor or mechanical z probing or touch sensor to the z bed for auto-leveling to the herculien platform?
-
—
—
Ordered a Smoothie board today for my HercuLein build, has anyone in this group used one for their 3d printer yet?
Ordered a Smoothie board today for my HercuLein build, has anyone in this group used one for their 3d printer yet?
-
—
—
Holy Crap I might actually finish this thing before MRRF
Holy Crap I might actually finish this thing before MRRF. right now the printable dimensions are looking like 14x14x19ish”. Also known as bigger then Im ever gonna print :D
-
—
—
I just wanted to see who might be going out to MRRF March 20-22
I just wanted to see who might be going out to MRRF March 20-22. I will have both my printers out there. And +Martin Bondéus from Bondtech is flying in from Sweden and driving down with me (I am very excited to talk shop and crack some beers with my friend from across the pond). I would love to meet some of you guys in person.
-
—
—
I just received my fedex notification that my bondtech item will arrive on Friday !
I just received my fedex notification that my bondtech item will arrive on Friday ! So excited :) To bad it’s only going to go to the future build parts bin. :(
-
—
—
got my bondtech v2 extruder from the beta program :) so i have the extruder, and the viki2 lcd
got my bondtech v2 extruder from the beta program :)
-
—
—
Eh?
Eh?
-
—
—
Learned about this today. Any thoughts on making a public Ingentis/Eustathios/Herculien that anyone can view and contribute to?
Learned about this today. Any thoughts on making a public Ingentis/Eustathios/Herculien that anyone can view and contribute to?
-
—
—
Dropped my old z axis in from Creo
https://www.youtube.com/watch?v=MlalQhaU0C8&feature=youtu.be
-
—
—
Finally getting the hang of fusion 360
https://www.youtube.com/watch?v=5mE39OcIcuc&feature=youtu.be
-
—
—
Finally warmed up here in Kentucky, so I could get into the workshop
Finally warmed up here in Kentucky, so I could get into the workshop. Test fit of the first components!
-
—
—
got my first eustathios part in.. a viki2 lcd
got my first eustathios part in.. a viki2 lcd. one very very very small step towards completion.
-
—
—
howdy everyone. :D i was wondering if anyone was still "Paying it forward" from ?
howdy everyone. :D
-
—
—
Finally took the time to design a lid stop
Finally took the time to design a lid stop. Prints as one piece with the peg captive in the slot. The slot side uses a 5mmx16mm bolt which just bottoms out on the extrusion allowing the bolt to act as a fixed pivot. Then just adjust the ped side to open to your desired amount.
-
—
—
I have been trying to think of a way to access the top of the printer without having to hinge up the whole lid
I have been trying to think of a way to access the top of the printer without having to hinge up the whole lid. I think I found a solution.
-
—
—
Greatest feeling is getting it working after hours of trying to understand marlin with no previous experience beyond configuration.h screen
Greatest feeling is getting it working after hours of trying to understand marlin with no previous experience beyond configuration.h screen
-
—
—
What I did today... The black paint bled a bit, which is disappointing, but otherwise it turned out pretty well
What I did today…
-
—
—
All wired up except for pi to Aztega (waiting on connector) now I just need to remember how to flash marlin again
All wired up except for pi to Aztega (waiting on connector) now I just need to remember how to flash marlin again
-
—
—
Aluminum extrusion all cut to size thanks to Mike Smith
Aluminum extrusion all cut to size thanks to Mike Smith. Do you need to drills and tap or can you use the brackets that Misumi provides?
-
—
—
Well my herculien build is finally coming along
Well my herculien build is finally coming along. Z axis is all buttoned up and lexan side and back panels are installed. Best of all… Full documentation of each build step up to this point. Phew its taking forever but it finally is starting to resemble a printer.
-
—
—
9 8020's tapped and ready for the build
-
—
—
Well this is an idea
Well this is an idea.
-
—
—
It moves! Jerkyness as I was using jog controls
It moves! Jerkyness as I was using jog controls. Noisy because I’ve not epoxied the v shaped extrusions on yet (so they vibrate)
-
—
—
To those that have started their Herculien build, how close are you to being done?
To those that have started their Herculien build, how close are you to being done? It’s exciting to see some running builds. I’m still waiting to start, so I keep happy viewing others builds. Also I’m self learning solidworks. What a powerful and yet complicated software. I hope I grasp it sooner then later.
-
—
—
Throwing some PLA down with the volcano: 1.2mm nozzle, .7mm layer height, 1.2mm shell, 1.4mm bottom/top, 15% infill, 28mm/s speed, 240C hotend, 70C bed
Throwing some PLA down with the volcano: 1.2mm nozzle, .7mm layer height, 1.2mm shell, 1.4mm bottom/top, 15% infill, 28mm/s speed, 240C hotend, 70C bed. Model dimensions: 82mm x 103mm x 71mm. Total time: 75 minutes.
-
—
—
Laser cut some new side panels to enclose things
Laser cut some new side panels to enclose things. Now I just need to sort out a lid.
-
—
—
Oh yes. Thanks to Brandon Satterfield .
Oh yes. Thanks to +Brandon Satterfield. I am getting all my extrusion together. Well most of it since I made a mistake in my reading of the Bom so now I will need another 1500 2020. Yay, I am feeling super duper excited.
-
—
—
Ok so nice I had to post: From my investigation of various filaments, I found that one company does indeed make bronze and also copper infused filament which gives the superman painted effect
Ok so nice I had to post: http://3dprint.com/47296/3d-printed-superman
-
—
—
New filament from top to bottom Ninjaflex, POM, PLA. :)
New filament from top to bottom Ninjaflex, POM, PLA. :)
-
—
—
Mr Lien, being pretty awesome. I'll forgive him for murdering my surname
Mr Lien, being pretty awesome. I’ll forgive him for murdering my surname.
-
—
—
Known about these hinges from work thought they'd be perfect
Known about these hinges from work thought they’d be perfect
-
—
—
Z stage progress!
Z stage progress!
-
—
—
I have started to receive material for my Herculien build
I have started to receive material for my Herculien build. The mdf insulator board was CNC:ed yesterday . The Aluminium frame , Alu healing bed, stepper engines, and some other funny stuffs is ordered . I know there has been a discussion about the cost for the frame and that its probably overengineered . This is My first 3Dprinter and I have choosen to make it very similar to Erics basis design . I do like overengineered stuff :)
-
—
—
Quick question guys, I've never encountered this before
Quick question guys, I’ve never encountered this before. I’m trying to print a eustathios set for +Eric Bessette and I’ve run into this issue with all the slicers I have for the XY Tensioner blocks. It seems like the wall width is under my nozzle diameter. I usually print with an extrusion width of .48mm and I use a .4mm nozzle on an E3D V6 hotend. I can get that wall to slice to a full face if I change my extrusion width settings to .32. Is this something you guys have run into? Workarounds?
-
—
—
Very well packed package from +Mitsumi arrived tonight, I wish my shop was not @ 18 degrees tonight
Very well packed package from +Mitsumi arrived tonight, I wish my shop was not @ 18 degrees tonight.
-
—
—
I was recently quoted $75 from a local glass company to get a 420mm x 430mm x 1/4" of single pane window glass
I was recently quoted $75 from a local glass company to get a 420mm x 430mm x 1/4” of single pane window glass. I did ask them to chamfer the piece so I don’t cut myself handling it.
-
—
—
Slowly progressing forward
Slowly progressing forward.
-
—
—
My build will start shortly, received these printed parts today - Thank you to Alex Lee !
My build will start shortly, received these printed parts today - Thank you to +Alex Lee! Mitsumi order due Friday!
-
—
—
We need to find a way to add this tablet support thing :-) It does look nice
We need to find a way to add this tablet support thing :-) It does look nice.
-
—
—
I have two major questions. 1) Does anyone have experience printing ultra high temperature filament?
I have two major questions. 1) Does anyone have experience printing ultra high temperature filament? I am trying to figure out how I can make an air intake plenum for my 190e cosworth without it melting onto the motor through desert trips. 2) Also anyone can direct me to a DIY 3d scanner that’s moderate in cost and well documented? I’m doing my own research but still not satisfied in what I have found.
-
—
—
So I am doing all the final tweaks on my movement axis on my Herculien
So I am doing all the final tweaks on my movement axis on my Herculien. I got my x and y to have no binding but my z axis is giving me issues. If I keep the z couplers loose and not completely bolted down it moves smoothly but if I tighten instant binding to the axis. I have tried everything and can’t stop the binding. Am I suppose to leave the couplers loose?
-
—
—
Could someone help me identifying which of the three closed belts in the Eustathios BOM is for the Z axis?
Could someone help me identifying which of the three closed belts in the Eustathios BOM is for the Z axis? Thanks.
-
—
—
It looks like the Eustathios Bearing B part at is a bit broken
It looks like the Eustathios Bearing B part at https://github.com/jasonsmit4/Eustathios/blob/master/STL/Eustathios%20Bearing%20Holder%20B%20-%204%20-%20v1.0.stl is a bit broken. Does any have an updated STL file?
-
—
—
Anyone know an alternate source for the A 7Z 4MF2208 part in the Eustathios BOM?
Anyone know an alternate source for the A 7Z 4MF2208 part in the Eustathios BOM?
-
—
—
Hey guys, I'm on the last printed part for my Eustathios build and thought I would share it with you all live via live streaming
Hey guys, I’m on the last printed part for my Eustathios build and thought I would share it with you all live via live streaming. It’s +Eric Lien ‘s fixed Z-Bed Support for his V4 carriage that I slightly modified to accept an Igus lead screw nut. 4 hour’ish print time using PET+ on my MendelMax 3 beta machine.
-
—
—
Eustathios frame arrived today. Building starts tomorrow :)
Eustathios frame arrived today. Building starts tomorrow :)
-
—
—
so stoked seeing everyone's various builds coming together around the same time
so stoked seeing everyone’s various builds coming together around the same time. going out of town for work next week. taking a break from following updates and such is going to be tough but good to keep sanity.
-
—
—
I wonder if Herculien can use these as well
I wonder if Herculien can use these as well. Nvm, the bearing plate in the Herculien looks beefier.
-
—
—
All that work putting it together and now its back in pieces
All that work putting it together and now its back in pieces. :). I’m not a great writer but I’m going to do a series of docs on assembling the herculien and would appreciate anyone else who has one or building one to double check my steps.
-
—
—
Shiny new Z stage coming together. And that black stuff is di-bond before you ask
Shiny new Z stage coming together. And that black stuff is di-bond before you ask.
-
—
—
Huh. Originally shared by null Want to see the BOM that took the cake in our contest?
Huh.
-
—
—
Huh. Originally shared by **** Want to see the BOM that took the cake in our contest?
Huh.
-
—
—
Hi, So I saw someone on reddit building a HercuLien and found this group
Hi,
-
—
—
I am in absolute awe at the size of this thing...the video gave it no justice I don't think I realize what I am creating until now
I am in absolute awe at the size of this thing…the video gave it no justice I don’t think I realize what I am creating until now
-
—
—
Here is a little progress on My Eustathios Spider V2 upgrades
Here is a little progress on My Eustathios Spider V2 upgrades.
-
—
—
So the belts listed on the BOM for Herculien will not be shipping till march 22nd I found a slightly shorter 226mm belt on eBay but I'm not sure if it would be better to go slightly longer or slightly shorter
So the belts listed on the BOM for Herculien will not be shipping till march 22nd I found a slightly shorter 226mm belt on eBay but I’m not sure if it would be better to go slightly longer or slightly shorter. Or +Eric Lien or others have an alternate source?
-
—
—
those of you using for your slicer/app, are you able to install a single license on multiple machines?
those of you using #simplify3d for your slicer/app, are you able to install a single license on multiple machines? i checked their FAQ and also reached out to them (haven’t heard back) to find out before I pull the trigger. thanks!
-
—
—
I am having trouble figuring how to get the 3D printed parts to create my first 3D printer without spending a ton of money
I am having trouble figuring how to get the 3D printed parts to create my first 3D printer without spending a ton of money. I saw in another comment here something about the “Print It Forward Program”. Is that a real thing? If so, how would I go about requesting an invite?
-
—
—
Got all the aluminum extrusions mocked up for my Herculien build this morning
Got all the aluminum extrusions mocked up for my Herculien build this morning. Now I need to tear them down and start doing videos of assembly since I’m waiting on 4 more eccentrics which won’t be here til Friday. Hopefully soon +Eric Lien we’ll have a build doc with pics and videos for building a Herculien. I need to print a gopro tripod mount today while I’m working so I don’t make completely amateur videos :)
-
—
—
I've been looking for a cool 3D printer to build and found the Ingentis and Eustathios last weekend
I’ve been looking for a cool 3D printer to build and found the Ingentis and Eustathios last weekend. I just wanted to say that seeing this active community sealed the deal for me. I’ve ordered a bunch of the materials and am excited to get started. Thanks for all the help you’ve provided so far and (hopefully) will provide in the future.
-
—
—
FIINALLY cleaned up the wiring and installed the lower plexiglass plates
FIINALLY cleaned up the #Eustathios wiring and installed the lower plexiglass plates. Mounted +Eric Lien ‘s new carriage modified for linear bearings and my new Volcano. The acryllic base for my bed warps under heat, so I’ve got some aluminum plate on order. I’ve also got more acryllic on the way for an enclosure and a sheet of PEI for a build surface. This is going to be a whole new machine by the time I’m done with it :)
-
—
—
Cleaned up, re-trammed, printing nylon, and back to using IGUS on the carriage
Cleaned up, re-trammed, printing nylon, and back to using IGUS on the carriage.
-
—
—
Eric Lien you were right. Derek Schuetz 's parts came out nicer than mine so I'm printing a few new ones for myself
+Eric Lien you were right. +Derek Schuetz’s parts came out nicer than mine so I’m printing a few new ones for myself. :D
-
—
—
It begins to take form
It begins to take form
-
—
—
any of you guys into IRC? if so do any of you frequent or any other specific IRC channels for the Ingentis/HercuLien/Eustathios designs?
any of you guys into IRC? if so do any of you frequent #reprap or any other specific IRC channels for the Ingentis/HercuLien/Eustathios designs?
-
—
—
I am about to make an order for heated bed silicone from alirubber
I am about to make an order for heated bed silicone from alirubber. The shipping cost is ~$35 to the US. Does anyone else (especially those in Houston, TX) wanting to do a group buy to save on the shipping cost?
-
—
—
I have been working on some upgrades to my Herculien to improve issues I observed after the initial assembly, burn-in and preliminary prints
I have been working on some upgrades to my Herculien to improve issues I observed after the initial assembly, burn-in and preliminary prints.
-
—
—
I am testing a Smoothieware based Azteeg x5 mini, and Viki2 LCD on my Eustathios
I am testing a Smoothieware based Azteeg x5 mini, and Viki2 LCD on my Eustathios. The motion platform is amazing. I can run 50% faster than I could with my Azteeg x3 mini before I begin to see chatter on decel and quick moves. My only issue is I cannot seem to get the heated bed and hot end to heat up. The display on the Viki2 shows that it is enabled and heating… but the temp never rises.
-
—
—
That point where Eric Lien 's efficiency causes your printer to fly apart because Max Z is still a good Centimeter away from the nozzle
That point where +Eric Lien’s efficiency causes your printer to fly apart because Max Z is still a good Centimeter away from the nozzle.
-
—
—
Printed one of the rod alignment tool that Eric Lien posted to realize I need to print another
Printed one of the rod alignment tool that +Eric Lien posted to realize I need to print another 😯.
-
—
—
Eric Lien just wanted to give a 'thanks' for all the work you put into those solidworks models on the various designs
+Eric Lien just wanted to give a ‘thanks’ for all the work you put into those solidworks models on the various designs. i finally got around to being able to view them. wow at the detail! wish i had the full blown app instead of just a viewer. this’ll come in handy just being able to view/reference them now.
-
—
—
Slicing software: what do you use? I've been using exclusively Cura for the past few months, Slic3r in 2013 for a while
Slicing software: what do you use?
-
—
—
Working on getting the heated bed element for my z plate of the Herculien
Working on getting the heated bed element for my z plate of the Herculien. Does anyone have an email with the exact values to email the chinese supplier? The pig tail alteration would be useful as well.
-
—
—
It's happening. Herculien extrusion being cut. Yay. Brandon Satterfield
It’s happening. Herculien extrusion being cut. Yay. ☺ +Brandon Satterfield
-
—
—
Integrate lighting into my Herculien question. I want to add some LED lighting potentially some white led strips up top
Integrate lighting into my Herculien question. I want to add some LED lighting potentially some white led strips up top. But I know little about electrical. I am running. A 24v PSU and all led strips are 12v is this an issue if I’m running them through the Aztega v3?
-
—
—
I'm elated! Just ordered my bondtech v2 extruder
I’m elated! Just ordered my bondtech v2 extruder. I hope It won’t take long to finish this build. :)
-
—
—
Was buying the last of the parts for Eustathios today, but ran into a problem with the threaded shaft on the BOM: "MTSBRA12-410-S56-Q8", Misumi doesn't seem to carry the variant specified here any longer
Was buying the last of the parts for Eustathios today, but ran into a problem with the threaded shaft on the BOM: “MTSBRA12-410-S56-Q8”, Misumi doesn’t seem to carry the variant specified here any longer. The “S56” and “Q8” are what seem to be giving the search tool trouble.
-
—
—
Hi, First post from me here, I'm trying to get my head around a build and have gone through the STLs and the BOM, as well as a number of posts here
Hi,
-
—
—
curious if any of you have considered/used dual extruders for an e3d chimera or cyclops..
curious if any of you have considered/used dual extruders for an e3d chimera or cyclops.. if so, how’d that go? dual extrusion and the work involved to get it all dialed in worth it?
-
—
—
So just to show a update on my large frame, I have most of my xy gantry done ready to buy and print
So just to show a update on my large frame, I have most of my xy gantry done ready to buy and print.
-
—
—
Totally new here, I've been putting together my shopping list, but in general am going to build a Eustathios based off of Jason Smith 's BOM , but hopefully with the mods Eric Lien has been working on
Totally new here, I’ve been putting together my shopping list, but in general am going to build a Eustathios based off of +Jason Smith’s BOM , but hopefully with the mods +Eric Lien has been working on. My question is, is there a service, or do any of you offer to print parts for a charge for those of us that don’t have access to a printer yet?
-
—
—
Half of misumi order arrived!! However just realized I need to tap 72 holes to M5 thread...
Half of misumi order arrived!! However just realized I need to tap 72 holes to M5 thread…
-
—
—
Originally shared by Tim Rastall Just for fun
Originally shared by Tim Rastall
-
—
—
Robotdigg.com is a good provider. Their shipping cost is huge but the arrival date is very quick
Robotdigg.com is a good provider. Their shipping cost is huge but the arrival date is very quick. Their packaging is very good as well. FedEx definitely didn’t take good care of my box but hey, everything looks tiptop.
-
—
—
Eric Lien 's V4 carriage modded for LM8UU linear bearings
+Eric Lien ‘s V4 carriage modded for LM8UU linear bearings. Printed with Carbon Fiber ABS from 3DXTech. I might do a live stream tonight with a full plate of Eustathios parts with this material.
-
—
—
Just finished building my outer frame thanks to the extrusions Paul Sieradzki sold me
Just finished building my outer frame thanks to the extrusions +Paul Sieradzki sold me.
-
—
—
Anyone make bowden clips for the kraken block?
Anyone make bowden clips for the kraken block? A pain to access in most mount designs…
-
—
—
Finally upgraded my extruder to Eric Lien 's hurcustruder
Finally upgraded my extruder to +Eric Lien’s hurcustruder. The difference is night and day! I can now start a print and leave. No fiddling with the bed to make sure the plastic doesn’t jam. Planetary stepper just powers through. I also quite like the filament spool mount. Only complaint is that it’s much harder to change the filament.
-
—
—
Yeah, it moves in all cases. I'm waiting E3D volcano :)
Yeah, it moves in all cases. I’m waiting E3D volcano :)
-
—
—
First of the many orders for a Herculein build has arrived
First of the many orders for a Herculein build has arrived. Probably a month before I get them all, but exciting none the less! I am building with one extruder, E3D Volcano 1.75 Eruption. Thanks to Filastruder for a fast delivery!
-
—
—
Hey guys, a buddy of mine let me know about this
Hey guys, a buddy of mine let me know about this. If you want a Smoothie Board check out this group buy that Arthur is doing with the Delta group. Less than 48 hours to go. I’m in for a 5x :)
-
—
—
You don't realize how big the herculien build surface is until you hold it...
You don’t realize how big the herculien build surface is until you hold it…
-
—
—
I'm thinking of using an idler to bring the belt down to the motor
I’m thinking of using an idler to bring the belt down to the motor. This will allow me to use one belt length tensioned in the xy block.
-
—
—
I aborted my built and went with the dual wire gantry, right now stuck on the drawing board somewhere
I aborted my built and went with the dual wire gantry, right now stuck on the drawing board somewhere.
-
—
—
I found an easy way to set the bar heights on Eustathios using the spacers I posted earlier
I found an easy way to set the bar heights on Eustathios using the spacers I posted earlier. Some fine tuning may be required based on the accuracy of your printed carriage or spacers as well as how the bushings (or bearings in some cases) settle in your carriage. But it gives a consistent alignment to start from.
-
—
—
A question. What should the difference in height of the two round bars be?
A question. What should the difference in height of the two round bars be?
-
—
—
all is ordered! caught a couple of quantity variances between the BOM and the breakdown of materials
all is ordered! caught a couple of quantity variances between the BOM and the breakdown of materials. now i just have to play the waiting game as all 800+ parts come from around the world. thanks for all the help!
-
—
—
I suppose this is kind of like one of these printers, a big cube
I suppose this is kind of like one of these printers, a big cube. I’m going to start with CoreXY and then if it doesn’t work how I want, i’ll move to something different.
-
—
—
Ordering my Final Parts, question regarding the silicone heater
Ordering my Final Parts, question regarding the silicone heater. Can someone send me the email of exactly what i need to tell them i need? so i can just copy and paste it in.
-
—
—
10 boxes just arrived from Misumi today
-
—
—
Almost done installing the new carriage. Plus I reprinted most if the gantry parts because I wanted better quality ones
Almost done installing the new carriage. Plus I reprinted most if the gantry parts because I wanted better quality ones. The old ones were printed on my old corexy.
-
—
—
Hey guys, what size wrench hole is needed to be drilled in the extrusions?
Hey guys, what size wrench hole is needed to be drilled in the extrusions? I measured the hole in Misumi’s cad model and its over 7mm! That seems a bit larger than the diameter of a m5 button head. I’m using OpenBuilds 2020 for this.
-
—
—
My Eustanthios build has begun! First part printed last night!
My Eustanthios build has begun! First part printed last night! +Eric Lien ‘s V4 carriage.
-
—
—
Hi, were can i find a BOM for the printed parts of the ingentis?
Hi, were can i find a BOM for the printed parts of the ingentis? How many of what part should be printed.
-
—
—
I'd like to start a discussion on the printing environment, ie
I’d like to start a discussion on the printing environment, ie. heated bed/chamber.
-
—
—
Misumi Order Placed McMaster-Carr order Placed E3D hotends and volcano upgrade order placed Printed parts in process Now is the hard part of sourcing all the other stuff
Misumi Order Placed
-
—
—
Just got the call for my glass order
Just got the call for my glass order. 420mm x 430mm 3/16” Pyrex sheet is ready for pickup. Damn that was expensive. But AWESOME!
-
—
—
My sanguinololu on my prusa i2 died!
My sanguinololu on my prusa i2 died! I can no longer print the remainder of the parts for my ingentis. After seeing the print it forward campaign I was wondering if I could hop on that list? Or if someone could just do me a big favor and print out the remainder of the parts? Any help is appreciated. I plan on starting fresh with my ingentis with a new board.
-
—
—
It never dawns on me that the Herculien is almost as big as but is only 1/3 of the price
It never dawns on me that the Herculien is almost as big as http://www.re3d.org/gigabot/ but is only 1/3 of the price. :D
-
—
—
Hey guys thanks for the add. Im currently on the planning portion of building a Herculien
Hey guys thanks for the add. Im currently on the planning portion of building a Herculien. This will be my 4th printer assembly (currently have a 3ft Kossel). I’m a little hesitant on printing the parts my self as my current printer dimensional accuracy is not that great and ABS warping is a problem since there’s no enclosure. Would anyone be able to point me to a place to get the printed parts or perhaps give me a price and print them for me?
-
—
—
business moves to the completion...
business moves to the completion…
-
—
—
Europe + 32T/10mm pulleys for the herculien Im sort of stuck here...
Europe + 32T/10mm pulleys for the herculien
-
—
—
What a difference a tap makes. I was having awful problems tapping the centre of the extrusions, the tap was getting gummed up with aluminium so I decided to treat myself to a new tap
What a difference a tap makes. I was having awful problems tapping the centre of the extrusions, the tap was getting gummed up with aluminium so I decided to treat myself to a new tap.
-
—
—
I've just about completed purchasing everything for my Eustathios build
I’ve just about completed purchasing everything for my Eustathios build. What’s left is the aluminum build/heat plate. Can someone point me the direction where I can have this custom cut to the shape of the current design? I plan on clipping a 300mmx300mm piece of borosilicate on top of it. What thickness aluminum should I go with that wouldn’t sag under ABS temps but also not take an eternity for it to get to temp?
-
—
—
So, I'm fed up with my extruder and so I thought I'd give Eric Lien 's HurcuStruder a go
So, I’m fed up with my extruder and so I thought I’d give +Eric Lien’s HurcuStruder a go. I’m a little wary of threading the main Teflon tube into a nut, so I wanted to find a way to use the push-lock solution that came with my e3d v6s. Eric’s design is really nice and allows you to easily change the attachment method. So, I quickly CAD-ed up a new attachment piece. Thought others might like to try this option, so I uploaded it here: here: https://www.dropbox.com/sh/0rifioj0v93qr86/AABfBk4VqVJRDbmDhZz_0M8Ca?dl=0
-
—
—
So I went to use my Prusa i2 yesterday and found out that the RAMPS board is no longer powering the heated bed
So I went to use my Prusa i2 yesterday and found out that the RAMPS board is no longer powering the heated bed. I have plenty of replacement boards here but instead of replacing it I think it’s about time I put my thoughts/ideas into action and build a Ingentis/HercuLien style printer.
-
—
—
Ok so after printing 2 Herculien X/Y carriages and trying to press fit the brass bushings in and destroying the carriages because I obviously tried to force the bushings too much I had an epiphany
Ok so after printing 2 Herculien X/Y carriages and trying to press fit the brass bushings in and destroying the carriages because I obviously tried to force the bushings too much I had an epiphany. I printed one more, cleaned it up a bit then put it in a vapor finishing container with some acetone just as if I was going to vapor smooth the part. When the abs was just soft enough I press fit the bushings in. Please please please correct me if I shouldn’t have done this but they lined up perfect and not they’re securely in and the part is now sitting on a piece of glass hardening again. I think the only crappy part is I put a big ol thumb print on it and smudged an edge a little but I feel like I just solved my problem in an interesting way and it looks awesome. Any feedback?
-
—
—
Hi everybody. This is probably going to seem like a lazy question, and that's because it is
Hi everybody. This is probably going to seem like a lazy question, and that’s because it is. I have the HercuLien BOM, but I don’t want to do math.
-
—
—
Finally it's (no name yet) printing. Small objects work well
Finally it’s (no name yet) printing. Small objects work well. But when is speed up or print lager objects, the filament starts slipping back while printing.
-
—
—
Here are some alignment tools I just designed and printed for when I install the new carriage on my Eustathios
Here are some alignment tools I just designed and printed for when I install the new carriage on my Eustathios. The vertical-alignment/squaring/paralleling of the components is the trickiest part if you ask me. Hopefully this can help others, and I am hoping they help me as well.
-
—
—
Anybody guess what I am printing? I also just ordered some push lock fittings to go with them (same as the ones built into e3d hot ends)
Anybody guess what I am printing? I also just ordered some push lock fittings to go with them (same as the ones built into e3d hot ends). Time to convert all my Bondtech extruders to V2 :)
-
—
—
Phew. That took a while but all the parts are ordered / claimed with respective vendors
Phew. That took a while but all the parts are ordered / claimed with respective vendors. Now I need the extrusions cut to the right length and then the
LEGOassembly begin. -
—
—
Well it is finally printing! Only one nozzle of the kraken, and I'm not buttoning up all the top and sides until it is running smooth and calibrated, but wow - After tramming and doing e-steps, first 3 test prints have come
Well it is finally printing! Only one nozzle of the kraken, and I’m not buttoning up all the top and sides until it is running smooth and calibrated, but wow -
-
—
—
To all the Eustathios builders out there
To all the Eustathios builders out there. Any of you use alternative more affordable gt2 pulleys outside of the original BoM? In particular the high torque 32t pulleys that need to be purchased from Misumi. Does it have to be 32t?
-
—
—
Eric Lien have you thought about ditching the glass bed and using a proximity sensor attached to the XY carriage for bed auto tramming?
+Eric Lien have you thought about ditching the glass bed and using a proximity sensor attached to the XY carriage for bed auto tramming? I’ve never printed directly on aluminum but my initial research turns up that it’s not bad. Just curious.
-
—
—
Anyone have a supplier that has 1/4" eccentric spacers in stock?
Anyone have a supplier that has 1/4” eccentric spacers in stock? I need 4 for my Herculien build and don’t see anyone online that has any in stock.
-
—
—
Yay, I have received the initial seed from Eric Lien .
Yay, I have received the initial seed from +Eric Lien . Putting together an order as I write this.
-
—
—
Hi all, just wanted to say how much I appreciate the work done by Tim, Jason, and Eric, as well as everyone else in the community
Hi all, just wanted to say how much I appreciate the work done by Tim, Jason, and Eric, as well as everyone else in the community. Having had the opportunity to use and assemble a few different RepRaps as well as some commercial printers, the XY-gantry style is my favorite and I really want to build a Eustathios of my own.
-
—
—
Hello, I really like the HercuLien and Eustathios but I don't want to go above a 12"x12" bed
Hello, I really like the HercuLien and Eustathios but I don’t want to go above a 12”x12” bed. What would I need to adjust/replace to scale down the build area to a 12x12 for both machines?
-
—
—
Just ordered everything from Misumi for my Herculien build....
Just ordered everything from Misumi for my Herculien build…. ooooof. :D
-
—
—
Take 2 on my New Eustathios Carriage
Take 2 on my New Eustathios Carriage. I added a shark fin tab so I could mount a connector so electrical for the carriage could be modular/removable. I did this on my last version also and it worked out well (see photos). I have 3 versions of the STL. One designed for a Molex Microfit 3.0 8pin connector, one for a PCI-E 2x4 connector (larger but easy to get an extendor cable from your local PC store), and a version just for a ziptie for those that don’t want it modular but want strain relief on the wires.
-
—
—
Anyone had a look at ? Normally I'd just dive into it, but I'm in the middle of a 10hr print and don't have the heart to cut it short
Anyone had a look at http://www.mattercontrol.com ? Normally I’d just dive into it, but I’m in the middle of a 10hr print and don’t have the heart to cut it short. I currently only use Slic3r and Cura combined with Pronterface.
-
—
—
Eric Lien you sure did design a lovely part here
+Eric Lien you sure did design a lovely part here.
-
—
—
HELP! New to the 3D printing community
HELP! New to the 3D printing community. Been doing a lot of reading and realizing that I could really get into this, have some fun, learn some stuff and hopefully contribute to the community. Not 100% sure how to get started. Currently I’m thinking that I should buy a smaller printer (was looking at a Prusa 8” i3v). Then experiment and build another. Does this make sense?
-
—
—
My bearings came in and I just test fitted them into the corner bearing brackets for my Herculien build
My bearings came in and I just test fitted them into the corner bearing brackets for my Herculien build. The fit snug in all but one of them. I’m assuming that anything short of a snug fit will result in artifacts in the prints correct? I have one corner plate where the bearing fits exactly, theres no discernable play but it comes out if I turn the plate upside down and give it a light tap.
-
—
—
On the Eustathios what is the vertical distance between the y and x axis?
On the Eustathios what is the vertical distance between the y and x axis?
-
—
—
Hi, guys. Do you think if is possible to make a belt tension table for your printers?
Hi, guys.
-
—
—
Hey. May sounds funny, but i can't figure out how to mount z axis end stop in eusthatios .
Hey. May sounds funny, but i can’t figure out how to mount z axis end stop in eusthatios . I tried and tried but can’t find the right way To Mount. May anyone can take a picture or describe it.
-
—
—
Getting close to installing my Eustathios V4 Carriage Mod
Getting close to installing my Eustathios V4 Carriage Mod. New bushings will be here Friday. Also prints with the new Bondtech Extruder Beta version are going well (closeup in the photos). I still have the tinniest z ribbing going on. But I will look into that later. The new bed supports move the bed up so it can reach the shortened height of the new carriage. Wish me luck ;)
-
—
—
Blatant abuse of community alert! With 3 more email addresses
Blatant abuse of community alert!
-
—
—
Here is the google sheet for the "Print It Forward" HercuLien / Ingentis / Eustathios plastics kit sign up list
Here is the google sheet for the “Print It Forward” HercuLien / Ingentis / Eustathios plastics kit sign up list. Pretty basic right now, but it should be fully open for editing by all now (so make it pretty if you have the skills :)
-
—
—
BTW big props to whomever made the Herculien BOM with links included
BTW big props to whomever made the Herculien BOM with links included. Made things really really easy to start chasing down parts.
-
—
—
I have enough extrusion for a 500mm cube, I have 10mm, 8mm smooth rods, I have 10mm trapezoid screws etc, I think it's time I start building
I have enough extrusion for a 500mm cube, I have 10mm, 8mm smooth rods, I have 10mm trapezoid screws etc, I think it’s time I start building.
-
—
—
I've been thinking a lot about the carriage for my printer and came across this modular design
I’ve been thinking a lot about the carriage for my printer and came across this modular design. There’s already a couple of attachments for an e3d hotend and a flexdrive direct drive.
-
—
—
And the winner is: Dat Chu I would like to thank everyone for the interest, and if for some reason I missed a name from the post it was only because If I couldn't tell explicitly that you were wanting to build, but thought
And the winner is: +Dat Chu
-
—
—
I would like to understand the timeline of these projects a bit better
I would like to understand the timeline of these projects a bit better. It looks like the Eustathios is based on the Ingentis. Is the Herculien based on these options and thus come after them?
-
—
—
Any suggestions for infill percentage when printing Herculien parts?
Any suggestions for infill percentage when printing Herculien parts? So far I’ve successfully printed the 4 corner bearing brackets and I used 100% infill but I wasn’t sure if that is overkill for those parts or any other parts. My printing profile is 4 walls, 4 layers top and 4 layers bottom then solid infill for the brackets. Normally I print bigger parts with 20-30% but for the hotend carriage I was thinking it would need to be more dense.
-
—
—
Does anyone know if the hexagon hotends will fit in the carriage without modification?
Does anyone know if the hexagon hotends will fit in the carriage without modification? (and any thoughts re hexagon vs e3d would be appreciated…)
-
—
—
Hi all. I'm new to the group and 3d printing
Hi all. I’m new to the group and 3d printing. I bought a Robo3d on the cheap and have been immediately hooked. I’m currently printing a full set of herculien parts as the RoBo was just meant to bootstrap me to a bigger printer and to have as a spare working printer should I break the herculien I’m building. Given that the robo3d is very Mendel like any tips for getting these abs parts right for the herculien. I was having delaminating issues but fixed that by slowing the print down and lowering the hot end temps but I’m still getting some warping where the bushing holes aren’t true round. I’m sorry for asking this here but the same questions in Mendel boards usually turn into “why not build a bigger Mendel?”
-
—
—
Hot off the CNC. Another pair tomorrow morning and the Y-axis can be upgraded to provide some more stiffness to the top of the machine
Hot off the CNC. Another pair tomorrow morning and the Y-axis can be upgraded to provide some more stiffness to the top of the machine.
-
—
—
Some progress pics. Unfortunately, the 10mm rods I had on hand are bent
Some progress pics.
-
—
—
I went ahead and forked the HercuLien repo to start working on docs
I went ahead and forked the HercuLien repo to start working on docs. I’ve added a tab to the BOM workbook that lists each part number and the quantity of that item needed. I organized it by type of part and aggregated the vslot components to make it easier to figure out what to order. Are you interested in pull requests for these updates?
-
—
—
Fixed the noise issues on Procerus and pushed the acceleration up to 22000 mm/s/s
Fixed the noise issues on Procerus and pushed the acceleration up to 22000 mm/s/s. Speed is set to 833mm/s.
-
—
—
Hey Everyone, I had some open printing time recently on my HercuLien and I wanted to put it to some good use
Hey Everyone, I had some open printing time recently on my HercuLien and I wanted to put it to some good use. There have been some discussions recently about improving Eustathios/Ingentis documentation (and HercuLien could use some TLC in this area also).
-
—
—
Heres a noisy video of a speed test on the Procerus I did tonight
Heres a noisy video of a speed test on the Procerus I did tonight.
-
—
—
In the vein of getting a good build guide document, I think this has some relevance: (as motivation.) Anyone could find what they need to enter this contest in our community right now....
In the vein of getting a good build guide document, I think this has some relevance:
-
—
—
Three jaw chuck, four sided extrusion....works well enough for a facing cut
Three jaw chuck, four sided extrusion….works well enough for a facing cut.
-
—
—
Showing simple one-direction cooling on an e3d hotend - images to explain something for another post
Showing simple one-direction cooling on an e3d hotend - images to explain something for another post.
-
—
—
I have been playing around with a new Eustathios Carriage
I have been playing around with a new Eustathios Carriage. I am not happy with it yet, but I wanted better cooling distribution since it is my one issue I fight right now with this printer. I wanted to get your guys input. I have printed a few prototypes to balance the discharge air around the ring. It yields great volume and distribution, but I feel I am over thinking things with the design.
-
—
—
Thanks to all who commented on cutting down the aluminium profile
Thanks to all who commented on cutting down the aluminium profile. I spent a little time squaring the blade on my chop saw (it’s an Evolution RAGE saw and went through the extrusion no problem)
-
—
—
Huh. Look at that, 301 members. Weird to think that this all started 18 months ago after ThantiK pointed me towards the T-Slot Tantillus .
Huh. Look at that, 301 members. Weird to think that this all started 18 months ago after +ThantiK pointed me towards the T-Slot Tantillus . Thanks to everyone who’s contributed so far. I’m super keen to see how the design evolves as people improve and itterate on it. Oh, and if anyone wants to produce a Eustathios build guide as they go, I may be able to arrange some sort of printer hardware/filament bounty as a reward.
-
—
—
Any advice on cutting aluminium extrusion? Bought 6 1 metre lengths off ebay now I need to cut them down to size
Any advice on cutting aluminium extrusion? Bought 6 1 metre lengths off ebay now I need to cut them down to size. Was planning on using a chop saw and a block to set the length. Thoughts?
-
—
—
Eric Lien , your initial comment about belt tension worried me a little, so I have a solution!
+Eric Lien, your initial comment about belt tension worried me a little, so I have a solution! Loosen up the bearing holders on each side slightly and pull them away from the t slot. Then attach belt and screw bearing holders back down. 😁If they slack off over time, I’ll cut off a tooth from the edge of a belt and do it again, pulling it in slightly further.
-
—
—
Few new pictures of this design I'm calling Procerus
Few new pictures of this design I’m calling Procerus. All going well so far. Initial movement tests are positive, no issues with the linked nemas and it sure is torquey. Starting on the highly experimental and untried Z axis soon, gulp.
-
—
—
Another take on the Igt/Eus motion blocks and carriage
Another take on the Igt/Eus motion blocks and carriage. I took the exact opposite approach to +ThantiK and decided to fillet almost none of the things.
-
—
—
Working on a new Ingentis/Eustathios XY carriage
Working on a new Ingentis/Eustathios XY carriage. I don’t know solidworks for crap, so I’ve been figuring it out as I’m going along. This is how far I am right now.
-
—
—
The birth of another :) Thanks to Eric Lien 's Herculien design and Nathan Buxton 's 3D prints, here are some images of my HercuLien build in progress
The birth of another #HercuLien :)
-
—
—
Just a little update to my build
Just a little update to my build. I managed to flatten the bed (hammer and beer, thanks +Eric Lien :D). The x/y mechanics is moving by steppers now but needs some calibration. next step will be to assemble z mechanics and wait for the hotends from china.
-
—
—
The birth of another :) Originally shared by Nathan Buxton Check out what I made for someone
The birth of another #HercuLien :)
-
—
—
Quick video of Techne printing snowflakes @80/100mm/s
Quick video of Techne printing snowflakes @80/100mm/s.
-
—
—
Any recommendations for where to buy geared nema17s on Aliexpress?
Any recommendations for where to buy geared nema17s on Aliexpress?
-
—
—
Aluminum extrusion is all stacked , parts are arriving, now to get down to my hackerspace and print some parts
Aluminum extrusion is all stacked , parts are arriving, now to get down to my hackerspace and print some parts.
-
—
—
PLA, 90mm/s, 240C, .8mm outer shell, .15mm layer height, 70C bed temp, - not happy about the thingiverse link :) Originally shared by Jason Smith (Birds Of Paradise FPV) So far so good
PLA, 90mm/s, 240C, .8mm outer shell, .15mm layer height, 70C bed temp, http://www.thingiverse.com/thing:264769 - not happy about the thingiverse link :)
-
—
—
Is anyone in this group at 31C3 (31
Is anyone in this group at 31C3 (31. Chaos Communication Congress) right now? May we meet today evening or tomorrow on day 4?
-
—
—
Not as fast as Shauki B , but no slouch either
Not as fast as +Shauki B, but no slouch either.
-
—
—
So what's the best source for our bed leveling springs?
So what’s the best source for our bed leveling springs?
-
—
—
Any suggestions for printer bed? I ordered a 400x360mm plate but from the ceter to the corners it is 1mm uneven
Any suggestions for printer bed? I ordered a 400x360mm plate but from the ceter to the corners it is 1mm uneven. Very bad. Now i am afraid of ordering anything new because i don’t know if i will get a even plate. I don’t want to waste more money. Milled plates are a bit expensive (in comparsion to the plate i ordered). I thought about glass. But my glass-man said it will also not be even.
-
—
—
Hello everyone, I have a question. Why Eustathios has three closed GT2 belts 1004mm, 994mm and 950mm?
Hello everyone,
-
—
—
Shared on December 25, 2014 19:55...
-
—
—
I'm just assembling the x/y-mechanics. Any tips and tricks to make it move smooth?
I’m just assembling the x/y-mechanics. Any tips and tricks to make it move smooth? There is too much tension. I nearly can’t move in x/y direction.
-
—
—
I made the expensive pulleys from by doing some rework of cheap 32T/10mm pulleys from .
I made the expensive pulleys from #misumi by doing some rework of cheap 32T/10mm pulleys from #robotdigg . I milled off the collar and drilled M3 threads between the teeth.
-
—
—
Okay, it's been long enough, here's my status update on , stay for the article, poke around for all things Metaprintr
Okay, it’s been long enough, here’s my status update on #IGentUS, stay for the article, poke around for all things Metaprintr.
-
—
—
Hey guys, sitting down to order my steppers and want your thoughts on a good choice
Hey guys, sitting down to order my steppers and want your thoughts on a good choice. Should I go 1.8 or .9 step, if I’m using a DRV8825 Stepper Driver on a RAMPS board is the .9 even necessary considering the DRV8825 does 1/32 steps. Whats the minimum power (oz/in) needed? thx
-
—
—
Finally "installed" some LEDs on the .
Finally “installed” some LEDs on the #Eustathios. By “installed”, I mean I zip-tied some Ikea dioders on…but hey, at least I don’t have to leave the light on in the room to check the prints via webcam now. Printing some bottle-openers for a few friends, since that’s what 3D-printers are made for.
-
—
—
Finally getting around to a little wiring cleanup after my 120v/800w/SSR heated bed upgrade a while back
Finally getting around to a little wiring cleanup after my 120v/800w/SSR heated bed upgrade a while back. The printed cable chain worked surprisingly well (a little dab of superlube at the link joints make the motion smooth as butter).
-
—
—
Where can i get the closed belts?
Where can i get the closed belts? Not Sdp-si (i’m from germany) and not misumi (won’t ship to private person). These are my last parts but i can’t find them anywhere. Only at misumi and sdp-si :(
-
—
—
A friend just lent me his Rigitbot
A friend just lent me his Rigitbot. Now i print the last parts for Eutathios. One step closer :) Other missing parts are hotend and heated bed. But they are on their way. I’m so exited to go on with the build next week! Might be the best christmas time ever :D
-
—
—
So for my heated bed im aiming for 330mm squared 500 watts 12v does this sound about right?
So for my heated bed im aiming for 330mm squared 500 watts 12v does this sound about right?
-
—
—
how many 90 degree brackets do I actually need for an ingentis
how many 90 degree brackets do I actually need for an ingentis. Buying 50 seems wasteful if I’m only gonna end up using 20 or so?
-
—
—
Has someone yet built a carriage for E3D and bed levelling?
Has someone yet built a carriage for E3D and bed levelling? How do you guys do Bed levelling on your Eustathios Builds? Still finishing my outer frame but yet thinking about how to best do the carriag and auto bed levelling is a must have for me.
-
—
—
I'm going to buy a heated bed from aliexpress and was wondering the exact specs this I what I'm thinking 330mm 700 watts Ac or DC not sure?
I’m going to buy a heated bed from aliexpress and was wondering the exact specs this I what I’m thinking
-
—
—
Hi all! I noticed that your machines are bigger and bigger :) but I want something smaller!
Hi all! I noticed that your machines are bigger and bigger :) but I want something smaller! e.g. 300x300x300mm external dimensions. Is it safe to scale your projects down? what I should be aware? I prefer belt version.
-
—
—
Hey! I have an e3d v5 3mm(direct drive) and I was wondering how I should go about hooking up a Bowden tube to the hotend
Hey! I have an e3d v5 3mm(direct drive) and I was wondering how I should go about hooking up a Bowden tube to the hotend. I was also wondering your favorite supplier of Bowden tube.
-
—
—
Shot glass in 3 minutes! This is about as fast as I've been able to print with the .
Shot glass in 3 minutes! This is about as fast as I’ve been able to print with the #Eustathios. I set it for a spiralized 10 sided cylinder with Cura at 200mm/s. Initial temp was 240, which was then increased to 270 mid-first layer. Layer height was .2mm. The limiting factor seems to be two-fold. The Rambo board has trouble pushing g-code fast enough if I use cylinders with a larger number of sides. At these speeds, I’m having trouble maintaining hotend temp with a 24v 14a power supply. Only downside is that I don’t think it’s a regulation shot glass.
-
—
—
Of those of you who have been using a worm drive for the Z
Of those of you who have been using a worm drive for the Z. How has that been working out, is it working with a Z lift also?
-
—
—
Finally have a moving Ingentis, just the single head at the moment to go with the Azteeg X3 Pro and RepRapDiscount Full Graphic Smart Controller
Finally have a moving Ingentis, just the single head at the moment to go with the Azteeg X3 Pro and RepRapDiscount Full Graphic Smart Controller.
-
—
—
I tried to slice the extruder head of Eustathios (v2.1, youmagine) but can't slice it correct
I tried to slice the extruder head of Eustathios (v2.1, youmagine) but can’t slice it correct. When using curaEngine, the cable tunnel is interrupted because it is solid filled between the point where it turns to the point where it reaches the splitting of the tunnel.
-
—
—
It's official. My ingentis build has begun!
It’s official. My ingentis build has begun!
-
—
—
guys my head is exploding :D to get my build started i bought a saintsmart 3dprinter kit and fried on polou and now the ramps 1.4 dont turn ANY stepper MEH :D have to figure out whats wrong...
guys my head is exploding :D to get my build started i bought a saintsmart 3dprinter kit and fried on polou and now the ramps 1.4 dont turn ANY stepper MEH :D have to figure out whats wrong… i want to build an Ingentis and what would you guys suggest as an easy and stable controller? Azteeg? Smoothie? Rambo? TinyG i see that some of you use the TinyG but on reprap i cant find a Marlin firmware? but is here a tinyG ingentis firmware available?
-
—
—
Ingentis Extruder Body V1 I suspect some of my surface quality issues come from my extruder slipping
Ingentis Extruder Body V1
-
—
—
So looking to source parts and I'm trying to determine if the parts from RobotDigg are the same as Misumi ( )
So looking to source parts and I’m trying to determine if the parts from RobotDigg http://www.robotdigg.com/product/222/GT2-Pulley-32-Teeth-8mm-Bore are the same as Misumi (http://us.misumi-ec.com/vona2/result/?Keyword=GPA32GT2060-A-P8).
-
—
—
Does anyone know a trick how to order at Misumi as an private Person?
Does anyone know a trick how to order at Misumi as an private Person?
-
—
—
Stepper / driver woes :-( How are you guys?
Stepper / driver woes :-(
-
—
—
Will this work for an ingentis?
-
—
—
Eric Lien I don't currently have a copy of Solidworks and I'm encountering some errors trying to open the .sldprt files for the drill guides in Inventor
+Eric Lien I don’t currently have a copy of Solidworks and I’m encountering some errors trying to open the .sldprt files for the drill guides in Inventor. Any chance you could provide these in .stl fomat?
-
—
—
In my quest to further lighten everything possible gantry-wise, I received a bunch of polymer bearings and CF tubes today and they are just the ticket
In my quest to further lighten everything possible gantry-wise, I received a bunch of polymer bearings and CF tubes today and they are just the ticket. Not a hint of stiction, even when you twist the bushes on the rods.
-
—
—
Tim Rastall Can I get an invite to ?
+Tim Rastall Can I get an invite to http://ingentistst.blogspot.co.nz/ ?
-
—
—
What lengths of 2020 do I need to cut for a default ingentis
What lengths of 2020 do I need to cut for a default ingentis. It doesnt mention on the Bom and Tim on YouMagine said the printer was 465 cm cubed so im assuming 445cm but i just wanna double check before I order from aliexpress
-
—
—
First moves - top "pyramid" kraken containment vessel half assembled, limit switches (except z) mounted, just need to run all the thermistor and power resistor wires, and get some longer tubing
First moves - top “pyramid” kraken containment vessel half assembled, limit switches (except z) mounted, just need to run all the thermistor and power resistor wires, and get some longer tubing. Then mount 4 extruders on the 4 sides of the pyramid, and figure out how to route the filament off a rack that will hang off the back.
-
—
—
Can I get an invite to the blog with documentation ?Trying to track down that burn-in gcode, finally got things wired up and moving!
Can I get an invite to the blog with documentation ?Trying to track down that burn-in gcode, finally got things wired up and moving!
-
—
—
So I was looking at the openbuildspartstore, and damn
So I was looking at the openbuildspartstore, and damn. T-slot is still a lot cheaper, and the price of the v-slot wheels/plates is pretty up there.
-
—
—
Hey all, just started planning my Eustathios-kinda build
Hey all,
-
—
—
On the ingentis bom for the 20 x 20 aluminum profile it says to ask for 8pieces instead of six
On the ingentis bom for the 20 x 20 aluminum profile it says to ask for 8pieces instead of six. Should I do this during checkout under the comments section or should I send the seller a message?
-
—
—
Hello there. I just started my build of Eustathios today
Hello there.
-
—
—
Fan duct, Eric Lien , or Duckface?
Fan duct, +Eric Lien, or Duckface?
-
—
—
Second question. Where can I buy a large enough heating element and it it possible to power it with a sanguinololu or would I need a relay?
Second question. Where can I buy a large enough heating element and it it possible to power it with a sanguinololu or would I need a relay?
-
—
—
So I have decided to build an ingentis
So I have decided to build an ingentis. I was wondering of there was any major performance differences between the original ingentis and it variants (herculien, eustathios, etc)
-
—
—
Originally shared by D Rob Just bought the cyclops!
Originally shared by D Rob
-
—
—
Is anyone having any black Friday deals on electronics?
Is anyone having any black Friday deals on electronics? I am just starting a eustathios build and need a full set of electronics, LCD, power supply, stepper motors, ect.
-
—
—
BigMoe I hope no one get afended when I post here since this is the closest I get to a group that post builds that can in a way reflect what I'm trying to build, and I've been following the group for a while and getting ides,
BigMoe
-
—
—
Somewhat of an odd question: I've been thinking and trying to put to digital paper a design that would use the v-slot extrusions and wheels to forgo the need for bushings/linear whatevers almost entirely and use the belt
Somewhat of an odd question: I’ve been thinking and trying to put to digital paper a design that would use the v-slot extrusions and wheels to forgo the need for bushings/linear whatevers almost entirely and use the belt system to move the v-wheel platforms along the X/Y/Z axis.
-
—
—
Guys, i'm having trouble with this printer of mine, i started building it way long before i discover the ingentis concept, i was just getting inspired by the ultimaker, lately i managed to adapt the bearing holding pieces
Guys, i’m having trouble with this printer of mine, i started building it way long before i discover the ingentis concept, i was just getting inspired by the ultimaker, lately i managed to adapt the bearing holding pieces that also carry the rods where the extruder goes.
-
—
—
After drawing the spool, I think the motor on right side can be direct drive without compromising space
After drawing the spool, I think the motor on right side can be direct drive without compromising space. The extruder will sit on this side as well.
-
—
—
Full BOM is up for HercuLien Originally shared by Eric Lien BOM is up for HercuLien
Full BOM is up for HercuLien
-
—
—
Originally shared by D Rob The Hydra with its shroudless direct bolt on fans
Originally shared by D Rob
-
—
—
Originally shared by D Rob using 1/16th micro stepping the UL-T-Slot will have 136.53 steps/mm if I use 15t g2t pulley on the motor shaft with the 32t g2t 10mm bore pulleys on the screws
Originally shared by D Rob
-
—
—
Originally shared by D Rob For everyone wanting to know how the UL-T-Slot is driven
Originally shared by D Rob
-
—
—
Originally shared by D Rob More teasers!
Originally shared by D Rob
-
—
—
Originally shared by D Rob Move along folks nothing to see here
Originally shared by D Rob
-
—
—
Originally shared by D Rob Look what the USPS fairy brought me
Originally shared by D Rob
-
—
—
Originally shared by D Rob igus Inc
Originally shared by D Rob
-
—
—
Hey all. I'm trying to put together my Eustathios shopping list, ran into this problem with the Misumi lead screws
Hey all. I’m trying to put together my Eustathios shopping list, ran into this problem with the Misumi lead screws. This line in the BOM:
-
—
—
Terje Moe, more rendering, I haven't build it yet, so technically, it just an idea
Terje Moe, more rendering, I haven’t build it yet, so technically, it just an idea.
-
—
—
Progress of my smaller Eustathios. Thanks Eric Lien for the Eustathios-spider files and Richard Horne for the Sli3DR Z axis
Progress of my smaller Eustathios. Thanks +Eric Lien for the Eustathios-spider files and +Richard Horne for the Sli3DR Z axis.
-
—
—
Sorry, the documentation page is inaccessible, how can I be invited?
Sorry, the documentation page is inaccessible, how can I be invited?
-
—
—
Speaking of bearings... I have been looking at weight reduction, both on my own (human) chassis as well as for any future printer designs (calls of 'you fat bastid' will be treated with the disdain only us cuddly types can
Speaking of bearings…
-
—
—
Guys, how many linear bearings are needed for the Eustathios?
Guys, how many linear bearings are needed for the Eustathios? The BOM says two 8mm and two 10mm, but that seems not enough? +Eric Lien, in your version, on the hotend carriage, are those linear bearings or plastic bushels? Do you have a BOM ? Thanks.
-
—
—
Greetings to all from Chile, I have a question , some of you have done this printer profiles 30x30 but what happens is that in Chile do not sell 20x20 .
Greetings to all from Chile, I have a question , some of you have done this printer profiles 30x30 but what happens is that in Chile do not sell 20x20 .
-
—
—
Controllers? I am about to buy a bunch of electronics and thought I would get some opinions
Controllers?
-
—
—
Made some adjustable feet that fit the 20 x 20 aluminum
Made some adjustable feet that fit the 20 x 20 aluminum. 5 mm bolt.
-
—
—
I was planning to build a smaller Ingentis / Eustathios with belt driven Z
I was planning to build a smaller Ingentis / Eustathios with belt driven Z. Not as small as the mini proposed by Miguel Sánchez, but housing the common MK2 heated bed. So I am really interested when Richard Horne posted the Sli3DR files.
-
—
—
Originally shared by D Rob Hail Hydra
Originally shared by D Rob
-
—
—
Being unable to work out how to embed a picture in an existing discussion, I took the easy way out...
Being unable to work out how to embed a picture in an existing discussion, I took the easy way out…
-
—
—
Just a heads up. It's out in the digital wild
Just a heads up. It’s out in the digital wild.
-
—
—
While looking around for bits I came across these little beauties - V623ZZ v-groove sealed bearings
While looking around for bits I came across these little beauties - V623ZZ v-groove sealed bearings. Only 30c each: http://www.aliexpress.com/item/10pcs-V623ZZ-V-groove-roller-wheel-ball-bearings-3-12-4-mm-embroidery-machine-pulley-bearing/32226374792.html
-
—
—
For the frame construction, is there any reason why not to use a regular Home Depot 90 degrees bracket instead of the expensive special T-Slot brackets?
For the frame construction, is there any reason why not to use a regular Home Depot 90 degrees bracket instead of the expensive special T-Slot brackets? I can buy a whole box of these for a few bucks.
-
—
—
I like the look and the idea of a Eustathios-style printer, but I live in the third world and don't have access to a 3-D printer to make parts with
I like the look and the idea of a Eustathios-style printer, but I live in the third world and don’t have access to a 3-D printer to make parts with. But I do have a bunch of 2020 and a CNC router, so I am going to look at making a variant out of various engineering components and stuff I can mill from blocks of MDF.
-
—
—
Lady's and gentlemen, I present to you my new hotend!
Lady’s and gentlemen, I present to you my new hotend! As of yet untested, but will be soon.
-
—
—
It's not quite an Ingentis, but was born from the same sort of idea - Sli3DR Source files are now up on and Github - Originally shared by Richard Horne files are all released and up on YouMagine - Enjoy another 'FreeD'
It’s not quite an Ingentis, but was born from the same sort of idea - Sli3DR Source files are now up on and Github - https://github.com/RichRap/Sli3DR
-
—
—
120v bed assembly installed. I will wire it up for the maiden voyage tomorrow
-
—
—
Hey guys, can you share some photos of your Eustathios build?
Hey guys,
-
—
—
Do you all find no issue using springs in the supports for your build platforms?
Do you all find no issue using springs in the supports for your build platforms?
-
—
—
New 380mm x 380mm (800 watt 120v) alirubber silicone heated bed with dual thermistors
New 380mm x 380mm (800 watt 120v) alirubber silicone heated bed with dual thermistors. 3/4” MDF routed insulator bottom board. 1/4” aluminum heat spreader. Omron SSR.
-
—
—
Hey all, I decided to start building a Eustathios
Hey all,
-
—
—
Hi Thinking building one of these, is there an updated BOM?
Hi
-
—
—
Here is a SSR wiring to the heated bed
Here is a SSR wiring to the heated bed. Comments?
-
—
—
Hi, Anyone knows where I could get 2020 extrusion in Canada ?
Hi,
-
—
—
I have just done the first test of my Eustathios-mini printer
I have just done the first test of my Eustathios-mini printer. I have designed the parts using OpenSCAD. Z-axis is still undefined but I might use one of the existing designs. Sources can be get from http://www.thingiverse.com/thing:513955
-
—
—
I finally got started on the Eustathios and the frame is mainly completed except that the XY axis movement still get stuck some time while moving with my hand
I finally got started on the Eustathios and the frame is mainly completed except that the XY axis movement still get stuck some time while moving with my hand. This is without the 2GT belt yet.
-
—
—
My Eustathios begins!
My Eustathios begins!
-
—
—
First World Problems: My webcam doesn't have a wide enough angle to shoot my entire build platform
First World Problems: My webcam doesn’t have a wide enough angle to shoot my entire build platform.
-
—
—
Hey all. So what is the deal with Ingentis vs Eustathios?
Hey all. So what is the deal with Ingentis vs Eustathios? I’m thinking of taking apart my Delta printer and building a Cartesian. Any tips on which model to choose? Which is more mature/robust?
-
—
—
So... Can someone help me verify the considerations necessary in firmware for x3 pro running on 24v with kraken?
So…
-
—
—
So, yesterday I had to apply excessive force to try and increase the tension in my gt2 belts, but the test circles still failed to print properly so I decided to print some of Eric Lien 's parts, after Miguel Snchez
So, yesterday I had to apply excessive force to try and increase the tension in my gt2 belts, but the test circles still failed to print properly so I decided to print some of +Eric Lien ’s parts, after +Miguel Sánchez suggested that I might have to get rid of the igus bearings. Here you can see that I just started the print, but also, that those circles suddenly look almost perfect. I may have to do some more research into what’s going on.
-
—
—
Hi guys So, I couldn't wait any longer and started printing this week even though several things are not finished yet
Hi guys
-
—
—
Jason Smith Eric Lien can I ask you guys a quick favor?
+Jason Smith +Eric Lien can I ask you guys a quick favor? You both have great carriage designs, but my printer’s got 10mm cross-beams…The Herculien just has SLDPRT’s published, and the Eustathios STL’s are sized for smaller rods.
-
—
—
Completely and totally untouched. The delta could never come close to completing this
Completely and totally untouched. The delta could never come close to completing this. It’ll be even better when I throw active cooling on it.
-
—
—
I just cannot get over how close this thing is to dialed in
I just cannot get over how close this thing is to dialed in. This is prints 6 and 7 (total, including failures to start)…6 stopped when it did because a pulley came of. (That kinda messes up the ability to restart.)
-
—
—
Had a productive day. This is print #4
Had a productive day. This is print #4. #IGentUS
-
—
—
Thank you igus Inc. for these awesome samples
Thank you +igus Inc. for these awesome samples. I will do my best to give a full and detailed review of the 1050 lead screws in the gantry of my Ul-T-Slot MKIII can’t wait to get the anti backlash screw’s as well
-
—
—
I have recently been working on devising a better way to build a z probe that works as a endstop and a auto bed levelling probe
I have recently been working on devising a better way to build a z probe that works as a endstop and a auto bed levelling probe.
-
—
—
Accomplished this weekend: Heated Bed wired to relay(I'll MOSFET-ize it later), then wiring upgraded from 16 Gauge to 12 gauge
Accomplished this weekend:
-
—
—
I finally got around to test fitting my extrusions together for my next bot
I finally got around to test fitting my extrusions together for my next bot. They are 800mm & 450mm long (Misumi HFS5-2020-800 & HFS5-2020-450). For an easy visual size comparison I put my Printrbot Plus v2 inside it.
-
—
—
Fine. Here's the Z-stage thusfar. esteps = 158.39177 Reference voltage at 1.4v (but since the motors don't move much, there's no thermal cutout and the motors don't get hot.) The drop test is with 900g worth of Chili
Fine. Here’s the Z-stage thusfar. esteps = 158.39177 Reference voltage at 1.4v (but since the motors don’t move much, there’s no thermal cutout and the motors don’t get hot.) The drop test is with 900g worth of Chili. :)
-
—
—
Hello All I'm putting out an SOS for parts print in the USA
Hello All
-
—
—
WHAT!!!!!!!!!!!!!!
-
—
—
Stepper killer is what we need!!! But man the cost Chris Purola
-
—
—
Chris Purola could this be made to work?
-
—
—
so to those who have been following me in the world of dc servo fff/fdm discovery what do you think about this approach?
DIY Servo Controller - Four Axis - PCBs so to those who have been following me in the world of dc servo fff/fdm discovery what do you think about this approach? H-Bridges are fairly cheap, but I don’t know how to implement this into current firmware and design. The H-bridge boards and encoder input ports could connect through a pololu form factor break out board and firmware could do the rest. What say you gentle men, and ladies?
-
—
—
MendelMax Mega Y axis: everyone watching and doubting the dc servo technique I'm wanting to explore check out the y on this
MendelMax Mega Y axis:
http://youtu.be/BsK9JfH_l6M everyone watching and doubting the dc servo technique I’m wanting to explore check out the y on this. Dc motor w/rotary encoder. It uses gecko drive plugged into your current electronics and firmware. The gecko reads steps/dir and handles the rest. Looking petty awesome!
-
—
—
Was helping a customer at work today and found these in my furniture catalogue
Was helping a customer at work today and found these in my furniture catalogue. They are 16inch³ outside measurements 406.4mm³. I figured there may be some interest. I can get them, for those who would like, in the 5 colors shown for $60 US plus shipping. You can drill holes you need and modify as needed. It even has a base plate already there. Just add an electronics cabinet underneath and your hardware and electronics and away you go. Easy peasy. I’m taking to you +Eric Lien, +Shauki Bagdadi, +Mike Miller, +Nuker Bot, +ThantiK, and anyone else looking for quick cheap frames.
-
—
—
Shared on October 01, 2014 04:03...
http://www.igus.eu/contentData/Product_Files/Download/mp4/Zero-Backlash-assembly_de.mp4
-
—
—
Shauki Bagdadi check this out for the 1050
+Shauki Bagdadi http://www.igus.eu/wpck/7975/Zero_Backlash_Muttern check this out for the 1050. there were none local (US)in stock so I will wait a little while for the sample. But I have 3 more 1050 lead screws and 7 regular nuts more. I will build my own spring pre-load x/y ends.
-
—
—
Thanks igus Inc. for the samples it appears the 10mm with 50mm pitch may be just what x/y for the Ul-T-Slot needs
Thanks +igus Inc. for the samples it appears the 10mm with 50mm pitch may be just what x/y for the Ul-T-Slot needs. I will also try out these other samples and share my results.
-
—
—
Hello all I am new and have a question
Hello all
-
—
—
Eric Lien 's v3 Extruder print from cura 14.07....
+Eric Lien’s v3 Extruder print from cura 14.07…. support from bed… 50mm/sec .03 layer height 2mm shell thickness fill Densitiy 20% 3mm E3D v6 direct drive with seemecnc ezstruder (direct drive) so damn tuned that support gently pulls off like +Simplify3D minus the price tag…. (btw +Simplify3D I will do a free review against the free products I use if you provide me with a free license of your paid product. )
-
—
—
Alright, you've waited long enough is officially a plotter
Alright, you’ve waited long enough #IGentUS is officially a plotter. Using +MISUMI USA extrusions and +igus Inc. #Drylin bushings, it’s making lines and turning circles.
-
—
—
Z-motor mount: I'd like two motors down there, where can I find the printed bracket?
Z-motor mount: I’d like two motors down there, where can I find the printed bracket? Its not on the youmagine site, and the one I have was printed by someone else.
-
—
—
My solution for a dropping bed. 1:10 worm gear, with a 5mm stainless rod that goes across the entire bed
My solution for a dropping bed. 1:10 worm gear, with a 5mm stainless rod that goes across the entire bed. Keeps everything in sync, no lash (though it took quite a few adjustments and prints to get it that way!), 1 motor, and I can flip it and hide it away under the machine once I extend it.
-
—
—
Techne build pics and first few prints :-D
Techne build pics and first few prints
-
—
—
I have been away for SOOO long, I just started working at a new company in Australia making 3d printers (3D industries)
I have been away for SOOO long, I just started working at a new company in Australia making 3d printers (3D industries). That, my new house and my ingentis / eustathios mash up “Techne” have taken up so much time I’ve simply not checked my G+ for months!
-
—
—
So... if there is anyone out there willing to help me unravel the mysteries of dc motors w/ optical rotary encoders, for ingentis variants, my research has led me here
So… if there is anyone out there willing to help me unravel the mysteries of dc motors w/ optical rotary encoders, for ingentis variants, my research has led me here. I state once again that I suck with the arduino coding. I believe this is the next logical step in 3d printing. DC motors are faster lighter and cheaper. The encoders are cheap and easy to salvage as are the motors (2d printers). 2d printers moved to this tech while gaining resolution and cutting costs. HELP ME!!! I can figure out the circuitry necessary and the microcontroller hook ups to make it work. I haven’t the foggiest on how to make it play nice with current boards though; which is a must to make this viable.
-
—
—
Shared on September 23, 2014 05:01...
D Rob
-
—
—
K so I found this. Kan someone help me figure out how to apply this to the current generation of 3d printer electronics?
https://github.com/danithebest91/ServoStrap/blob/master/Arduino_stepper_motor_emulator_v1.0.1_direct_port_manipulation.pde K so I found this. Kan someone help me figure out how to apply this to the current generation of 3d printer electronics? ramps or ultiboard, or marlin in general. I am trying, but my arduino programming skills are non existent!
-
—
—
I want to incorporate this dc motor technique for my UL-T-SLOT Mk.III
http://www.3ders.org/articles/20140116-dc-motor-powered-rapy-3d-printer-made-in-korea.html I want to incorporate this dc motor technique for my UL-T-SLOT Mk.III. Can someone help me in the right direction. I will use a stepper motor for z still, but I can’t code for crap, and firmware mods will definitely be needed. This change will help people be able to salvage motors from 2D printers to build 3D printers too.
-
—
—
I present to you the UL-T-SLOT MKIII, the top secret project I've been working on
I present to you the UL-T-SLOT MKIII, the top secret project I’ve been working on. Still have to hook up electronics and flash firmware. And finish the custom hotend I’m working on… (Hail Hydra!).
-
—
—
I think I've got the Falling Z-stage issue licked!
I think I’ve got the Falling Z-stage issue licked! I figured what the problem needed was a clutch or brake, but couldn’t figure out the easiest way to do so. Playing about with a bit of GT2 belt, I recalled a mechanism that would drag in one direction only, because it had a spring on a belt that was only pulled tight in one direction. Looking at the video, I plan to have a mount with two springs, tension for raising and lowering the bed.
-
—
—
Idler designs .5, 1 and 2...I'll incorporate guides and call it done
Idler designs .5, 1 and 2…I’ll incorporate guides and call it done.
-
—
—
anyone using a single e3d v6 on their ingentis?
anyone using a single e3d v6 on their ingentis? if so toss me and stl…not that I’m too lazy to design one. But right now is past time to plant for a good winter crop and i’m about two weeks behind. That’s not including a deer plot. (for those that are confused, I have a veggie garden and hunt deer during the winter) Thanks in advance!
-
—
—
Going through the BOM, is there any reason it includes the GT2 pulleys from Misumi when there are similar ones on robot dig for a fraction of the price?
Going through the BOM, is there any reason it includes the GT2 pulleys from Misumi when there are similar ones on robot dig for a fraction of the price?
-
—
—
Is there a build guide for Ingentius?
Is there a build guide for Ingentius? I’m interested in building one.
-
—
—
So I've finally got some time to start my Eustathios build and need to start putting all the parts together
So I’ve finally got some time to start my Eustathios build and need to start putting all the parts together. Couple of questions for those of you who have already built yours.
-
—
—
My printer finished it's longest print so to celebrate i printed a .5 scale of the gear bearing
My printer finished it’s longest print so to celebrate i printed a .5 scale of the gear bearing.
-
—
—
Since i have converted to belts i had to give the Prusa mendel i2 a workout tonight
Since i have converted to belts i had to give the Prusa mendel i2 a workout tonight. 3 1/2 hr print replacing the +Tim Rastall bearing brackets with a modified +Eric Lien bearing block. Also I’m using the motor Mount that +Brian Bland sent me to have direct drive. It’s slowly getting together
-
—
—
I haven't posted in a while. Thought I would share my Iteration Bin
I haven’t posted in a while. Thought I would share my Iteration Bin. Some are items I should have measured twice printed once, some are design changes based on how it performed, and some are the change from corexy to #HercuLien. But all of them are a learning experience.
-
—
—
GT2 questions I've got movement (not ready for video yet)
GT2 questions
-
—
—
I'm changing my Prusa mendel i2 (first printer) with a refresh of a Prusa_i3_rework
I’m changing my Prusa mendel i2 (first printer) with a refresh of a Prusa_i3_rework. All new frame and parts and only keeping the electronics and some smooth rods. This is the first part printed with my Eustathios variant: red ABS, H:240C, B:110C, 1hour to print.
-
—
—
Dialing in on to find the optimal printing settings
Dialing in on #HercuLien to find the optimal printing settings. Batman was printed in ABS at 60mm/s, Octopus was in PLA at 70mm/s but extrusion was off slightly, and the green lifting bracket foundry pattern was for work and printed in PLA at 40mm/s. The bracket pattern mounts to a molding plate and becomes the mold positive for greensand ductile iron casting. The feed riser was printed integral to the part. The pattern is about 11” across, and after some priming, sanding, and high build pattern paint the impression was glass smooth.
-
—
—
First print off the Ingentis/Eustathios. Turned out pretty good I think
First print off the Ingentis/Eustathios. Turned out pretty good I think. Still need to figure out print speeds with it.
-
—
—
Z Max is down. Giving some thought to endstops
Z Max is down.
-
—
—
My baby's first steps... I couldn't be more proud
My baby’s first steps… I couldn’t be more proud.
-
—
—
Latest prints from HercuLien. First was a car for my boys to test the centrifugal blowers on small features in PLA at medium speeds
Latest prints from HercuLien. First was a car for my boys to test the centrifugal blowers on small features in PLA at medium speeds. Then some Lego’s to test tolerances. And now I have a larger piece for work. It is the cope half of a foundry pattern with the riser printed integrally.
-
—
—
Testing 50x50x15mm blower fan as a replacement of my current axial fan system on .
Testing 50x50x15mm blower fan as a replacement of my current axial fan system on #HercuLien. So far I like it much more. Way more airflow, and higher velocity. Time to build a better mount and design a small directed duct.
-
—
—
Test fitting the prototype On-Carriage-Direct-Drive modular extruder for .
Test fitting the prototype On-Carriage-Direct-Drive modular extruder for #HercuLien. I know it’s ugly and I have still not figured out my on-carriage wire management scheme. But it should be perfectly functional and open up #Herculien for additional filaments not ideal for Bowden applications.
-
—
—
First test piece for in carriage direct drive extruder module for the HercuLien
First test piece for in carriage direct drive extruder module for the HercuLien.
-
—
—
HercuLien first test prints. Calibration is needed...
HercuLien first test prints. Calibration is needed… But a good start.
-
—
—
Progress Update Defcon sucked away a week of my life (but was so SO worth it), and I'm at the point in the build where things are happening, but don't APPEAR to be happening
Progress Update
-
—
—
How much does an ingentis cost you from aliexpress?
How much does an ingentis cost you from aliexpress? Particularly, how much does 2020 extrusion and fasteners add to the price? +Tim Rastall
-
—
—
I finished assembly and wiring of late last night
I finished assembly and wiring of #HercuLien late last night. Here are some pictures. I am really happy with the precision feel on the gantry motion, the total lack of friction when moving the gantry by hand, and the package as a whole. The only thing remaining mechanically is the new side panels.
-
—
—
It's late and I'm tired. But tomorrow will likely be the day HercuLien makes its first movements
It’s late and I’m tired. But tomorrow will likely be the day HercuLien makes its first movements.
-
—
—
Hi, i would like to purchase a good nema 17 motor, but I want one with 40mm length like ultimaker motors
Hi, i would like to purchase a good nema 17 motor, but I want one with 40mm length like ultimaker motors. Does anyone recommend a seller for me?
-
—
—
So, it's finally printing! Ran into some issues with the extruder calibration
So, it’s finally printing! Ran into some issues with the extruder calibration. Thought I had done it right and got 222 steps/mm. Turns out this was way off, causing the extruder to skip steps and allowing the filament to retract suddenly. Did a bit of math, figured out I was off, and then re-calibrated correctly (This time, not actually pushing the plastic through the hotend). Working beautifully now at 189steps/mm.
-
—
—
HercuLien is getting closer. Once I finish wiring and troubleshooting I'll be releasing the Solidworks assembly source files out on github with the rest of my other projects
HercuLien is getting closer. Once I finish wiring and troubleshooting I’ll be releasing the Solidworks assembly source files out on github with the rest of my other projects.
-
—
—
How many of each printed part do I need for Ingentis?
How many of each printed part do I need for Ingentis?
-
—
—
I have a 300x300x6 mm piece of borosilicate?
I have a 300x300x6 mm piece of borosilicate? glass from a broken bathroom scale that I am thinking of using as a print surface/bed.
-
—
—
Originally shared by Farnell element14 MIT students modify a 3D printer with a height-measuring laser
Originally shared by Farnell element14
-
—
—
So, as some of you predicted, my Z-axis is giving me hell
So, as some of you predicted, my Z-axis is giving me hell. The lead screws will randomly bind up at certain places along the screw and the steppers will make a god-awful noise. Sometimes, once the motors stop, it’ll unbind enough to travel again if I tell it to. Other times, it’s just stuck. I tried shortening the center aluminum extrusion on the bed assembly as I determined it was a bit long for the spacing of the 2 z-steppers, but it only helped a bit. It still gets stuck now and then. I’ve gotten it to home maybe twice without it binding up.
-
—
—
I am working on a bowden extruder to replace the PlanetCNC Airtripper variant I have been using
I am working on a bowden extruder to replace the PlanetCNC Airtripper variant I have been using.
-
—
—
Ordered on Monday Delivered on Thursday! was a bargin!
Ordered on Monday Delivered on Thursday! trimcraftaviationrc.com was a bargin! Thanks +Brian Bland for telling me about them.
-
—
—
LoboCNC's approach.: only one belt and rod per axis Yes it's more simple but what about vibrations when rolling...
LoboCNC’s approach.: only one belt and rod per axis http://forums.reprap.org/read.php?1,386926 Yes it’s more simple but what about vibrations when rolling…
-
—
—
Anthony White , here's a close up
+Anthony White, here’s a close up.
-
—
—
Anthony White Here is a picture. Should show what you need to know
+Anthony White Here is a picture. Should show what you need to know.
-
—
—
Ok - what am I screwing up here?
Ok - what am I screwing up here? The belt can slot nicely in on one end, but how is the other end then attached?
-
—
—
How are you guys dealing with the press-fit aspect of Igus sleeve bushings and do you have problems hitting the target tolerances in your plastic parts?
How are you guys dealing with the press-fit aspect of Igus sleeve bushings and do you have problems hitting the target tolerances in your plastic parts?
-
—
—
Status update: My printer now has a 'Front' And I've discovered that it's much stiffer in one direction (constrained by Cap screws threaded into the 20x20) than the other (constrained by printed 90 degree retainers)
Status update: My printer now has a ‘Front’
-
—
—
Update on my "Big Bot" conversion from CoreXY to Ingentis/Eustathios
Update on my “Big Bot” conversion from CoreXY to Ingentis/Eustathios. I now know how to use loft and guide curves better in solidworks which is fun. It is a really great way to make more organic shapes… but keep Solidworks happy with fully defined geometry. I also learned some more tricks from our design engineer at the foundry about drawing in assembly for part placement. I would have never been able to define the duct mounting/pivot tab easily without this (since the tab sits at a compound angle).
-
—
—
Could somebody give me ballpark numbers for the max Z speed on the belt drive?
Could somebody give me ballpark numbers for the max Z speed on the belt drive? And is there backlash?
-
—
—
Second version of the carriage for the Kraken
Second version of the carriage for the Kraken. Centered on the rods better and this one will let the Kraken actually touch the build surface. These prints were sliced with CraftWare software. CraftWare lets you modify support similar to Simplify3D.
-
—
—
The first automated moves on my new printer, which I am calling "Machigai" .
The first automated moves on my new printer, which I am calling “Machigai” . Machigai is Japanese for “Mistake”, as I have made many during the design of this printer. The frame and basic design is from the Ingentis, but I am using linear rails for all axes. Inspiration was taken from many places to design the mounts, but they are of my own design, so when they fail, I have no one else to blame.
-
—
—
A little further progress on the carriage design
A little further progress on the carriage design. Front clamp/fan-mount works great. I will be adding some directional ducts that mate the outlet of the fan to the heat sink later. Also I still need to design the part fan ducts. But it’s getting closer.
-
—
—
First attempt at the dual extrusion carriage design for my conversion from Corexy to Ingentis/Eustathios
First attempt at the dual extrusion carriage design for my conversion from Corexy to Ingentis/Eustathios. The frame is 24” x24” x24” and it will be called the HercuLien thanks to a suggestion from +Shauki Bagdadi. The flat top and lots of mount holes are to allow for mounting a direct drive extruder on top in case I want to run flexible filaments. The mounting tabs on the back will allow for adjusting ducted cooling fans for PLA. Heat sink cooling will be done with 40mm fan(s) that mount to the hot end front clamp. I have not yet drawn up the clamp or fan ducts. I plan on learning more about surfacing and loft/sweep in solidworks to make these parts.
-
—
—
Laser cut option? .... So I have a big laser cutter (1200 x 960 table) and would like to know if anyone has some ideas on converting this into a laser cut version, I have a bunch of 6mm hardwood marine ply to use (and 4mm if
Laser cut option? ….
-
—
—
Have not found an extruder that I am happy with, so I modified parts
Have not found an extruder that I am happy with, so I modified parts. I am getting closer just have to figure out the best way to mount it to the frame. I also like the direct drive steppers better than the belt drive.
-
—
—
Modeling the conversion of my CoreXY to a large Eustathios/Ingentis is coming along nicely
Modeling the conversion of my CoreXY to a large Eustathios/Ingentis is coming along nicely.
-
—
—
Hi, If I could pick your brains for a moment, I 'm having trouble printing on my latest printer..
Hi, If I could pick your brains for a moment, I ‘m having trouble printing on my latest printer.. (ingentis / Eustathios / rigidbot). On the photo, i’ve done a torture test. On the left, my old trusty Prusa I2 /w direct drive filament. On the right, my clone using bowden and airtripper’s extruder. both have the same setting to print out. 80mm/s with 205C temp. they both have a J-head (the prusa has a brass ending while the clone has a aluminium one). both tests were made witht the same spool.. Has you can see, the clonde is having trouble printing.
-
—
—
Let me try this video again
Let me try this video again.
-
—
—
I am looking for a Thrust bearing that I can just bolt on to T-Slot extrusion for my ingentis/eustathios
I am looking for a Thrust bearing that I can just bolt on to T-Slot extrusion for my ingentis/eustathios. I would like to get it through Ali-Express but I don’t know what to search for. Every time I look through Ali-Express I get a million results and get frustrated trawling through the results. Anyone have any tips. I plan on getting some of these for my z and have the ends turned to match thrust bearings and gt2 pulleys.
-
—
—
Originally shared by Brandon Satterfield Productive Saturday!
Originally shared by Brandon Satterfield
-
—
—
igus Inc. Cheap Friction Fit: I needed to adapt the igus polymer bearings (AWM-10) to the ingentis printed parts
+igus Inc. Cheap Friction Fit:
-
—
—
The carriage in question looked something like this...the block on the right is the 40mm fan to cool the e3d, the block you can see on the back left was for part cooling, and each bearing surface was supported by two bushings
The carriage in question looked something like this…the block on the right is the 40mm fan to cool the e3d, the block you can see on the back left was for part cooling, and each bearing surface was supported by two bushings.
-
—
—
What about scaling UM2 Z stage? Stock variant is 4mm plate ( MIC6?) and two flange linear bearins LM12LUU - 57mm long
What about scaling UM2 Z stage? Stock variant is 4mm plate ( MIC6?) and two flange linear bearins LM12LUU - 57mm long. So the base is 57mm for 200x200mm. For 400x400 bed we can double base using a pair of bearings for each Z rod and some rigit frame for bed. It makes the whole printer taller for about 10cm but more simple.
-
—
—
Aquarium airpump is great for cooling. I think Schorsch printer uses it too
Aquarium airpump is great for cooling. I think Schorsch printer uses it too https://pp.vk.me/c620323/v620323705/c873/xirxVrIIjc4.jpg
-
—
—
I haven't been paying attention...there's a gantry that's used with a v5 e3d, and has two fans for the hot end and the part being printed, I've seen it on one of out Ingent/Eust/Quad/Things, but I've never seen a link to an
I haven’t been paying attention…there’s a gantry that’s used with a v5 e3d, and has two fans for the hot end and the part being printed, I’ve seen it on one of out Ingent/Eust/Quad/Things, but I’ve never seen a link to an STL
-
—
—
So, this is my third printer. Its a mix of Ingentis> bed setup and <Eustathios/ultimaker> > X/Y axis and Rigidbot > frame tubing and printed parts
So, this is my third printer. Its a mix of Ingentis> bed setup and <Eustathios/ultimaker> > X/Y axis and Rigidbot > frame tubing and printed parts. A short vid while printing a part @ 100mm/s. Tell me what you think ;-)
-
—
—
I'm giddy with anticipation! A Box came in the mail and it lets me introduce to you the latest build project
I’m giddy with anticipation! A Box came in the mail and it lets me introduce to you the latest build project. My printer has a name:
-
—
—
My printer with kracken installed
My printer with kracken installed.
-
—
—
Z stepper motor connectors. The Printxel wires its two Z stepper motors in series rather than the more typical parallel Z stepper wiring
Z stepper motor connectors.
-
—
—
So is this the proper wiring to incorporate dual motors in a dual motor axis?
So is this the proper wiring to incorporate dual motors in a dual motor axis? (Something seems missing…)
-
—
—
So is there any reason why drill rod and polymer igus bearings would be a a really bad plan for a Eustathios build?
So is there any reason why drill rod and polymer igus bearings would be a a really bad plan for a Eustathios build? I ask because I have loads of bearings and 3/8 drill rod that Im not going to use.
-
—
—
THESE THINGS!
THESE THINGS!
-
—
—
First steps in converting my 24" x24" x24" frame corexy into ...
First steps in converting my 24” x24” x24” frame corexy into … Megagentis … Megathios… Megalien? Name still needs work. I will give more updates as I get further along. Name suggestions welcome.
-
—
—
Hi, I'm new to the group. I've built a Ingentis/Eustathios/rigidbot variant (i'll post pictures later) and I have a question about calculating steps for a belt driven z-axis bed..
Hi, I’m new to the group. I’ve built a Ingentis/Eustathios/rigidbot variant (i’ll post pictures later) and I have a question about calculating steps for a belt driven z-axis bed.. how did you guys do it ? I have a 1.8 degrees nema17 motor with a 36 tooth gear connected on a 90 tooth pulley that drives a 8mm shaft that have the belts on the end (they’re each on a 36 tooth/8mm bore). i’m look for the formula that can give me the number I can put in the marlin firmware for the steps.
-
—
—
It's at this point I ran out of washers....further movement will have to keep til I return from vacation
It’s at this point I ran out of washers….further movement will have to keep til I return from vacation. (Like my High-Zoot Carbon Fiber mock-up bearings?)
-
—
—
Speaking of collecting parts... I bought my bearings from Fast Eddy, as per the Eustathios BOM, and they sent me a 15% discount code to share with all the other people collecting parts :)
Speaking of collecting parts… I bought my bearings from Fast Eddy, as per the Eustathios BOM, and they sent me a 15% discount code to share with all the other people collecting parts :)
-
—
—
Collecting...collecting....collecting.... (and yeah, the diamond-plate won't be structural...or, sadly, mostly visible
Collecting…collecting….collecting…. (and yeah, the diamond-plate won’t be structural…or, sadly, mostly visible. It’ll be between the built frame, a layer of cork, a heated bed, and a glass build surface. 12”x12”
-
—
—
Any suggestions for a good source of spectra line?
Any suggestions for a good source of spectra line? Also, typical specs for use in a reprap?
-
—
—
Hey guys! Just signed up here after Tim invited me
Hey guys!
-
—
—
D Rob , and all others responsible, Thanks
+D Rob , and all others responsible, Thanks. I ordered the 32 tooth 10mm pulleys from robotdigg 5 days ago, and I have them already :)
-
—
—
Besides Anthony Morris , anyone else doing a kraken build?
Besides +Anthony Morris, anyone else doing a kraken build? I got my lm8u bearings in from the BOM, but realize the previously posted kraken mount probably is sized for brass bushings no? Should I order them or modify the carriage design? I only have the two lm8uus…..
-
—
—
Sorry wrong link guys
Sorry wrong link guys.
-
—
—
So not exactly 3d printing but I thought I would share with you guys
So not exactly 3d printing but I thought I would share with you guys. This is an example of the UI (IN BROWSER) called chillipeppr using #TinyG (full disclosure I am one of the #tinyg creators) and how easy it is to extend it! TinyG is coming to a 3d printer near you very soon. However this is going to be a really good talk and I think everyone will pick up something from it. So its short notice (2 mins!) but if you have some time on a lazy Sunday give it a go!
-
—
—
Hey people, does someone have a rough estimate on the cost of mechanical parts of the Eustathios?
Hey people,
-
—
—
Endstops seem optional these days. I'm seeing several of you with moving printers with no real endstops in sight
Endstops seem optional these days.
-
—
—
Hey everybody. I was wondering if the g3d smart lcd controllers work with the azteeg x3 v2
Hey everybody. I was wondering if the g3d smart lcd controllers work with the azteeg x3 v2. Or what lcd controller is good for it?
-
—
—
Lately has been skipping a beat for me
Lately #simplfy3d has been skipping a beat for me. First time the Z steps were off, a 20mm cube came out 24mm tall now the extruder is spinning about 300 mph and shredding the filament. If i do a extruder calibration of 50mm it is correct but then slice and print, not good. If i slice in Cura then print in S3D it is fine for some reason it has been changing the EEPROM, i guess. This is happening on 2 printers not just one. Kinda irritated $140 and all.
-
—
—
Eustathios / Ingentis taking shape (kraken mounting is next, starting design of acrylic 4 walls and pyramidal top)
Eustathios / Ingentis taking shape (kraken mounting is next, starting design of acrylic 4 walls and pyramidal top)
-
—
—
iGlidur questions: I've got a mass of Ingentis parts printed and ready for assembly
iGlidur questions: I’ve got a mass of Ingentis parts printed and ready for assembly. At the time I was leaning towards a bushing solution, but +Shauki Bagdadi’s experience with iglidur parts interests me…problem being I’ve got parts with a 15.4mm opening, and the nearest iglidur part is 14mm in diameter…thoughts on how to properly solve that difference in diameter? (It’s near enough to 5/8” that I think that was the desired dimension in the plans….which doesn’t seem to make sense with 8mm and 12mm shafts…)
-
—
—
This is Sli3DR (Slider) - part of the family - My Ingentis/Tantillus inspired design is finished and working well
This is Sli3DR (Slider) - part of the #RepRapMy #3DR family - My Ingentis/Tantillus inspired design is finished and working well.
-
—
—
So I got the XY gantry of my modded Eustathios assembled today
So I got the XY gantry of my modded Eustathios assembled today. Things are beginning to move pretty quickly now that I have nearly all the parts.
-
—
—
I was wondering how to scale the Ingentis form factor as straight outer shafts become almost exponentially more expensive the longer they get
I was wondering how to scale the Ingentis form factor as straight outer shafts become almost exponentially more expensive the longer they get. This is one of a number of ideas I have to get around it. The horizontal extrusion is vslot. Thought +Shauki Bagdadi might like it particularly. KISS Kim!
-
—
—
Hey folks. Just edited the community title to include the Eustathios, given the excellent work Eric Lien , Jason Smith and Riley Porter have done on the Eustathios and it's design files
Hey folks. Just edited the community title to include the Eustathios, given the excellent work +Eric Lien , +Jason Smith and +Riley Porter have done on the Eustathios and it’s design files. All three promoted to owner status accordingly :)
-
—
—
Hey guys where is the best place to pickup the self aligning bearings now?
Hey guys where is the best place to pickup the self aligning bearings now? Last time I ordered from SPD-SI they charged me like 20$ shipping for 10 bearings, I wasn’t a fan. lol
-
—
—
Corner pieces: I'm still wrapping my head around the whole 'You've got a printer , print what you need!'
Corner pieces:
-
—
—
Anthony White This should help regarding your previous posts
+Anthony White This should help regarding your previous posts.
-
—
—
So I have the parts for the gantry ready to go, and seem to remember reading about a technique of spinning the shaft in the bushings with a drill in order to align them properly
So I have the parts for the gantry ready to go, and seem to remember reading about a technique of spinning the shaft in the bushings with a drill in order to align them properly. Anyone know of either the post or the technique I’m thinking of? However, my prints for carriage and the x/y axis supports seem a bit of a tight fit with the bushings - worth reprinting tweaked to get the measured diameter found in the part file? Or sanding it out a bit to fit? Or heating the bushing and press fitting in somehow?
-
—
—
Direct coupled motor mount. It doesn't look very strong but it sure is
Direct coupled motor mount. It doesn’t look very strong but it sure is.
-
—
—
Spool holder installed and a mount for the webcam to use with octoprint
Spool holder installed and a mount for the webcam to use with octoprint. Man I love octoprint. Webcam is a Logitech C270 which I disassembled to adjust the lense focal ring better for the distance to the center of the bed. I unscrewed and pulled off the standard monitor mount for space savings.
-
—
—
The gear bearing print has always eluded me on my corexy
The gear bearing print has always eluded me on my corexy. Printed first try on the Eustathios. I have said it before but I will say it again: thanks +Tim Rastall and +Jason Smith. This printer is amazing.
-
—
—
Fine detail is much easier on the Eustathios than it was with my corexy
Fine detail is much easier on the Eustathios than it was with my corexy. Man I love this printer. Printed in PLA at 190c with 0.4mm E3D v6. Left to right:
-
—
—
Not a bad start :)
Not a bad start :)
-
—
—
Almost ready to testfire the Eustathios. I am just reprinting the new extruder carriage for my design that uses a 40mm fan for cooling my e3d v6 heat sink, and another 40mm fan for cooling the part
Almost ready to testfire the Eustathios. I am just reprinting the new extruder carriage for my design that uses a 40mm fan for cooling my e3d v6 heat sink, and another 40mm fan for cooling the part.
-
—
—
Hi guys Im building a printer similar to the Ingentis/Eustathios, but using OpenBeam (only extrusions I could find in South Africa when I started the project)
Hi guys
-
—
—
Getting closer to printing everyday
Getting closer to printing everyday.
-
—
—
Originally shared by Brian Bland Here are the files for the Ingentis Kraken mount
Originally shared by Brian Bland
-
—
—
Bicycle Chain Z-lift? I'm pitching one of my kid's crappy Walmart bikes and am looking to recycle any parts possible and come to the chain
Bicycle Chain Z-lift?
-
—
—
I want these... but for the ingentis
I want these… but for the ingentis. I’m guessing that the hot end mount would have to be redesigned for different cross bar positioning though. :[
-
—
—
Electronics tray for the Eustathios I should be finishing up this weekend
Electronics tray for the Eustathios I should be finishing up this weekend. MAN steppers take a long time to get to the states via China Post. But that’s OK. I got to spend more time modeling little tweaks like this.
-
—
—
There is a fine line between to much friction, nice sliding movement and slop
There is a fine line between to much friction, nice sliding movement and slop.
-
—
—
Did a little modification to my heater blocks today
Did a little modification to my heater blocks today.
-
—
—
I am working on building my new printer and need a recommendation
I am working on building my new printer and need a recommendation. I have only worked with 3mm filament and direct drive extruder. My new printer will use 1.75 and bowden extruder. Any recommendations on extruder (cold end) designs I should check out?
-
—
—
A couple of pics. Mounting the X-Y steppers below in the electronics area will allow open ended belts to be used
A couple of pics. Mounting the X-Y steppers below in the electronics area will allow open ended belts to be used. Also a pic of the Kraken carriage. Still not happy with it.
-
—
—
I am interested in building an ingentis printer
I am interested in building an ingentis printer. I already built a prusa i2 however I find the build volume limiting and the frame too unstable for really nice prints. I was wondering if you guys could give me your honest opinion on both the ingentis and the Eustathios printer. Also which of the two is cheaper and which is the most reliable.
-
—
—
Bijil Baji Jason Smith I think this is what you were after
+Bijil Baji +Jason Smith
-
—
—
Hello Guys i am thinking of making an Eustahios printer i have aluminum extrusion of below given specs would it be strong if i make cornor joints with laser cut acrylic instead of printed parts
Hello Guys i am thinking of making an Eustahios printer i have aluminum extrusion of below given specs would it be strong if i make cornor joints with laser cut acrylic instead of printed parts
-
—
—
Printed a whole set of new XY ends for another .
Printed a whole set of new XY ends for another #Eustathios . Need to get a higher quality webcam :(
-
—
—
Originally shared by D Rob
Originally shared by D Rob
-
—
—
I have modified the Z axis to use more standard (Though not completely standard) hardware
I have modified the #Eustathios Z axis to use more standard (Though not completely standard) hardware. I decided I’d take the time to CAD up my Z-axis modification to make sure everything fits (It does!). I’ve decided to center the lead screw and double the smooth rods to 2 on each side for extra rigidity. I’ve also gone with 2 steppers as it will allow me to simply attach the lead screws directly with a coupling. Any thoughts or issues?
-
—
—
Printing some new bearing holders for a buddy at 100mm/s
Printing some new #Eustathios bearing holders for a buddy at 100mm/s.
-
—
—
Assuming I've set up permissions correctly, there are a number of Ingentis files in this folder
Assuming I’ve set up permissions correctly, there are a number of Ingentis files in this folder. Either IGES, STEP or both. One is the default Ingentis with mk1 Kraken carriage the other is the belt drive version with redesigned xy ends (that should work with both spectra and belts) and an lm8uu dual hotend carriage. The carriage and xy ends have not been tested yet!
-
—
—
Hi Folks. Just wanted to apologise for making promises to share files or designs and then failing to do so - I'm super busy at work right now and I had my CAD PC died so I couldn't get Rhino fired up to export the relevant
Hi Folks. Just wanted to apologise for making promises to share files or designs and then failing to do so - I’m super busy at work right now and I had my CAD PC died so I couldn’t get Rhino fired up to export the relevant files. I’ve invested in a grunty 15” Macbook pro with VMware so I’ve got Rhino going again. As soon as I get the chance I’ll export all of my finished or work in progress designs to IGES/STEP and put them on Google drive.
-
—
—
Eric Lien , Here are the pics of the Z-axis thrust bearings/collars, bed level springs, and single-extruder carriage
+Eric Lien, Here are the pics of the #Eustathios Z-axis thrust bearings/collars, bed level springs, and single-extruder carriage. Keep us posted as you finalize your build!
-
—
—
Eustathios build getting closer. I am calling it the Eustathios "Spider" due to the color scheme and a few design items I am still working on
Eustathios build getting closer. I am calling it the Eustathios “Spider” due to the color scheme and a few design items I am still working on.
-
—
—
Slight delay in my build due to changes in the Kraken
Slight delay in my build due to changes in the Kraken. Can’t use +Tim Rastall carriage. Mounting holes are 1mm farther apart in the longer direction and the coolant barbs are closer together so the hoses would rub on the x shaft.
-
—
—
These 7075 Aluminium eustathios pillow blocks should be nice and rigid, yeah?
These 7075 Aluminium eustathios pillow blocks should be nice and rigid, yeah? :-)
-
—
—
Anyone got 145 bucks burning a hole in their pocket?
Anyone got 145 bucks burning a hole in their pocket? That’s what it would take to convert a direct drive Ingentis to Syncromesh based on using 8 pulleys and 5m of cable. This is one of the down-sides of the Ultimaker mechanics - it’s very pulley intensive.
-
—
—
Not really and Ingentis, but... Jan Derksen's (jand) CoreXY printing away
Not really and Ingentis, but…
-
—
—
Went on a little shopping spree yesterday
Went on a little shopping spree yesterday. Can you guess what I went with for hot ends by the Azteeg X3 Pro I ordered. Probably going to go ahead and get Simplify3d also.
-
—
—
90% done modeling the Eustatios in Solidworks (making slight changes as I go)
-
—
—
As I was cruising ebay I found this And looking at the design I thought "Why cant we make an active filament measuring device similarly?"
As I was cruising ebay I found this http://www.ebay.com/itm/Wire-Measuring-Machine-/331157067818?pt=LH_DefaultDomain_0&hash=item4d1a7fd82a And looking at the design I thought “Why cant we make an active filament measuring device similarly?”. This design would use a spring, 2 x 623vv bearings, a sliding pot, 3 x m3 screws, 1 x m2 screw, and the rest printed. Alternately a second axis, turned 90 degrees, could be added. Calibrate distance from the filament to the nozzle and away we go. My issue is this: my Arduino skills are non-existent. That and lack of firmware support which falls back on my issue again. I made this in all one part with enough space .1mm for each item to be separate. I exported to .stl and cura separated most of it except the top bearing. Any thoughts, ideas, help?
-
—
—
Is it true that adding gears to x/y axis we get backlash, reducing the precision of the machine
Is it true that adding gears to x/y axis we get backlash, reducing the precision of the machine. Anyone has a machine that has it? What would be the best gear reduction and model.
-
—
—
Just got notice that my massdrop steppers are stateside and being shipped to me
Just got notice that my massdrop steppers are stateside and being shipped to me. so got to print my belt conponents (eustathios design) to replace my current spectra design.
-
—
—
I'm thinking sorta seriously about adapting this for the Z axis
I’m thinking sorta seriously about adapting this for the Z axis. It’s probably cheaper than the Ø10mm bearing rods, and maybe easier to deal with (aluminum can be cut to length much more easily). With custom long carriages, it might even be more rigid.
-
—
—
Eric Lien was correct. I had to fix my belt system from the cross over to one on top and one on bottom
+Eric Lien was correct. I had to fix my belt system from the cross over to one on top and one on bottom. Made these little height extenders for the carriage. The motors should moved out about 6mm or so but that would require a new top piece. I will try her again and see how she goes.
-
—
—
I would like to know about the precision of Ingentis
I would like to know about the precision of Ingentis. Is direct drive more precise than Bowden? Is bushings better than linear bearings. If so where can I find those bushings. I really intent to build my 3d printer.
-
—
—
Originally shared by Mike Miller Ingentis/Quardap hybrid
Originally shared by Mike Miller
-
—
—
Old Build Plate....New Build Plate
Old Build Plate….New Build Plate
-
—
—
When building the structure I noticed that most you don't use brackets for the 90deg corners
When building the structure I noticed that most you don’t use brackets for the 90deg corners. Is that because the method you use to hold it together is strong enough and the brackets are to expensive
-
—
—
Using Simplify3D iam able to design parts in a way I just would not have before
Using Simplify3D iam able to design parts in a way I just would not have before. The supports just work, impressive!
-
—
—
D Rob As you asked i have attached photos of my printer
+D Rob As you asked i have attached photos of my printer. I am haveing extruder problems extrusion stops after 10-15mins of extrusions
-
—
—
Just a little pic to show where my printer is at
Just a little pic to show where my printer is at. Added space at the bottom for electronics and Z axis drive. I am liking the belt drive a lot better than the Spectra drive. Still trying to decide on hotends. May wait on the V6 E3D hotends.
-
—
—
One thing i have found is working with this Extrusion is a pain in the tail pipe
One thing i have found is working with this Extrusion is a pain in the tail pipe.
-
—
—
Shared on April 21, 2014 01:57...
Dale Dunn
-
—
—
hello guys, thanks for accepting me. I am new to this community
hello guys,
-
—
—
Mock up of how I think the kraken could be mounted
Mock up of how I think the kraken could be mounted. It would involve drilling and tapping 1 side and adding 90 degree thread/barbs. I’m putting this here to see what smarter people than me might think.. Would it be worth the hassle?
-
—
—
Got a package, Brian Bland ...I dunno what USPS ship method you used, but they mailed me every time the package moved 12 feet!
Got a package, +Brian Bland …I dunno what USPS ship method you used, but they mailed me every time the package moved 12 feet! The parts look GORGEOUS. A helluva lot better than the 3DR parts I paid a guy off ebay for!
-
—
—
Look what was in my mail box
Look what was in my mail box. Now I need to order more and belts. Mass drop motors haven’t shipped yet so I have plenty of wait time.
-
—
—
Shared on April 15, 2014 15:02...
D Rob
-
—
—
The Sinclair ZX10 of the printing age?
The Sinclair ZX10 of the printing age?
-
—
—
What have we here? Guys I'll package everything this weekend and try to so them Monday
What have we here? Guys I’ll package everything this weekend and try to so them Monday.
-
—
—
I have open ended GT2 belt now if anybody needs it
I have open ended GT2 belt now if anybody needs it. $1usd/ft shipped in the US.
-
—
—
Why would a PID auto tune fail, error says failed cuz temp is to high
Why would a PID auto tune fail, error says failed cuz temp is to high. When i turn the hotend on it will regulate the desire temp:ie 200c. Its just the AUTO tune that fails. I raised the #define PID_FUNCTIONAL_RANGE from 10 to 25 but didn’t change anything.
-
—
—
I've purchased the RUMBA board that's in the BOM for the ingentis...
I’ve purchased the RUMBA board that’s in the BOM for the ingentis… It says it is “universal voltage” and can take 12-35V input which is regulated to 12V for the fan / lights etc and 5v for the processor etc.
-
—
—
My revised electronics cabinet. The ribbon cable is the wiring for my RGB led strips
My revised electronics cabinet. The ribbon cable is the wiring for my RGB led strips
-
—
—
COREXY moving in all directions. End stops not mounted just plunged into the RAMPS with pig tales
COREXY moving in all directions. End stops not mounted just plunged into the RAMPS with pig tales.
-
—
—
Added to YouMagine! Add, delete, modify, clone away!
Added #Eustathios to YouMagine! Add, delete, modify, clone away!
-
—
—
Prusa i2 with prusa v1 nozzle printed most of the plastics for my new printer
Prusa i2 with prusa v1 nozzle printed most of the plastics for my new printer
-
—
—
Well guys, I've sent another e-mail requesting an eta on these bad boys
http://www.robotdigg.com/product/149/10mm-bore-32-teeth-gt2-pulley
-
—
—
Very first print! Originally shared by Jason Smith (Birds Of Paradise FPV)
Very first #Eustathios print!
-
—
—
Does anyone have a file for a printable tool to help me when I align the rods and tighten the spectra
Does anyone have a file for a printable tool to help me when I align the rods and tighten the spectra. I am sure I remember reading about it but cant find it anywhere now I am looking for it.
-
—
—
Here's my idea for a Z axis drive for an Ingentis or derivative
Here’s my idea for a Z axis drive for an Ingentis or derivative. Again, all three axes are shortened by 200 mm to keep everything in view.
-
—
—
Did people who got their extrusion off Misumi order 8x 1 meter lengths of the 20x20mm?
Did people who got their extrusion off Misumi order 8x 1 meter lengths of the 20x20mm? Or 2x 4m lengths?
-
—
—
Are there any endstops in the Ingentis design?
Are there any endstops in the Ingentis design? I’m sure not seeing any in the videos people have posted…
-
—
—
Some mediocre quality video while milling parts
Some mediocre quality video while milling #Eustathios parts.
-
—
—
Some pics of the plexiglass parts
Some pics of the #Eustathios plexiglass parts.
-
—
—
Thinking of playing with something like this: for the Z carriage
Thinking of playing with something like this: http://www.thingiverse.com/thing:126537 for the Z carriage. Has anyone played with this before? Worth looking at maybe? Benefits are very little friction, still holds its place on poweroff, and given enough force, the bearings will actually slide on the rod…
-
—
—
What size linear rods are people using for Ingentis?
What size linear rods are people using for Ingentis? The BOM shows a combination of 10mm and 8mm. Is that still the suggested types?
-
—
—
ABS or PLA? This is the printer that matters
ABS or PLA?
-
—
—
Ingentis Parts printing. Borrowed Prusa I2 with Prusa Nozzle V.1 tuned fairly well
Ingentis Parts printing. Borrowed Prusa I2 with Prusa Nozzle V.1 tuned fairly well.
-
—
—
It's pretty safe to assume nobody's printing ingentis parts for others yet, right?
It’s pretty safe to assume nobody’s printing ingentis parts for others yet, right?
-
—
—
Heating pads came in yesturday. 12" x 12". 5 total
Heating pads came in yesturday. 12” x 12”. 5 total.
-
—
—
Where should I post modified Ingentis parts?
Where should I post modified Ingentis parts? Should I post on Youmagine as a deviation of the Ingentis? I modified the Z axis parts for 12mm shafts and LMU12 linear bearings.
-
—
—
Received some of the parts. I have everything ordered but electronics, hot end, and motors .
Received some of the parts. I have everything ordered but electronics, hot end, and motors .
-
—
—
I noticed the z-axis is driven through gear with a single motor
I noticed the z-axis is driven through gear with a single motor. Can the design driven via 2 motors with threaded rod attached via coupler, like most reprap printers?
-
—
—
Can someone please help me convert a pdf of the ultimaker electronics 2.1.1 into a gerber compatible format?
Can someone please help me convert a pdf of the ultimaker electronics 2.1.1 into a gerber compatible format? I cant use pdf 2 gerb as it doesnt support 4 layer pcb. I want to maybe get a crowd fund going and get some pcbs. I’m really keen on building my first pcb from scratch and I’love this to be the board. If you cant help but know someone who can pass this along. I found a service for this type of thing but they want over 1000usd for the gerbers
-
—
—
In setting up a dual hotend, how do you account for the nozzle distance from each other
In setting up a dual hotend, how do you account for the nozzle distance from each other. I could make them 50mm apart or 55mm. How do you set that up.
-
—
—
OK, here's the idea I got based on the work Shauki Bagdadi has been doing on his Quadrap
OK, here’s the idea I got based on the work +Shauki Bagdadi has been doing on his Quadrap. There’s still a ton of work to be done here, but I’ve at least worked out that it all fits together without interference. Clearance is a little tight. There’s 2 mm between the beams and 0.5 mm between the Ø5 mm shafts.
-
—
—
Shared on March 16, 2014 07:10...
-
—
—
Here's a printed version of the spectra model xy end
Here’s a printed version of the spectra model xy end. And some renders of the belt version.
-
—
—
Tim Rastall This is what I was talking about having the ability to tension the belt in the slide itself.That block is free floating that gets pulled together with the 2 screw holes
+Tim Rastall This is what I was talking about having the ability to tension the belt in the slide itself.That block is free floating that gets pulled together with the 2 screw holes. BTW this is my little printer I have been playing with.
-
—
—
MISUMI USA are you able to tell me why you can't ship to Australia?
+MISUMI USA are you able to tell me why you can’t ship to Australia? :(
-
—
—
Here's my take on that xy end conversation
Here’s my take on that xy end conversation. Started from scratch with due consideration of the things we discussed.
-
—
—
I am sourcing to build a Ingentis, can I use a RAMPS 1.4 board?
I am sourcing to build a Ingentis, can I use a RAMPS 1.4 board? What is the recommended board?
-
—
—
Anyone taking an Ingentis or related printer to MRRF this weekend in Goshen, Indiana?
Anyone taking an Ingentis or related printer to MRRF this weekend in Goshen, Indiana? I’m contemplating building a new printer and would love to see one in person.
-
—
—
Yay! Misumi 150 came in build 2 in t minus...
Yay! Misumi 150 came in build 2 in t minus…
-
—
—
Just found this..
Just found this..
-
—
—
I keep seeing that people are using Spectra Line, but what I want to know is what size line?
I keep seeing that people are using Spectra Line, but what I want to know is what size line? 100LB? 5LB? What is the right balance of strength and flexibility?
-
—
—
So a ingentis is designed to only work with the bowden design right
So a ingentis is designed to only work with the bowden design right. Have you guys had any troubles with using the bowden design hotends if so what
-
—
—
Big fan of "the ideal" and "getting as close to perfection as possible: I have a question which I think we could ALL benefit from knowing the answer to: The Ingentis ( / UI-T-Slot / Eustathios ) is worlds ahead of my current
Big fan of “the ideal” and “getting as close to perfection as possible: I have a question which I think we could ALL benefit from knowing the answer to:
-
—
—
I have been looking at getting open ended GT2 belt
I have been looking at getting open ended GT2 belt. I am considering buying a bulk order to get it cheaper. If there is enough interest here, I will order and offer it for sale. In the US it will probably be ~$1.00 a foot shipped.
-
—
—
More than you ever thought you would want to know about gt2:
More than you ever thought you would want to know about gt2:
-
—
—
Shared on March 12, 2014 03:46...
-
—
—
to all and sundry: here are the Ul-T-Slot stls and solid parts enjoy and share
https://drive.google.com/file/d/0B72pKH5qHTlCMlFRcThJYldMSWM/edit?usp=sharing
-
—
—
Anyone figured out what options at Misumi to pick for the extrusion to be drilled appropriately for Tim's method for frame assembly?
Anyone figured out what options at Misumi to pick for the extrusion to be drilled appropriately for Tim’s method for frame assembly?
-
—
—
Shared on March 11, 2014 04:56...
http://www.servocity.com/html/vertical_shaft_worm_drive_gear.html#.Ux6XE_ldWVE
-
—
—
This is my technique for the frame
This is my technique for the frame. I believe ,as most people do in what they do, that this could be a superior frame layout and the vid explains why
-
—
—
How about something like this for the z stage?
How about something like this for the z stage?
-
—
—
Well, what to say. WOW I guess
Well, what to say. WOW I guess. Looks like belts work then. Lead screw driven Z too.
-
—
—
Alright everyone has been asking about z solutions for the ingentis this was the solution I decided on several months ago
Alright everyone has been asking about z solutions for the ingentis this was the solution I decided on several months ago. I printed it on my then not very well calibrated Mendel big12. Also the STK was 2x to big when I dl’d it from thing diverse and saw wouldn’t recognize features. Do I made the hub and the holes 2x to big and in Cura printed ½ scale. I think Bette can be done and a reduction worm box someone posted is my next try enjoy
-
—
—
The outer rods of the x / y gantry, they aren't just for linear motion, they also spin in order to drive the gantry, don't they...
The outer rods of the x / y gantry, they aren’t just for linear motion, they also spin in order to drive the gantry, don’t they…
-
—
—
Printed a few more parts for the Ingentis tonight
Printed a few more parts for the Ingentis tonight. Z axis parts.
-
—
—
Roller Bridge Joint for QR B2 I am convinced again and again that sliding joints are evil and waste of power
Roller Bridge Joint for QR B2
-
—
—
Here's an idea for an alternate xy gantry
Here’s an idea for an alternate xy gantry. I do like the idea of rollers for super accurate positioning of the carriage.
-
—
—
What's your build dimensions and specs? I'm thinking I'll go 24v with this one, a 12x12 heated build plate (probably on a 13x13 or 13.5x13.5 platform and 18" Z...because that's what the Makerbot Z18 will do for $6k
What’s your build dimensions and specs?
-
—
—
How stable is the ingentis? Worth looking at beefing up any rods or 4 rods for z axis or would that be TOO overkill because its rock-solid already?
How stable is the ingentis? Worth looking at beefing up any rods or 4 rods for z axis or would that be TOO overkill because its rock-solid already?
-
—
—
Got the go ahead from senior management* to buy the parts for an Ingentis :-) !
Got the go ahead from senior management* to buy the parts for an Ingentis :-) #Stoked !
-
—
—
Shared on March 08, 2014 06:41...
-
—
—
Shared on March 08, 2014 06:40...
-
—
—
Shared on March 07, 2014 06:49...
D Rob
-
—
—
my Ul-T-Slot but I'm making some revisions
my Ul-T-Slot but I’m making some revisions. As I speak. The access plate is inconvenient. instead I will flip the board and install it upside down in place of the clear Plexiglas and have a panel on the bottom for adjustments a la Ultimaker. The risers for the electronics/ z cabinet were an afterthought and are being replaced along with the longer upright extrusions by 22”long extrusions from top square frame to bottom square frame, and 4 x 16” lengths will run between for the bottom of the build area/top of the electronics cabinet. The bottom will be sealed by a panel secured to the tslot by m4 and t nuts. the panel corner will be routed to fit conformed to the Goopyplastic foot corners
-
—
—
worm tightened xy ends
worm tightened xy ends
-
—
—
here is the Ul-T-Slot z. It's spectra driven at the current design
here is the Ul-T-Slot z. It’s spectra driven at the current design.
-
—
—
Shared on March 07, 2014 05:00...
-
—
—
Shared on March 07, 2014 04:56...
http://www.geek.com/news/this-39000-3d-printer-can-prototype-full-sized-furniture-1585262/
-
—
—
I am just sharing an idea I had for the bearings on the Ingentis as the press fit ones were quite expensive including postage from the US so I thought I would give this a try first
I am just sharing an idea I had for the bearings on the Ingentis as the press fit ones were quite expensive including postage from the US so I thought I would give this a try first. It is just a tapered sleeve to hold the bearing, allowing it to move just like the self aligning ones in the BOM.
-
—
—
for the ingentis bed crash problem. here we go, a simple crash protection
for the ingentis bed crash problem. here we go, a simple crash protection. makes active z leveling impossible as is but hey I’m working on a solution for this too. ;)
-
—
—
requests for an order of gt2 10mm bore pulleys end in 1 hour for this order
requests for an order of gt2 10mm bore pulleys end in 1 hour for this order. Next order will have to wait until we have a large enough order again
-
—
—
Lead time for shipping after I order is estimated at 20 days and then shipping to me then to you
Lead time for shipping after I order is estimated at 20 days and then shipping to me then to you.
-
—
—
The orders for tonight on 32tooth 2mm gt2 with the un-findable (nearly) 10mm bore pulleys ends at 10:00pm central standard time
The orders for tonight on 32tooth 2mm gt2 with the un-findable (nearly) 10mm bore pulleys ends at 10:00pm central standard time. The shipping domestically (USPS First Class) is handled as below. Cost for each is $2.30 us.
-
—
—
Here is the deal. I have enough for an order to be placed
Here is the deal. I have enough for an order to be placed. At 10:00pm central standard time I’m closing this order. If there is a need large enough to place another order I will do so. Anyone ordering needs to pm me the quantity, normal, use email, PayPal email, Address to ship to, and whether you want fed ex or usps envelope. I will send each person an email with shipping and parts cost. The total shipping from the shop will be divided evenly among us and added to your payment. I will Itemize this and total it. I will accept payments via paypal and once everyone has made payment for their order I will place the order. I will notify all of you when the package arrives and send it on within 1 business day. I want to place the order within 48 hrs of the 10:00pm closing so these guys don’t have to wait too long. So please make payments quickly after I send your total. Or you may fall to the after 10 list lol
-
—
—
One of the variables in the current design that needs work is the Z-axis...sure, it currently produces fine results, but a loss of power has a platform crash in the Z direction...which is sub-optimal
One of the variables in the current design that needs work is the Z-axis…sure, it currently produces fine results, but a loss of power has a platform crash in the Z direction…which is sub-optimal. Springs can limit the damage but that seems, generally, like something that can be improved upon. (a 2am power failure should not result in a heart attack)
-
—
—
Hey guys, I'm trying to get an order together
Hey guys, I’m trying to get an order together. 10mm bore 2mm pitch 6mm wide 32 tooth gt2 pulleys. We have found a custom pulley source and these are perfect for an ingentis belt conversion. Min order is 50 and we wanted to see who all wants some. If you are interested let me know. If you use 10mm rod for z axle 12 will make a full conversion. 10 if not. I’ll be handling the order. So if your interested pm me your address to figure out the shipping. Pulleys will cost 2.30 ea plus post. Just send me your quantity address and you can send me what your total is via pay pay once all orders are placed I’ll order and send everyone their pulleys. If you have a preferred shipping method let me know. I’m getting 12 +Anthony Morris 10 +Tim Rastall 10 +Jim Squirrel 4 so we are up to 36 72% of the min.
-
—
—
So, I've set anyone who's name I recognise to moderator, please add categories as you see fit but don't go crazy(I reserve the right to delete them if they displease me, mwahhahhaha) .
So, I’ve set anyone who’s name I recognise to moderator, please add categories as you see fit but don’t go crazy(I reserve the right to delete them if they displease me, mwahhahhaha) . I’ve promoted +D Rob to owner as his Ultislot machine is more of a close cousin of Ingentis and he’s implemented a number of improvements worth considering.
February 2019
January 2019
December 2018
November 2018
October 2018
September 2018
August 2018
July 2018
June 2018
May 2018
April 2018
March 2018
February 2018
January 2018
December 2017
November 2017
October 2017
September 2017
August 2017
July 2017
June 2017
May 2017
April 2017
March 2017
February 2017
January 2017
December 2016
November 2016
October 2016
September 2016
August 2016
July 2016
June 2016
May 2016
April 2016
March 2016
February 2016
January 2016
December 2015
November 2015
October 2015
September 2015
August 2015
July 2015
June 2015
May 2015
April 2015
March 2015
February 2015
January 2015
December 2014
November 2014
October 2014
September 2014
August 2014
July 2014
June 2014
May 2014
April 2014
March 2014
subscribe via RSS